kernel/linux.git/drivers/gpu/drm/amd/display, branch v6.12.81

drm/amd/display: Correct logic check error for fastboot

2026-04-11T12:24:54+00:00

[ Upstream commit b6a65009e7ce3f0cc72da18f186adb60717b51a0 ] [Why] Fix fastboot broken in driver. This is caused by an open source backport change 7495962c. from the comment, the intended check is to disable fastboot for pre-DCN10. but the logic check is reversed, and causes fastboot to be disabled on all DCN10 and after. fastboot is for driver trying to pick up bios used hw setting and bypass reprogramming the hw if dc_validate_boot_timing() condition meets. Fixes: 7495962cbceb ("drm/amd/display: Disable fastboot on DCE 6 too") Cc: stable@vger.kernel.org Reviewed-by: Mario Limonciello Reviewed-by: Ovidiu Bunea Signed-off-by: Charlene Liu Signed-off-by: Ray Wu Tested-by: Daniel Wheeler Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Disable scaling on DCE6 for now

2026-04-11T12:24:54+00:00

[ Upstream commit 0e190a0446ec517666dab4691b296a9b758e590f ] Scaling doesn't work on DCE6 at the moment, the current register programming produces incorrect output when using fractional scaling (between 100-200%) on resolutions higher than 1080p. Disable it until we figure out how to program it properly. Fixes: 7c15fd86aaec ("drm/amd/display: dc/dce: add initial DCE6 support (v10)") Reviewed-by: Alex Deucher Signed-off-by: Timur Kristóf Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Adjust DCE 8-10 clock, don't overclock by 15%

2026-04-11T12:24:54+00:00

[ Upstream commit 1ae45b5d4f371af8ae51a3827d0ec9fe27eeb867 ] Adjust the nominal (and performance) clocks for DCE 8-10, and set them to 625 MHz, which is the value used by the legacy display code in amdgpu_atombios_get_clock_info. This was tested with Hawaii, Tonga and Fiji. These GPUs can output 4K 60Hz (10-bit depth) at 625 MHz. The extra 15% clock was added as a workaround for a Polaris issue which uses DCE 11, and should not have been used on DCE 8-10 which are already hardcoded to the highest possible display clock. Unfortunately, the extra 15% was mistakenly copied and kept even on code paths which don't affect Polaris. This commit fixes that and also adds a check to make sure not to exceed the maximum DCE 8-10 display clock. Fixes: 8cd61c313d8b ("drm/amd/display: Raise dispclk value for Polaris") Fixes: dc88b4a684d2 ("drm/amd/display: make clk mgr soc specific") Signed-off-by: Timur Kristóf Acked-by: Alex Deucher Reviewed-by: Rodrigo Siqueira Reviewed-by: Alex Hung Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Fix DCE 6.0 and 6.4 PLL programming.

2026-04-11T12:24:54+00:00

[ Upstream commit 35222b5934ec8d762473592ece98659baf6bc48e ] Apparently, both DCE 6.0 and 6.4 have 3 PLLs, but PLL0 can only be used for DP. Make sure to initialize the correct amount of PLLs in DC for these DCE versions and use PLL0 only for DP. Also, on DCE 6.0 and 6.4, the PLL0 needs to be powered on at initialization as opposed to DCE 6.1 and 7.x which use a different clock source for DFS. The following functions were used as reference from the old radeon driver implementation of DCE 6.x: - radeon_atom_pick_pll - atombios_crtc_set_disp_eng_pll Reviewed-by: Rodrigo Siqueira Reviewed-by: Alex Deucher Signed-off-by: Timur Kristóf Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Keep PLL0 running on DCE 6.0 and 6.4

2026-04-11T12:24:54+00:00

[ Upstream commit 0449726b58ea64ec96b95f95944f0a3650204059 ] DC can turn off the display clock when no displays are connected or when all displays are off, for reference see: - dce*_validate_bandwidth DC also assumes that the DP clock is always on and never powers it down, for reference see: - dce110_clock_source_power_down In case of DCE 6.0 and 6.4, PLL0 is the clock source for both the engine clock and DP clock, for reference see: - radeon_atom_pick_pll - atombios_crtc_set_disp_eng_pll Therefore, PLL0 should be always kept running on DCE 6.0 and 6.4. This commit achieves that by ensuring that by setting the display clock to the corresponding value in low power state instead of zero. This fixes a page flip timeout on SI with DC which happens when all connected displays are blanked. Signed-off-by: Timur Kristóf Reviewed-by: Alex Deucher Reviewed-by: Alex Hung Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Disable fastboot on DCE 6 too

2026-04-11T12:24:54+00:00

[ Upstream commit 7495962cbceb967e095233a5673ea71f3bcdee7e ] It already didn't work on DCE 8, so there is no reason to assume it would on DCE 6. Signed-off-by: Timur Kristóf Reviewed-by: Rodrigo Siqueira Reviewed-by: Alex Deucher Reviewed-by: Alex Hung Signed-off-by: Alex Deucher Signed-off-by: Rosen Penev Signed-off-by: Greg Kroah-Hartman

drm/amd/display: Do not skip unrelated mode changes in DSC validation

2026-04-02T11:09:39+00:00

[ Upstream commit aed3d041ab061ec8a64f50a3edda0f4db7280025 ] Starting with commit 17ce8a6907f7 ("drm/amd/display: Add dsc pre-validation in atomic check"), amdgpu resets the CRTC state mode_changed flag to false when recomputing the DSC configuration results in no timing change for a particular stream. However, this is incorrect in scenarios where a change in MST/DSC configuration happens in the same KMS commit as another (unrelated) mode change. For example, the integrated panel of a laptop may be configured differently (e.g., HDR enabled/disabled) depending on whether external screens are attached. In this case, plugging in external DP-MST screens may result in the mode_changed flag being dropped incorrectly for the integrated panel if its DSC configuration did not change during precomputation in pre_validate_dsc(). At this point, however, dm_update_crtc_state() has already created new streams for CRTCs with DSC-independent mode changes. In turn, amdgpu_dm_commit_streams() will never release the old stream, resulting in a memory leak. amdgpu_dm_atomic_commit_tail() will never acquire a reference to the new stream either, which manifests as a use-after-free when the stream gets disabled later on: BUG: KASAN: use-after-free in dc_stream_release+0x25/0x90 [amdgpu] Write of size 4 at addr ffff88813d836524 by task kworker/9:9/29977 Workqueue: events drm_mode_rmfb_work_fn Call Trace: dump_stack_lvl+0x6e/0xa0 print_address_description.constprop.0+0x88/0x320 ? dc_stream_release+0x25/0x90 [amdgpu] print_report+0xfc/0x1ff ? srso_alias_return_thunk+0x5/0xfbef5 ? __virt_addr_valid+0x225/0x4e0 ? dc_stream_release+0x25/0x90 [amdgpu] kasan_report+0xe1/0x180 ? dc_stream_release+0x25/0x90 [amdgpu] kasan_check_range+0x125/0x200 dc_stream_release+0x25/0x90 [amdgpu] dc_state_destruct+0x14d/0x5c0 [amdgpu] dc_state_release.part.0+0x4e/0x130 [amdgpu] dm_atomic_destroy_state+0x3f/0x70 [amdgpu] drm_atomic_state_default_clear+0x8ee/0xf30 ? drm_mode_object_put.part.0+0xb1/0x130 __drm_atomic_state_free+0x15c/0x2d0 atomic_remove_fb+0x67e/0x980 Since there is no reliable way of figuring out whether a CRTC has unrelated mode changes pending at the time of DSC validation, remember the value of the mode_changed flag from before the point where a CRTC was marked as potentially affected by a change in DSC configuration. Reset the mode_changed flag to this earlier value instead in pre_validate_dsc(). Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/5004 Fixes: 17ce8a6907f7 ("drm/amd/display: Add dsc pre-validation in atomic check") Signed-off-by: Yussuf Khalil Reviewed-by: Harry Wentland Signed-off-by: Alex Deucher (cherry picked from commit cc7c7121ae082b7b82891baa7280f1ff2608f22b) Signed-off-by: Sasha Levin

drm/amd: fix dcn 2.01 check

2026-03-25T10:08:57+00:00

[ Upstream commit 39f44f54afa58661ecae9c27e15f5dbce2372892 ] The ASICREV_IS_BEIGE_GOBY_P check always took precedence, because it includes all chip revisions upto NV_UNKNOWN. Fixes: 54b822b3eac3 ("drm/amd/display: Use dce_version instead of chip_id") Signed-off-by: Andy Nguyen Signed-off-by: Alex Deucher (cherry picked from commit 9c7be0efa6f0daa949a5f3e3fdf9ea090b0713cb) Signed-off-by: Sasha Levin

drm/amd/display: Fix DisplayID not-found handling in parse_edid_displayid_vrr()

2026-03-25T10:08:57+00:00

[ Upstream commit 2323b019651ad81c20a0f7f817c63392b3110652 ] parse_edid_displayid_vrr() searches the EDID extension blocks for a DisplayID extension before parsing the dynamic video timing range. The code previously checked whether edid_ext was NULL after the search loop. However, edid_ext is assigned during each iteration of the loop, so it will never be NULL once the loop has executed. If no DisplayID extension is found, edid_ext ends up pointing to the last extension block, and the NULL check does not correctly detect the failure case. Instead, check whether the loop completed without finding a matching DisplayID block by testing "i == edid->extensions". This ensures the function exits early when no DisplayID extension is present and avoids parsing an unrelated EDID extension block. Also simplify the EDID validation check using "!edid || !edid->extensions". Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:13079 parse_edid_displayid_vrr() warn: variable dereferenced before check 'edid_ext' (see line 13075) Fixes: a638b837d0e6 ("drm/amd/display: Fix refresh rate range for some panel") Cc: Roman Li Cc: Alex Hung Cc: Jerry Zuo Cc: Sun peng Li Cc: Tom Chung Cc: Dan Carpenter Cc: Aurabindo Pillai Signed-off-by: Srinivasan Shanmugam Reviewed-by: Tom Chung Signed-off-by: Alex Deucher (cherry picked from commit 91c7e6342e98c846b259c57273436fdea4c043f2) Signed-off-by: Sasha Levin

drm/amd/display: Wrap dcn32_override_min_req_memclk() in DC_FP_{START, END}

2026-03-25T10:08:49+00:00

commit ebe82c6e75cfc547154d0fd843b0dd6cca3d548f upstream. [Why] The dcn32_override_min_req_memclk function is in dcn32_fpu.c, which is compiled with CC_FLAGS_FPU into FP instructions. So when we call it we must use DC_FP_{START,END} to save and restore the FP context, and prepare the FP unit on architectures like LoongArch where the FP unit isn't always on. Reported-by: LiarOnce Fixes: ee7be8f3de1c ("drm/amd/display: Limit DCN32 8 channel or less parts to DPM1 for FPO") Signed-off-by: Xi Ruoyao Reviewed-by: Alex Hung Signed-off-by: Alex Deucher (cherry picked from commit 25bb1d54ba3983c064361033a8ec15474fece37e) Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman