kernel/linux.git/drivers/input/touchscreen, branch v6.6.132

Input: ti_am335x_tsc - fix off-by-one error in wire_order validation

2026-01-11T14:21:49+00:00

commit 248d3a73a0167dce15ba100477c3e778c4787178 upstream. The current validation 'wire_order[i] > ARRAY_SIZE(config_pins)' allows wire_order[i] to equal ARRAY_SIZE(config_pins), which causes out-of-bounds access when used as index in 'config_pins[wire_order[i]]'. Since config_pins has 4 elements (indices 0-3), the valid range for wire_order should be 0-3. Fix the off-by-one error by using >= instead of > in the validation check. Signed-off-by: Junjie Cao Link: https://patch.msgid.link/20251114062817.852698-1-junjie.cao@intel.com Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable") Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: goodix - add support for ACPI ID GDIX1003

2025-12-01T10:41:41+00:00

commit c6d99e488117201c63efd747ce17b80687c3f5a9 upstream. Some newer devices use an ACPI hardware ID of GDIX1003 for their Goodix touchscreen controller, instead of GDIX1001 / GDIX1002. Add GDIX1003 to the goodix_acpi_match[] table. Reported-by: Weikang Guo Closes: https://lore.kernel.org/linux-input/20250225024409.1467040-1-guoweikang.kernel@gmail.com/ Tested-by: Weikang Guo Signed-off-by: Hans de Goede Link: https://lore.kernel.org/r/20251013121022.44333-1-hansg@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: atmel_mxt_ts - allow reset GPIO to sleep

2025-10-15T09:58:09+00:00

commit c7866ee0a9ddd9789faadf58cdac6abd7aabf045 upstream. The reset GPIO is not toggled in any critical section where it couldn't sleep, allow the reset GPIO to sleep. This allows the driver to operate reset GPIOs connected to I2C GPIO expanders. Signed-off-by: Marek Vasut Link: https://lore.kernel.org/r/20251005023335.166483-1-marek.vasut@mailbox.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

minmax: don't use max() in situations that want a C constant expression

2025-10-02T11:42:55+00:00

[ Upstream commit cb04e8b1d2f24c4c2c92f7b7529031fc35a16fed ] We only had a couple of array[] declarations, and changing them to just use 'MAX()' instead of 'max()' fixes the issue. This will allow us to simplify our min/max macros enormously, since they can now unconditionally use temporary variables to avoid using the argument values multiple times. Cc: David Laight Cc: Lorenzo Stoakes Signed-off-by: Linus Torvalds Signed-off-by: Eliav Farber Signed-off-by: Greg Kroah-Hartman

Input: cyttsp5 - fix power control issue on wakeup

2025-05-18T06:24:06+00:00

commit 7675b5efd81fe6d524e29d5a541f43201e98afa8 upstream. The power control function ignores the "on" argument when setting the report ID, and thus is always sending HID_POWER_SLEEP. This causes a problem when trying to wakeup. Fix by sending the state variable, which contains the proper HID_POWER_ON or HID_POWER_SLEEP based on the "on" argument. Fixes: 3c98b8dbdced ("Input: cyttsp5 - implement proper sleep and wakeup procedures") Cc: stable@vger.kernel.org Signed-off-by: Mikael Gonella-Bolduc Signed-off-by: Hugo Villeneuve Reviewed-by: Alistair Francis Link: https://lore.kernel.org/r/20250423135243.1261460-1-hugo@hugovil.com Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: cyttsp5 - ensure minimum reset pulse width

2025-05-18T06:24:05+00:00

commit c6cb8bf79466ae66bd0d07338c7c505ce758e9d7 upstream. The current reset pulse width is measured to be 5us on a Renesas RZ/G2L SOM. The manufacturer's minimum reset pulse width is specified as 10us. Extend reset pulse width to make sure it is long enough on all platforms. Also reword confusing comments about reset pin assertion. Fixes: 5b0c03e24a06 ("Input: Add driver for Cypress Generation 5 touchscreen") Cc: stable@vger.kernel.org Acked-by: Alistair Francis Signed-off-by: Hugo Villeneuve Link: https://lore.kernel.org/r/20250410184633.1164837-1-hugo@hugovil.com Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: ads7846 - fix gpiod allocation

2025-03-22T19:50:45+00:00

commit c9ccb88f534ca760d06590b67571c353a2f0cbcd upstream. commit 767d83361aaa ("Input: ads7846 - Convert to use software nodes") has simplified the code but accidentially converted a devm_gpiod_get() to gpiod_get(). This leaves the gpio reserved on module remove and the driver can no longer be loaded again. Fixes: 767d83361aaa ("Input: ads7846 - Convert to use software nodes") Cc: stable@vger.kernel.org Signed-off-by: H. Nikolaus Schaller Link: https://lore.kernel.org/r/6e9b143f19cdfda835711a8a7a3966e5a2494cff.1738410204.git.hns@goldelico.com Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: edt-ft5x06 - fix regmap leak when probe fails

2024-11-08T15:28:25+00:00

[ Upstream commit bffdf9d7e51a7be8eeaac2ccf9e54a5fde01ff65 ] The driver neglects to free the instance of I2C regmap constructed at the beginning of the edt_ft5x06_ts_probe() method when probe fails. Additionally edt_ft5x06_ts_remove() is freeing the regmap too early, before the rest of the device resources that are managed by devm are released. Fix this by installing a custom devm action that will ensure that the regmap is released at the right time during normal teardown as well as in case of probe failure. Note that devm_regmap_init_i2c() could not be used because the driver may replace the original regmap with a regmap specific for M06 devices in the middle of the probe, and using devm_regmap_init_i2c() would result in releasing the M06 regmap too early. Reported-by: Li Zetao Fixes: 9dfd9708ffba ("Input: edt-ft5x06 - convert to use regmap API") Cc: stable@vger.kernel.org Reviewed-by: Oliver Graute Link: https://lore.kernel.org/r/ZxL6rIlVlgsAu-Jv@google.com Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin

Input: ilitek_ts_i2c - add report id message validation

2024-10-04T14:29:28+00:00

[ Upstream commit 208989744a6f01bed86968473312d4e650e600b3 ] Ensure that the touchscreen response has correct "report id" byte before processing the touch data and discard other messages. Fixes: 42370681bd46 ("Input: Add support for ILITEK Lego Series") Signed-off-by: Emanuele Ghidoli Signed-off-by: Francesco Dolcini Link: https://lore.kernel.org/r/20240805085511.43955-3-francesco@dolcini.it Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin

Input: ilitek_ts_i2c - avoid wrong input subsystem sync

2024-10-04T14:29:28+00:00

[ Upstream commit 7d0b18cd5dc7429917812963611d961fd93cb44d ] For different reasons i2c transaction may fail or report id in the message may be wrong. Avoid closing the frame in this case as it will result in all contacts being dropped, indicating that nothing is touching the screen anymore, while usually it is not the case. Fixes: 42370681bd46 ("Input: Add support for ILITEK Lego Series") Signed-off-by: Emanuele Ghidoli Signed-off-by: Francesco Dolcini Link: https://lore.kernel.org/r/20240805085511.43955-2-francesco@dolcini.it Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin