kernel/linux.git/drivers/clk/tegra, branch v4.19.112

clk: tegra: Mark fuse clock as critical

2020-02-11T12:34:11+00:00

commit bf83b96f87ae2abb1e535306ea53608e8de5dfbb upstream. For a little over a year, U-Boot on Tegra124 has configured the flow controller to perform automatic RAM re-repair on off->on power transitions of the CPU rail[1]. This is mandatory for correct operation of Tegra124. However, RAM re-repair relies on certain clocks, which the kernel must enable and leave running. The fuse clock is one of those clocks. Mark this clock as critical so that LP1 power mode (system suspend) operates correctly. [1] 3cc7942a4ae5 ARM: tegra: implement RAM repair Reported-by: Jonathan Hunter Cc: stable@vger.kernel.org Signed-off-by: Stephen Warren Signed-off-by: Thierry Reding Signed-off-by: Greg Kroah-Hartman

clk: tegra20: Turn EMC clock gate into divider

2019-12-01T08:17:28+00:00

[ Upstream commit 514fddba845ed3a1b17e01e99cb3a2a52256a88a ] Kernel should never gate the EMC clock as it causes immediate lockup, so removing clk-gate functionality doesn't affect anything. Turning EMC clk gate into divider allows to implement glitch-less EMC scaling, avoiding reparenting to a backup clock. Signed-off-by: Dmitry Osipenko Acked-by: Peter De Schrijver Acked-by: Stephen Boyd Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin

clk: tegra: Fixes for MBIST work around

2019-12-01T08:16:27+00:00

[ Upstream commit a4dbbceeee3e0ba670875a147237d6566de78840 ] Fix some incorrect data in LVL2 offset and bit mask. Fixes: e403d0057343 ("clk: tegra: MBIST work around for Tegra210") Signed-off-by: Joseph Lo Signed-off-by: Peter De Schrijver Acked-by: Jon Hunter Acked-by: Peter De Schrijver Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra210: Fix default rates for HDA clocks

2019-09-16T06:22:16+00:00

[ Upstream commit 9caec6620f25b6d15646bbdb93062c872ba3b56f ] Currently the default clock rates for the HDA and HDA2CODEC_2X clocks are both 19.2MHz. However, the default rates for these clocks should actually be 51MHz and 48MHz, respectively. The current clock settings results in a distorted output during audio playback. Correct the default clock rates for these clocks by specifying them in the clock init table for Tegra210. Cc: stable@vger.kernel.org Signed-off-by: Jon Hunter Acked-by: Thierry Reding Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra: Fix maximum audio sync clock for Tegra124/210

2019-09-16T06:22:16+00:00

[ Upstream commit 845d782d91448e0fbca686bca2cc9f9c2a9ba3e7 ] The maximum frequency supported for I2S on Tegra124 and Tegra210 is 24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the Jetson TX1 module data sheet for Tegra210). However, the maximum I2S frequency is limited to 24MHz because that is the maximum frequency of the audio sync clock. Increase the maximum audio sync clock frequency to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz for I2S. Update the tegra_clk_register_sync_source() function so that it does not set the initial rate for the sync clocks and use the clock init tables to set the initial rate instead. Signed-off-by: Jon Hunter Acked-by: Thierry Reding Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra210: fix PLLU and PLLU_OUT1

2019-08-06T17:06:48+00:00

[ Upstream commit 0d34dfbf3023cf119b83f6470692c0b10c832495 ] Full-speed and low-speed USB devices do not work with Tegra210 platforms because of incorrect PLLU/PLLU_OUT1 clock settings. When full-speed device is connected: [ 14.059886] usb 1-3: new full-speed USB device number 2 using tegra-xusb [ 14.196295] usb 1-3: device descriptor read/64, error -71 [ 14.436311] usb 1-3: device descriptor read/64, error -71 [ 14.675749] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 14.812335] usb 1-3: device descriptor read/64, error -71 [ 15.052316] usb 1-3: device descriptor read/64, error -71 [ 15.164799] usb usb1-port3: attempt power cycle When low-speed device is connected: [ 37.610949] usb usb1-port3: Cannot enable. Maybe the USB cable is bad? [ 38.557376] usb usb1-port3: Cannot enable. Maybe the USB cable is bad? [ 38.564977] usb usb1-port3: attempt power cycle This commit fixes the issue by: 1. initializing PLLU_OUT1 before initializing XUSB_FS_SRC clock because PLLU_OUT1 is parent of XUSB_FS_SRC. 2. changing PLLU post-divider to /2 (DIVP=1) according to Technical Reference Manual. Fixes: e745f992cf4b ("clk: tegra: Rework pll_u") Signed-off-by: JC Kuo Acked-By: Peter De Schrijver Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra: Fix PLLM programming on Tegra124+ when PMC overrides divider

2019-05-25T16:23:29+00:00

commit 40db569d6769ffa3864fd1b89616b1a7323568a8 upstream. There are wrongly set parenthesis in the code that are resulting in a wrong configuration being programmed for PLLM. The original fix was made by Danny Huang in the downstream kernel. The patch was tested on Nyan Big Tegra124 chromebook, PLLM rate changing works correctly now and system doesn't lock up after changing the PLLM rate due to EMC scaling. Cc: Tested-by: Steev Klimaszewski Signed-off-by: Dmitry Osipenko Acked-By: Peter De Schrijver Signed-off-by: Stephen Boyd Signed-off-by: Greg Kroah-Hartman

clk: tegra: dfll: Fix a potential Oop in remove()

2019-03-05T16:58:46+00:00

[ Upstream commit d39eca547f3ec67140a5d765a426eb157b978a59 ] If tegra_dfll_unregister() fails then "soc" is an error pointer. We should just return instead of dereferencing it. Fixes: 1752c9ee23fb ("clk: tegra: dfll: Fix drvdata overwriting issue") Signed-off-by: Dan Carpenter Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

Merge branches 'clk-imx6-ocram', 'clk-missing-put', 'clk-tegra-sdmmc-jitter', 'clk-allwinner' and 'clk-uniphier' into clk-next

2018-08-15T05:58:53+00:00

* clk-imx6-ocram: : - i.MX6SX ocram_s clk support clk: imx: add ocram_s clock for i.mx6sx * clk-missing-put: : - Add missing of_node_put()s in some i.MX clk drivers clk: imx6sll: fix missing of_node_put() clk: imx6ul: fix missing of_node_put() * clk-tegra-sdmmc-jitter: : - Tegra SDMMC clk jitter improvements with high speed signaling modes clk: tegra: make sdmmc2 and sdmmc4 as sdmmc clocks clk: tegra: Add sdmmc mux divider clock clk: tegra: Refactor fractional divider calculation clk: tegra: Fix includes required by fence_udelay() * clk-allwinner: clk: sunxi-ng: add A64 compatible string dt-bindings: add compatible string for the A64 DE2 CCU clk: sunxi-ng: r40: Export video PLLs clk: sunxi-ng: r40: Allow setting parent rate to display related clocks clk: sunxi-ng: r40: Add minimal rate for video PLLs * clk-uniphier: : - Uniphier NAND, USB3 PHY, and SPI clk support clk: uniphier: add clock frequency support for SPI clk: uniphier: add more USB3 PHY clocks clk: uniphier: add NAND 200MHz clock

Merge branches 'clk-imx-critical', 'clk-tegra-bpmp', 'clk-tegra-124', 'clk-tegra-critical' and 'clk-tegra-emc-oob' into clk-next

2018-08-15T05:58:42+00:00

* clk-imx-critical: : - Convert to CLK_IS_CRITICAL for i.MX51/53 driver clk: imx51-imx53: Include sizes.h to silence compile errors clk: imx51-imx53: Annotate critical clocks as CLK_IS_CRITICAL * clk-tegra-bpmp: : - Fix Tegra BPMP driver oops when some xlating a NULL clk clk: tegra: bpmp: Don't crash when a clock fails to register * clk-tegra-124: : - Proper default configuration for vic03 and vde clks on Tegra124 clk: tegra: Make vde a child of pll_c3 clk: tegra: Make vic03 a child of pll_c3 * clk-tegra-critical: : - Mark Tegra memory controller clks as critical clk: tegra: Mark Memory Controller clock as critical * clk-tegra-emc-oob: : - Fix array bounds clamp in Tegra's emc determine_rate() op clk: tegra: emc: Avoid out-of-bounds bug