kernel/linux.git/drivers/input/touchscreen/goodix.c, branch v6.1.168

Input: goodix - accept ACPI resources with gpio_count == 3 && gpio_int_idx == 0

2024-03-01T12:26:26+00:00

[ Upstream commit 180a8f12c21f41740fee09ca7f7aa98ff5bb99f8 ] Some devices list 3 Gpio resources in the ACPI resource list for the touchscreen: 1. GpioInt resource pointing to the GPIO used for the interrupt 2. GpioIo resource pointing to the reset GPIO 3. GpioIo resource pointing to the GPIO used for the interrupt Note how the third extra GpioIo resource really is a duplicate of the GpioInt provided info. Ignore this extra GPIO, treating this setup the same as gpio_count == 2 && gpio_int_idx == 0 fixes the touchscreen not working on the Thunderbook Colossus W803 rugged tablet and likely also on the CyberBook_T116K. Reported-by: Maarten van der Schrieck Closes: https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/-/issues/22 Suggested-by: Maarten van der Schrieck Tested-by: Maarten van der Schrieck Signed-off-by: Hans de Goede Link: https://lore.kernel.org/r/20231223141650.10679-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov Signed-off-by: Sasha Levin

Input: goodix - ensure int GPIO is in input for gpio_count == 1 && gpio_int_idx == 0 case

2023-10-19T21:08:57+00:00

commit 423622a90abb243944d1517b9f57db53729e45c4 upstream. Add a special case for gpio_count == 1 && gpio_int_idx == 0 to goodix_add_acpi_gpio_mappings(). It seems that on newer x86/ACPI devices the reset and irq GPIOs are no longer listed as GPIO resources instead there is only 1 GpioInt resource and _PS0 does the whole reset sequence for us. This means that we must call acpi_device_fix_up_power() on these devices to ensure that the chip is reset before we try to use it. This part was already fixed in commit 3de93e6ed2df ("Input: goodix - call acpi_device_fix_up_power() in some cases") by adding a call to acpi_device_fix_up_power() to the generic "Unexpected ACPI resources" catch all. But it turns out that this case on some hw needs some more special handling. Specifically the firmware may bootup with the IRQ pin in output mode. The reset sequence from ACPI _PS0 (executed by acpi_device_fix_up_power()) should put the pin in input mode, but the GPIO subsystem has cached the direction at bootup, causing request_irq() to fail due to gpiochip_lock_as_irq() failure: [ 9.119864] Goodix-TS i2c-GDIX1002:00: Unexpected ACPI resources: gpio_count 1, gpio_int_idx 0 [ 9.317443] Goodix-TS i2c-GDIX1002:00: ID 911, version: 1060 [ 9.321902] input: Goodix Capacitive TouchScreen as /devices/pci0000:00/0000:00:17.0/i2c_designware.4/i2c-5/i2c-GDIX1002:00/input/input8 [ 9.327840] gpio gpiochip0: (INT3453:00): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ [ 9.327856] gpio gpiochip0: (INT3453:00): unable to lock HW IRQ 26 for IRQ [ 9.327861] genirq: Failed to request resources for GDIX1002:00 (irq 131) on irqchip intel-gpio [ 9.327912] Goodix-TS i2c-GDIX1002:00: request IRQ failed: -5 Fix this by adding a special case for gpio_count == 1 && gpio_int_idx == 0 which adds an ACPI GPIO lookup table for the int GPIO even though we cannot use it for reset purposes (as there is no reset GPIO). Adding the lookup will make the gpiod_int = gpiod_get(..., GPIOD_IN) call succeed, which will explicitly set the direction to input fixing the issue. Note this re-uses the acpi_goodix_int_first_gpios[] lookup table, since there is only 1 GPIO in the ACPI resources the reset entry in that lookup table will amount to a no-op. Reported-and-tested-by: Michael Smith <1973.mjsmith@gmail.com> Signed-off-by: Hans de Goede Link: https://lore.kernel.org/r/20231003215144.69527-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: goodix - add Lenovo Yoga Book X90F to nine_bytes_report DMI table

2023-04-06T10:10:50+00:00

commit 8a0432bab6ea3203d220785da7ab3c7677f70ecb upstream. The Android Lenovo Yoga Book X90F / X90L uses the same goodix touchscreen with 9 bytes touch reports for its touch keyboard as the already supported Windows Lenovo Yoga Book X91F/L, add a DMI match for this to the nine_bytes_report DMI table. When the quirk for the X91F/L was initially added it was written to also apply to the X90F/L but this does not work because the Android version of the Yoga Book uses completely different DMI strings. Also adjust the X91F/L quirk to reflect that it only applies to the X91F/L models. Signed-off-by: Hans de Goede Reviewed-by: Bastien Nocera Link: https://lore.kernel.org/r/20230315134442.71787-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov Signed-off-by: Greg Kroah-Hartman

Input: goodix - try resetting the controller when no config is set

2022-11-03T19:49:35+00:00

On ACPI systems (irq_pin_access_method == IRQ_PIN_ACCESS_ACPI_*) the driver does not reset the controller at probe time, because sometimes the system firmware loads a config and resetting might loose this config. On the Nanote UMPC-01 device OTOH the config is in flash of the controller, the controller needs a reset to load this; and the system firmware does not reset the controller on a cold boot. To fix the Nanote UMPC-01 touchscreen not working on a cold boot, try resetting the controller and then re-reading the config when encountering a config with 0 width/height/max_touch_num value and the controller has not already been reset by goodix_ts_probe(). This should be safe to do in general because normally we should never encounter a config with 0 width/height/max_touch_num. Doing this in general not only avoids the need for a DMI quirk, but also might help other systems. Signed-off-by: Hans de Goede Reviewed-by: Bastien Nocera Link: https://lore.kernel.org/r/20221025122930.421377-2-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2022-10-10T05:30:23+00:00

Prepare input updates for 6.1 merge window.

Input: goodix - add compatible string for GT1158

2022-08-23T17:23:37+00:00

Add compatible string for GT1158 missing from the previous patch. Fixes: 425fe4709c76 ("Input: goodix - add support for GT1158") Signed-off-by: Jarrah Gosbell Link: https://lore.kernel.org/r/20220813043821.9981-1-kernel@undef.tools Signed-off-by: Dmitry Torokhov

i2c: Make remove callback return void

2022-08-16T10:46:26+00:00

The value returned by an i2c driver's remove function is mostly ignored. (Only an error message is printed if the value is non-zero that the error is ignored.) So change the prototype of the remove function to return no value. This way driver authors are not tempted to assume that passing an error to the upper layer is a good idea. All drivers are adapted accordingly. There is no intended change of behaviour, all callbacks were prepared to return 0 before. Reviewed-by: Peter Senna Tschudin Reviewed-by: Jeremy Kerr Reviewed-by: Benjamin Mugnier Reviewed-by: Javier Martinez Canillas Reviewed-by: Crt Mori Reviewed-by: Heikki Krogerus Acked-by: Greg Kroah-Hartman Acked-by: Marek Behún # for leds-turris-omnia Acked-by: Andy Shevchenko Reviewed-by: Petr Machata # for mlxsw Reviewed-by: Maximilian Luz # for surface3_power Acked-by: Srinivas Pandruvada # for bmc150-accel-i2c + kxcjk-1013 Reviewed-by: Hans Verkuil # for media/* + staging/media/* Acked-by: Miguel Ojeda # for auxdisplay/ht16k33 + auxdisplay/lcd2s Reviewed-by: Luca Ceresoli # for versaclock5 Reviewed-by: Ajay Gupta # for ucsi_ccg Acked-by: Jonathan Cameron # for iio Acked-by: Peter Rosin # for i2c-mux-*, max9860 Acked-by: Adrien Grassein # for lontium-lt8912b Reviewed-by: Jean Delvare # for hwmon, i2c-core and i2c/muxes Acked-by: Corey Minyard # for IPMI Reviewed-by: Vladimir Oltean Acked-by: Dmitry Torokhov Acked-by: Sebastian Reichel # for drivers/power Acked-by: Krzysztof Hałasa Signed-off-by: Uwe Kleine-König Signed-off-by: Wolfram Sang

Input: goodix - add support for GT1158

2022-08-11T23:18:20+00:00

This controller is used by PinePhone and PinePhone Pro. Support for the PinePhone Pro will be added in a later patch set. Signed-off-by: Ondrej Jirman Signed-off-by: Jarrah Gosbell Reviewed-by: Hans de Goede Link: https://lore.kernel.org/r/20220809091200.290492-1-kernel@undef.tools Signed-off-by: Dmitry Torokhov

Merge branch 'next' into for-linus

2022-08-02T17:06:12+00:00

Prepare input updates for 5.20 (or 6.0) merge window.

Input: goodix - call acpi_device_fix_up_power() in some cases

2022-07-09T04:54:17+00:00

On ACPI boards, when we cannot get the GPIOs to do a reset ourselves if necessary, call acpi_device_fix_up_power() to force the ACPI _PS0 method to run. On some devices without proper GPIO descriptions this will reset the touchscreen for us and this may be necessary for us to be able to communicate to the touchscreen at all. Specifically on an Aya Neo Next this change will cause the _PS0() ACPI function to call INIT() which does: Method (INIT, 0, Serialized) { TP_I = 0x00A50000 TP_R = 0x00A50000 Sleep (0x0A) TP_I = 0x00E50000 Sleep (One) TP_R = 0x00E50000 Sleep (0x06) TP_I = 0x00A50000 Sleep (0x3C) TP_I = 0x00041800 } On older kernels the ACPI core assumed a power-on was necessary by itself and would run _PS0 before our probe function runs, which can be seen from the GPIO pin ctrl registers in /sys/kernel/debug/gpio which match the above hex values with older kernels. With newer kernels before this change the GPIO pin ctrl registers do not match, indicating INIT() has not run and probing the touchscreen fails. This change makes Linux run _PS0() again fixing the touchscreen not working on the Aya Neo Next. Reported-and-tested-by: Maya Matuszczyk Signed-off-by: Hans de Goede Link: https://lore.kernel.org/r/20220618210233.208027-1-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov