kernel/linux.git/drivers/iio, branch v4.14.85

iio: adc: at91: fix wrong channel number in triggered buffer mode

2018-11-13T19:15:09+00:00

commit aea835f2dc8a682942b859179c49ad1841a6c8b9 upstream. When channels are registered, the hardware channel number is not the actual iio channel number. This is because the driver is probed with a certain number of accessible channels. Some pins are routed and some not, depending on the description of the board in the DT. Because of that, channels 0,1,2,3 can correspond to hardware channels 2,3,4,5 for example. In the buffered triggered case, we need to do the translation accordingly. Fixed the channel number to stop reading the wrong channel. Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.") Cc: Maxime Ripard Signed-off-by: Eugen Hristev Acked-by: Ludovic Desroches Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: adc: at91: fix acking DRDY irq on simple conversions

2018-11-13T19:15:08+00:00

commit bc1b45326223e7e890053cf6266357adfa61942d upstream. When doing simple conversions, the driver did not acknowledge the DRDY irq. If this irq status is not acked, it will be left pending, and as soon as a trigger is enabled, the irq handler will be called, it doesn't know why this status has occurred because no channel is pending, and then it will go int a irq loop and board will hang. To avoid this situation, read the LCDR after a raw conversion is done. Fixes: 0e589d5fb ("ARM: AT91: IIO: Add AT91 ADC driver.") Cc: Maxime Ripard Signed-off-by: Eugen Hristev Acked-by: Ludovic Desroches Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: adc: imx25-gcq: Fix leak of device_node in mx25_gcq_setup_cfgs()

2018-11-13T19:15:08+00:00

commit d3fa21c73c391975488818b085b894c2980ea052 upstream. Leaving for_each_child_of_node loop we should release child device node, if it is not stored for future use. Found by Linux Driver Verification project (linuxtesting.org). JC: I'm not sending this as a quick fix as it's been wrong for years, but good to pick up for stable after the merge window. Signed-off-by: Alexey Khoroshilov Fixes: 6df2e98c3ea56 ("iio: adc: Add imx25-gcq ADC driver") Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: ad5064: Fix regulator handling

2018-11-13T19:15:08+00:00

commit 8911a43bc198877fad9f4b0246a866b26bb547ab upstream. The correct way to handle errors returned by regualtor_get() and friends is to propagate the error since that means that an regulator was specified, but something went wrong when requesting it. For handling optional regulators, e.g. when the device has an internal vref, regulator_get_optional() should be used to avoid getting the dummy regulator that the regulator core otherwise provides. Signed-off-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

Revert "iio: temperature: maxim_thermocouple: add MAX31856 part"

2018-10-10T06:54:24+00:00

[ Upstream commit 65099ea85e885c3ea1272eca8774b771419d8ce8 ] This reverts commit 535fba29b3e1afef4ba201b3c69a6992583ec0bd. Seems the submitter (er me, hang head in shame) didn't look at the datasheet enough to see that the registers are quite different. This needs to be reverted because a) would never work b) to open it be added to a Maxim RTDs (Resistance Temperature Detectors) under development by author Signed-off-by: Matt Ranostay Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

iio: 104-quad-8: Fix off-by-one error in register selection

2018-10-04T00:00:53+00:00

[ Upstream commit 2873c3f0e2bd12a7612e905c920c058855f4072a ] The reset flags operation is selected by bit 2 in the "Reset and Load Signals Decoders" register, not bit 1. Fixes: 28e5d3bb0325 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8") Signed-off-by: William Breathitt Gray Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

iio: accel: adxl345: convert address field usage in iio_chan_spec

2018-10-04T00:00:50+00:00

[ Upstream commit 9048f1f18a70a01eaa3c8e7166fdb2538929d780 ] Currently the address field in iio_chan_spec is filled with an accel data register address for the corresponding axis. In preparation for adding calibration offset support, this sets the address field to the index of accel data registers instead of the actual register address. This change makes it easier to access both accel registers and calibration offset registers with fewer lines of code as these are located in X-axis, Y-axis, Z-axis order. Cc: Eva Rachel Retuya Cc: Andy Shevchenko Cc: Jonathan Cameron Signed-off-by: Akinobu Mita Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

iio: adc: ina2xx: avoid kthread_stop() with stale task_struct

2018-10-04T00:00:45+00:00

[ Upstream commit 7d6cd21d82bacab2d1786fe5e989e4815b75d9a3 ] When the buffer is enabled for ina2xx driver, a dedicated kthread is invoked to capture mesurement data. When the buffer is disabled, the kthread is stopped. However if the kthread gets register access errors, it immediately exits and when the malfunctional buffer is disabled, the stale task_struct pointer is accessed as there is no kthread to be stopped. A similar issue in the usbip driver is prevented by kthread_get_run and kthread_stop_put helpers by increasing usage count of the task_struct. This change applies the same solution. Cc: Stefan Brüns Cc: Jonathan Cameron Signed-off-by: Akinobu Mita Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Signed-off-by: Jonathan Cameron Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

iio: ad9523: Fix return value for ad952x_store()

2018-09-09T17:55:56+00:00

commit 9a5094ca29ea9b1da301b31fd377c0c0c4c23034 upstream. A sysfs write callback function needs to either return the number of consumed characters or an error. The ad952x_store() function currently returns 0 if the input value was "0", this will signal that no characters have been consumed and the function will be called repeatedly in a loop indefinitely. Fix this by returning number of supplied characters to indicate that the whole input string has been consumed. Signed-off-by: Lars-Peter Clausen Signed-off-by: Alexandru Ardelean Fixes: cd1678f96329 ("iio: frequency: New driver for AD9523 SPI Low Jitter Clock Generator") Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman

iio: ad9523: Fix displayed phase

2018-09-09T17:55:56+00:00

commit 5a4e33c1c53ae7d4425f7d94e60e4458a37b349e upstream. Fix the displayed phase for the ad9523 driver. Currently the most significant decimal place is dropped and all other digits are shifted one to the left. This is due to a multiplication by 10, which is not necessary, so remove it. Signed-off-by: Lars-Peter Clausen Signed-off-by: Alexandru Ardelean Fixes: cd1678f9632 ("iio: frequency: New driver for AD9523 SPI Low Jitter Clock Generator") Cc: Signed-off-by: Jonathan Cameron Signed-off-by: Greg Kroah-Hartman