kernel/linux.git/drivers/gpu/drm/vc4, branch v6.1.22

drm/vc4: hdmi: Correct interlaced timings again

2023-03-10T08:33:11+00:00

[ Upstream commit 771d6539f27bd55f43d8a95d53a7eeaaffa2681c ] The back porch timings were correct, only the sync offset was wrong. Correct timing is now reported for 1080i and 576i, but the h offset is incorrect for 480i for non-obvious reasons. Fixes: fb10dc451c0f ("drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes") Signed-off-by: Dave Stevenson Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-14-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: hvs: Fix colour order for xRGB1555 on HVS5

2023-03-10T08:33:11+00:00

[ Upstream commit 902973dc1a049c0d7bf0c222b8f2b3876f01b4a2 ] Same as the xRGB8888 formats, HVS5 has managed to swap the colour channels for the xRGB1555 formats as well. Add the relevant config for pixel_order_hvs5. Fixes: c54619b0bfb3 ("drm/vc4: Add support for the BCM2711 HVS5") Signed-off-by: Dave Stevenson Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-6-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: hvs: Correct interrupt masking bit assignment for HVS5

2023-03-10T08:33:11+00:00

[ Upstream commit 87551ec650bb87d35f1b29bba6a2430896e08da0 ] HVS5 has moved the interrupt enable bits around within the DISPCTRL register, therefore the configuration has to be updated to account for this. Fixes: c54619b0bfb3 ("drm/vc4: Add support for the BCM2711 HVS5") Signed-off-by: Dave Stevenson Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-4-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: hvs: SCALER_DISPBKGND_AUTOHS is only valid on HVS4

2023-03-10T08:33:11+00:00

[ Upstream commit 982ee94486863a41c6af9f2ab3f6681f72bc5c48 ] The bit used for SCALER_DISPBKGND_AUTOHS in SCALER_DISPBKGNDX has been repurposed on HVS5 to configure whether a display can win back-to-back arbitration wins for the COB. This is not desirable, therefore only select this bit on HVS4, and explicitly clear it on HVS5. Fixes: c54619b0bfb3 ("drm/vc4: Add support for the BCM2711 HVS5") Signed-off-by: Dave Stevenson Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-3-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: hvs: Set AXI panic modes

2023-03-10T08:33:11+00:00

[ Upstream commit df993fced230daa8452892406f3180c93ebf7e7b ] The HVS can change AXI request mode based on how full the COB FIFOs are. Until now the vc4 driver has been relying on the firmware to have set these to sensible values. With HVS channel 2 now being used for live video, change the panic mode for all channels to be explicitly set by the driver, and the same for all channels. Fixes: c54619b0bfb3 ("drm/vc4: Add support for the BCM2711 HVS5") Signed-off-by: Dave Stevenson Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-2-1f8e0770798b@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: drop all currently held locks if deadlock happens

2023-03-10T08:33:10+00:00

[ Upstream commit 479d4f0be4237ba33bc9432787aeb62c90e30f95 ] If vc4_hdmi_reset_link() returns -EDEADLK, it means that a deadlock happened in the locking context. This situation should be addressed by dropping all currently held locks and block until the contended lock becomes available. Currently, vc4 is not dealing with the deadlock properly, producing the following output when PROVE_LOCKING is enabled: [ 825.612809] ------------[ cut here ]------------ [ 825.612852] WARNING: CPU: 1 PID: 116 at drivers/gpu/drm/drm_modeset_lock.c:276 drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.613458] Modules linked in: 8021q mrp garp stp llc raspberrypi_cpufreq brcmfmac brcmutil crct10dif_ce hci_uart cfg80211 btqca btbcm bluetooth vc4 raspberrypi_hwmon snd_soc_hdmi_codec cec clk_raspberrypi ecdh_generic drm_display_helper ecc rfkill drm_dma_helper drm_kms_helper pwm_bcm2835 bcm2835_thermal bcm2835_rng rng_core i2c_bcm2835 drm fuse ip_tables x_tables ipv6 [ 825.613735] CPU: 1 PID: 116 Comm: kworker/1:2 Tainted: G W 6.1.0-rc6-01399-g941aae326315 #3 [ 825.613759] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 825.613777] Workqueue: events output_poll_execute [drm_kms_helper] [ 825.614038] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 825.614063] pc : drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.614603] lr : drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.614829] sp : ffff800008313bf0 [ 825.614844] x29: ffff800008313bf0 x28: ffffcd7778b8b000 x27: 0000000000000000 [ 825.614883] x26: 0000000000000001 x25: 0000000000000001 x24: ffff677cc35c2758 [ 825.614920] x23: ffffcd7707d01430 x22: ffffcd7707c3edc7 x21: 0000000000000001 [ 825.614958] x20: 0000000000000000 x19: ffff800008313c10 x18: 000000000000b6d3 [ 825.614995] x17: ffffcd777835e214 x16: ffffcd7777cef870 x15: fffff81000000000 [ 825.615033] x14: 0000000000000000 x13: 0000000000000099 x12: 0000000000000002 [ 825.615070] x11: 72917988020af800 x10: 72917988020af800 x9 : 72917988020af800 [ 825.615108] x8 : ffff677cc665e0a8 x7 : d00a8c180000110c x6 : ffffcd77774c0054 [ 825.615145] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 825.615181] x2 : ffff677cc55e1880 x1 : ffffcd7777cef8ec x0 : ffff800008313c10 [ 825.615219] Call trace: [ 825.615232] drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.615773] drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.616003] output_poll_execute+0xe4/0x224 [drm_kms_helper] [ 825.616233] process_one_work+0x2b4/0x618 [ 825.616264] worker_thread+0x24c/0x464 [ 825.616288] kthread+0xec/0x110 [ 825.616310] ret_from_fork+0x10/0x20 [ 825.616335] irq event stamp: 7634 [ 825.616349] hardirqs last enabled at (7633): [] _raw_spin_unlock_irq+0x3c/0x78 [ 825.616384] hardirqs last disabled at (7634): [] __schedule+0x134/0x9f0 [ 825.616411] softirqs last enabled at (7630): [] local_bh_enable+0x4/0x30 [ipv6] [ 825.617019] softirqs last disabled at (7618): [] local_bh_disable+0x4/0x30 [ipv6] [ 825.617586] ---[ end trace 0000000000000000 ]--- Therefore, deal with the deadlock as suggested by [1], using the function drm_modeset_backoff(). [1] https://docs.kernel.org/gpu/drm-kms.html?highlight=kms#kms-locking Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug") Reported-by: Stefan Wahren Signed-off-by: Maíra Canal Tested-by: Stefan Wahren Signed-off-by: Maxime Ripard Link: https://patchwork.freedesktop.org/patch/msgid/20221229194638.178712-1-mcanal@igalia.com Signed-off-by: Sasha Levin

drm/vc4: dpi: Fix format mapping for RGB565

2023-03-10T08:33:09+00:00

[ Upstream commit 0870d86eac8a9abd89a0be1b719d5dc5bac936f0 ] The mapping is incorrect for RGB565_1X16 as it should be DPI_FORMAT_18BIT_666_RGB_1 instead of DPI_FORMAT_18BIT_666_RGB_3. Fixes: 08302c35b59d ("drm/vc4: Add DPI driver") Signed-off-by: Dave Stevenson Reviewed-by: Laurent Pinchart Link: https://lore.kernel.org/r/20221013-rpi-dpi-improvements-v3-7-eb76e26a772d@cerno.tech Signed-off-by: Maxime Ripard Signed-off-by: Sasha Levin

drm/vc4: Fix YUV plane handling when planes are in different buffers

2023-02-22T11:59:50+00:00

commit 6b77b16de75a6efc0870b1fa467209387cbee8f3 upstream. YUV images can either be presented as one allocation with offsets for the different planes, or multiple allocations with 0 offsets. The driver only ever calls drm_fb_[dma|cma]_get_gem_obj with plane index 0, therefore any application using the second approach was incorrectly rendered. Correctly determine the address for each plane, removing the assumption that the base address is the same for each. Fixes: fc04023fafec ("drm/vc4: Add support for YUV planes.") Signed-off-by: Dave Stevenson Signed-off-by: Maxime Ripard Link: https://patchwork.freedesktop.org/patch/msgid/20230127155708.454704-1-maxime@cerno.tech Signed-off-by: Greg Kroah-Hartman

drm/vc4: crtc: Increase setup cost in core clock calculation to handle extreme reduced blanking

2023-02-22T11:59:50+00:00

commit 247a631f9c0ffb37ed0786a94cb4c5f2b6fc7ab1 upstream. The formula that determines the core clock requirement based on pixel clock and blanking has been determined experimentally to minimise the clock while supporting all modes we've seen. A new reduced blanking mode (4kp60 at 533MHz rather than the standard 594MHz) has been seen that doesn't produce a high enough clock and results in "flip_done timed out" error. Increase the setup cost in the formula to make this work. The result is a reduced blanking mode increases by up to 7MHz while leaving the standard timing mode untouched Link: https://github.com/raspberrypi/linux/issues/4446 Fixes: 16e101051f32 ("drm/vc4: Increase the core clock based on HVS load") Signed-off-by: Dom Cobley Signed-off-by: Maxime Ripard Link: https://patchwork.freedesktop.org/patch/msgid/20230127145558.446123-1-maxime@cerno.tech Signed-off-by: Greg Kroah-Hartman

drm/vc4: hdmi: make CEC adapter name unique

2023-02-09T10:28:02+00:00

[ Upstream commit 51128c3f2a7c98055ea1d27e34910dc10977f618 ] The bcm2711 has two HDMI outputs, each with their own CEC adapter. The CEC adapter name has to be unique, but it is currently hardcoded to "vc4" for both outputs. Change this to use the card_name from the variant information in order to make the adapter name unique. Signed-off-by: Hans Verkuil Fixes: 15b4511a4af6 ("drm/vc4: add HDMI CEC support") Signed-off-by: Maxime Ripard Link: https://patchwork.freedesktop.org/patch/msgid/dcf1db75-d9cc-62cc-fa12-baf1b2b3bf31@xs4all.nl Signed-off-by: Sasha Levin