kernel/linux.git/drivers/gnss, branch linux-4.20.y

gnss: sirf: fix premature wakeup interrupt enable

2019-03-10T06:10:15+00:00

commit 82f844c22588bf47132c82faeda50b6db473162c upstream. Make sure the receiver is powered (and booted) before enabling the wakeup interrupt to avoid spurious interrupts due to a floating input. Similarly, disable the interrupt before powering off on probe errors and on unbind. Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable # 4.19 Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: sirf: fix activation retry handling

2018-12-06T16:22:23+00:00

Fix activation helper which would return -ETIMEDOUT even if the last retry attempt was successful. Also change the semantics of the retries variable so that it actually holds the number of retries (rather than tries). Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable # 4.19 Signed-off-by: Johan Hovold

gnss: sirf: fix synchronous write timeout

2018-11-14T19:37:41+00:00

Passing a timeout of zero to the synchronous serdev_device_write() helper does currently not imply to wait forever (unlike passing zero to serdev_device_wait_until_sent()). Instead, if there's insufficient room in the write buffer, we'd end up with an incomplete write. Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers") Cc: stable # 4.19 Signed-off-by: Johan Hovold

gnss: serial: fix synchronous write timeout

2018-11-14T19:37:28+00:00

Passing a timeout of zero to the synchronous serdev_device_write() helper does currently not imply to wait forever (unlike passing zero to serdev_device_wait_until_sent()). Instead, if there's insufficient room in the write buffer, we'd end up with an incomplete write. Fixes: 37768b054f20 ("gnss: add generic serial driver") Cc: stable # 4.19 Signed-off-by: Johan Hovold

gnss: fix potential error pointer dereference

2018-07-16T10:48:07+00:00

The gnss_allocate_device() function returns a mix of NULL and error pointers on error. It should only return one or the other. Since the callers both check for NULL, I've modified it to return NULL on error. Fixes: 2b6a44035143 ("gnss: add GNSS receiver subsystem") Signed-off-by: Dan Carpenter Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: ubx: make struct ubx_gserial_ops static

2018-07-16T10:48:07+00:00

The structure ubx_gserial_ops is local to the source and does not need to be in global scope, so make it static. Cleans up sparse warning: symbol 'ubx_gserial_ops' was not declared. Should it be static? Signed-off-by: Colin Ian King Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: add receiver type support

2018-06-28T11:32:51+00:00

Add a "type" device attribute and a "GNSS_TYPE" uevent variable which can be used to determine the type of a GNSS receiver. The currently identified types reflect the protocol(s) supported by a receiver: "NMEA" NMEA 0183 "SiRF" SiRF Binary "UBX" UBX Note that both SiRF and UBX type receivers typically support a subset of NMEA 0183 with vendor extensions (e.g. to allow switching to the vendor protocol). Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: add driver for sirfstar-based receivers

2018-06-28T11:32:51+00:00

Add driver for serial-connected SiRFstar-based GNSS receivers. These devices typically boot into hibernate mode from which they can be woken using a pulse on the ON_OFF input pin. Once active, a pulse on the same ON_OFF pin is used to put the device back into hibernate mode. The current state can be determined by sampling the WAKEUP output. Hardware configurations where WAKEUP has been connected to ON_OFF (and where an initial WAKEUP pulse during boot is sufficient to have the device boot into active mode) are also supported. In this case, device power is managed using the main-supply regulator only. Note that configurations where WAKEUP is left not connected, so that the device power state can only indirectly be determined using the I/O interface, is currently not supported. It should be fairly straight-forward to extend the current implementation with such support however (and this this is the main reason for not using the generic serial implementation for this driver). Note that timepulse-support is left unimplemented. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: add driver for u-blox receivers

2018-06-28T11:31:32+00:00

Add driver for serial-connected u-blox GNSS receivers. Note that the driver uses the generic GNSS serial implementation and therefore essentially only manages power abstracted into three power states: ACTIVE, STANDBY, and OFF. For u-blox receivers with a main supply and no enable-gpios, this simply means that the main supply is disabled in STANDBY and OFF (the optional backup supply is kept enabled while the driver is bound). Note that timepulse-support is not yet implemented. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman

gnss: add generic serial driver

2018-06-28T11:31:32+00:00

Add a generic serial GNSS driver (library) which provides a common implementation for the gnss interface and power management (runtime and system suspend). This allows GNSS drivers for specific chip to be implemented by simply providing a set_power() callback to handle three states: ACTIVE, STANDBY and OFF. Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman