kernel/linux.git/drivers/clk/tegra, branch v4.14.286

clk: tegra: tegra124-emc: Fix missing put_device() call in emc_ensure_emc_driver

2022-04-20T07:08:20+00:00

[ Upstream commit 6d6ef58c2470da85a99119f74d34216c8074b9f0 ] The reference taken by 'of_find_device_by_node()' must be released when not needed anymore. Add the corresponding 'put_device()' in the error handling path. Fixes: 2db04f16b589 ("clk: tegra: Add EMC clock driver") Signed-off-by: Miaoqian Lin Acked-by: Thierry Reding Link: https://lore.kernel.org/r/20220112104501.30655-1-linmq006@gmail.com Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra: Ensure that PLLU configuration is applied properly

2021-07-20T14:17:43+00:00

[ Upstream commit a7196048cd5168096c2c4f44a3939d7a6dcd06b9 ] The PLLU (USB) consists of the PLL configuration itself and configuration of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114, where T114 immediately bails out if PLLU is enabled and T30 re-enables a potentially already enabled PLL (left after bootloader) and then fully reprograms it, which could be unsafe to do. The correct way should be to skip enabling of the PLL if it's already enabled and then apply configuration to the outputs. This patch doesn't fix any known problems, it's a minor improvement. Acked-by: Thierry Reding Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin

clk: tegra: Fix duplicated SE clock entry

2020-12-29T12:47:01+00:00

[ Upstream commit 5bf5861d6ea6c3f4b38fc8fda2062b2dc44ac63d ] The periph_clks[] array contains duplicated entry for Security Engine clock which was meant to be defined for T210, but it wasn't added properly. This patch corrects the T210 SE entry and fixes the following error message on T114/T124: "Tegra clk 127: register failed with -17". Fixes: dc37fec48314 ("clk: tegra: periph: Add new periph clks and muxes for Tegra210") Tested-by Nicolas Chauvet Reported-by Nicolas Chauvet Signed-off-by: Dmitry Osipenko Link: https://lore.kernel.org/r/20201025224212.7790-1-digetx@gmail.com Acked-by: Thierry Reding Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra: Fix Tegra PMC clock out parents

2020-04-24T06:01:18+00:00

[ Upstream commit 6fe38aa8cac3a5db38154331742835a4d9740788 ] Tegra PMC clocks clk_out_1, clk_out_2, and clk_out_3 supported parents are osc, osc_div2, osc_div4 and extern clock. Clock driver is using incorrect parents clk_m, clk_m_div2, clk_m_div4 for PMC clocks. This patch fixes this. Tested-by: Dmitry Osipenko Reviewed-by: Dmitry Osipenko Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin

clk: tegra: Mark fuse clock as critical

2020-02-14T21:32:16+00:00

commit bf83b96f87ae2abb1e535306ea53608e8de5dfbb upstream. For a little over a year, U-Boot on Tegra124 has configured the flow controller to perform automatic RAM re-repair on off->on power transitions of the CPU rail[1]. This is mandatory for correct operation of Tegra124. However, RAM re-repair relies on certain clocks, which the kernel must enable and leave running. The fuse clock is one of those clocks. Mark this clock as critical so that LP1 power mode (system suspend) operates correctly. [1] 3cc7942a4ae5 ARM: tegra: implement RAM repair Reported-by: Jonathan Hunter Cc: stable@vger.kernel.org Signed-off-by: Stephen Warren Signed-off-by: Thierry Reding Signed-off-by: Greg Kroah-Hartman

clk: tegra210: fix PLLU and PLLU_OUT1

2019-08-06T17:05:21+00:00

[ Upstream commit 0d34dfbf3023cf119b83f6470692c0b10c832495 ] Full-speed and low-speed USB devices do not work with Tegra210 platforms because of incorrect PLLU/PLLU_OUT1 clock settings. When full-speed device is connected: [ 14.059886] usb 1-3: new full-speed USB device number 2 using tegra-xusb [ 14.196295] usb 1-3: device descriptor read/64, error -71 [ 14.436311] usb 1-3: device descriptor read/64, error -71 [ 14.675749] usb 1-3: new full-speed USB device number 3 using tegra-xusb [ 14.812335] usb 1-3: device descriptor read/64, error -71 [ 15.052316] usb 1-3: device descriptor read/64, error -71 [ 15.164799] usb usb1-port3: attempt power cycle When low-speed device is connected: [ 37.610949] usb usb1-port3: Cannot enable. Maybe the USB cable is bad? [ 38.557376] usb usb1-port3: Cannot enable. Maybe the USB cable is bad? [ 38.564977] usb usb1-port3: attempt power cycle This commit fixes the issue by: 1. initializing PLLU_OUT1 before initializing XUSB_FS_SRC clock because PLLU_OUT1 is parent of XUSB_FS_SRC. 2. changing PLLU post-divider to /2 (DIVP=1) according to Technical Reference Manual. Fixes: e745f992cf4b ("clk: tegra: Rework pll_u") Signed-off-by: JC Kuo Acked-By: Peter De Schrijver Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin

clk: tegra: Fix PLLM programming on Tegra124+ when PMC overrides divider

2019-05-25T16:25:20+00:00

commit 40db569d6769ffa3864fd1b89616b1a7323568a8 upstream. There are wrongly set parenthesis in the code that are resulting in a wrong configuration being programmed for PLLM. The original fix was made by Danny Huang in the downstream kernel. The patch was tested on Nyan Big Tegra124 chromebook, PLLM rate changing works correctly now and system doesn't lock up after changing the PLLM rate due to EMC scaling. Cc: Tested-by: Steev Klimaszewski Signed-off-by: Dmitry Osipenko Acked-By: Peter De Schrijver Signed-off-by: Stephen Boyd Signed-off-by: Greg Kroah-Hartman

clk: tegra: bpmp: Don't crash when a clock fails to register

2018-09-26T06:38:13+00:00

[ Upstream commit f7b3182232c82bb9769e2d5471d702bae2972d2b ] When registering clocks, we just skip any that fail to register (leaving a NULL hole in the clock table). However, our of_xlate function still tries to dereference each entry while looking for the clock with the requested id, causing a crash if any clocks failed to register. Add a check to of_xlate to skip any NULL clocks. Signed-off-by: Mikko Perttunen Acked-by: Jon Hunter Signed-off-by: Stephen Boyd Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

clk: tegra: Fix pll_u rate configuration

2018-05-25T14:17:53+00:00

[ Upstream commit c35b518f9ba06c9de79fb3ff62eed7462d804995 ] Turns out latest upstream U-Boot does not configure/enable pll_u which leaves it at some default rate of 500 kHz: root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u pll_u 3 3 0 500000 0 Of course this won't quite work leading to the following messages: [ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra- ehci [ 11.759173] usb 2-1: device descriptor read/64, error -110 [ 27.119453] usb 2-1: device descriptor read/64, error -110 [ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra- ehci [ 32.559454] usb 2-1: device descriptor read/64, error -110 [ 47.929777] usb 2-1: device descriptor read/64, error -110 [ 48.049658] usb usb2-port1: attempt power cycle [ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra- ehci [ 59.349457] usb 2-1: device not accepting address 4, error -110 [ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra- ehci [ 70.069457] usb 2-1: device not accepting address 5, error -110 [ 70.079721] usb usb2-port1: unable to enumerate USB device Fix this by actually allowing the rate also being set from within the Linux kernel. Signed-off-by: Marcel Ziswiler Tested-by: Jon Hunter Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

clk: tegra: Fix cclk_lp divisor register

2017-12-20T09:10:28+00:00

[ Upstream commit 54eff2264d3e9fd7e3987de1d7eba1d3581c631e ] According to comments in code and common sense, cclk_lp uses its own divisor, not cclk_g's. Fixes: b08e8c0ecc42 ("clk: tegra: add clock support for Tegra30") Signed-off-by: Michał Mirosław Acked-By: Peter De Schrijver Signed-off-by: Thierry Reding Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman