kernel/linux.git/drivers/gpu/host1x/hw, branch v5.17.9

gpu: host1x: Add initial runtime PM and OPP support

2021-12-16T13:07:07+00:00

Add runtime PM and OPP support to the Host1x driver. For the starter we will keep host1x always-on because dynamic power management require a major refactoring of the driver code since lot's of code paths are missing the RPM handling and we're going to remove some of these paths in the future. Reviewed-by: Ulf Hansson Tested-by: Peter Geis # Ouya T30 Tested-by: Paul Fertser # PAZ00 T20 Tested-by: Nicolas Chauvet # PAZ00 T20 and TK1 T124 Tested-by: Matt Merhar # Ouya T30 Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding

gpu: host1x: debug: Dump DMASTART and DMAEND register

2021-08-13T16:23:32+00:00

Show the values of the DMASTART and DMAEND registers when dumping status to help with failure analysis. Signed-off-by: Thierry Reding

gpu: host1x: debug: Dump only relevant parts of CDMA push buffer

2021-08-13T16:23:32+00:00

Dumping the full CDMA push buffer takes a long time and isn't very useful since most of the contents are not relevant. Instead only show the CDMA push buffer entries associated with current jobs. While at it, tweak the indentation a bit to make the output more readable. Signed-off-by: Thierry Reding

gpu: host1x: debug: Use dma_addr_t more consistently

2021-08-13T16:23:32+00:00

The host1x debug code uses a mix of phys_addr_t, dma_addr_t and u32 to represent addresses. However, these addresses are always DMA addresses so use the appropriate type. This fixes some issues with how these addresses are displayed, because they could be truncated in some cases and not show the full address. Signed-off-by: Thierry Reding

gpu: host1x: Add support for syncpoint waits in CDMA pushbuffer

2021-08-10T12:41:19+00:00

Add support for inserting syncpoint waits in the CDMA pushbuffer. These waits need to be done in HOST1X class, while gather submitted by the application execute in engine class. Support is added by converting the gather list of job into a command list that can include both gathers and waits. When the job is submitted, these commands are pushed as the appropriate opcodes on the CDMA pushbuffer. Also supported are waits relative to the start of the job, which are useful for jobs doing multiple things with an engine that doesn't natively support pipelining. While at it, use 32-bit waits on chips that support them. Signed-off-by: Mikko Perttunen Signed-off-by: Thierry Reding

gpu: host1x: Add no-recovery mode

2021-08-10T12:40:23+00:00

Add a new property for jobs to enable or disable recovery i.e. CPU increments of syncpoints to max value on job timeout. This allows for a more solid model for hanged jobs, where userspace doesn't need to guess if a syncpoint increment happened because the job completed, or because job timeout was triggered. On job timeout, we stop the channel, NOP all future jobs on the channel using the same syncpoint, mark the syncpoint as locked and resume the channel from the next job, if any. The future jobs are NOPed, since because we don't do the CPU increments, the value of the syncpoint is no longer synchronized, and any waiters would become confused if a future job incremented the syncpoint. The syncpoint is marked locked to ensure that any future jobs cannot increment the syncpoint either, until the application has recognized the situation and reallocated the syncpoint. Signed-off-by: Mikko Perttunen Signed-off-by: Thierry Reding

gpu: host1x: Fix Tegra194 syncpt interrupt threshold

2021-03-31T15:42:14+00:00

Syncpoint interrupts are not working as expected on Tegra194. The problem is that the syncpoint interrupt threshold being used is the global interrupt threshold and not the virtual interrupt threshold. Fix this by using the virtual interrupt threshold which aligns with downstream. Signed-off-by: Jon Hunter Signed-off-by: Mikko Perttunen Signed-off-by: Thierry Reding

gpu: host1x: Cleanup and refcounting for syncpoints

2021-03-31T15:42:13+00:00

Add reference counting for allocated syncpoints to allow keeping them allocated while jobs are referencing them. Additionally, clean up various places using syncpoint IDs to use host1x_syncpt pointers instead. Signed-off-by: Mikko Perttunen Signed-off-by: Thierry Reding

gpu: host1x: debug: Dump push buffer state

2020-07-17T14:06:14+00:00

When job hangs and there is a memory error pointing at channel's push buffer, it is very handy to know the push buffer's state. This patch makes the push buffer's state to be dumped into KMSG in addition to the job's gathers. Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 282

2019-06-05T15:36:37+00:00

Based on 1 normalized pattern(s): this software is licensed under the terms of the gnu general public license version 2 as published by the free software foundation and may be copied distributed and modified under those terms this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 285 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Alexios Zavras Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de Signed-off-by: Greg Kroah-Hartman