kernel/linux.git/drivers/bluetooth, branch linux-7.0.y

Bluetooth: btmtk: fix urb->setup_packet leak in error paths

2026-06-01T15:54:51+00:00

[ Upstream commit dd1dda6b8d6e1f4376a5b3055a04f0ecbdb4d6bd ] The setup_packet of control urb is not freed if usb_submit_urb fails or the submitted urb is killed. Add free in these two paths. Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Jiajia Liu Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Sasha Levin

Bluetooth: btintel_pcie: Fix incorrect MAC access programming

2026-06-01T15:54:51+00:00

[ Upstream commit 88365d04fdc821dc4e9eb0cc00fdf6905430d172 ] btintel_pcie_get_mac_access() and btintel_pcie_release_mac_access() were programming STOP_MAC_ACCESS_DIS and XTAL_CLK_REQ in addition to the MAC_ACCESS_REQ handshake. These bits are not part of the host MAC-access handshake on the supported parts; the driver was programming them incorrectly. Drop the writes so the register update contains only the bits the controller actually consumes. Fixes: b9465e6670a2 ("Bluetooth: btintel_pcie: Read hardware exception data") Signed-off-by: Kiran K Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Sasha Levin

Bluetooth: hci_qca: Convert timeout from jiffies to ms

2026-06-01T15:54:22+00:00

commit 375ba7484132662a4a8c7547d088fb6275c00282 upstream. Since the timer uses jiffies as its unit rather than ms, the timeout value must be converted from ms to jiffies when configuring the timer. Otherwise, the intended 8s timeout is incorrectly set to approximately 33s. To improve readability, embed msecs_to_jiffies() directly in the macro definitions and drop the _MS suffix from macros that now yield jiffies values: MEMDUMP_TIMEOUT, FW_DOWNLOAD_TIMEOUT, IBS_DISABLE_SSR_TIMEOUT, CMD_TRANS_TIMEOUT, and IBS_BTSOC_TX_IDLE_TIMEOUT. IBS_WAKE_RETRANS_TIMEOUT_MS and IBS_HOST_TX_IDLE_TIMEOUT_MS are intentionally left unchanged. Their values are stored in the struct fields wake_retrans and tx_idle_delay, which hold ms values at runtime and can be modified via debugfs. The msecs_to_jiffies() conversion happens at each call site against the field value, so it cannot be embedded in the macro. Wake timer depends on commit c347ca17d62a Cc: stable@vger.kernel.org Fixes: d841502c79e3 ("Bluetooth: hci_qca: Collect controller memory dump during SSR") Reviewed-by: Paul Menzel Acked-by: Bartosz Golaszewski Signed-off-by: Shuai Zhang Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths

2026-06-01T15:54:22+00:00

commit c1bb9336ae6b54a5f6a353c4bd4ed9a4307e429b upstream. Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer Dereference (NPD) conditions were observed in the lifecycle management of hci_uart. The primary issue arises because the workqueues (init_ready and write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY flag is set during TTY close. If a hangup occurs before setup completes, hci_uart_tty_close() skips the teardown of these workqueues and proceeds to free the `hu` struct. When the scheduled work executes later, it blindly dereferences the freed `hu` struct. Furthermore, several data races and UAFs were identified in the teardown sequence: 1. Calling hci_uart_flush() from hci_uart_close() without effectively disabling write_work causes a race condition where both can concurrently double-free hu->tx_skb. This happens because protocol timers can concurrently invoke hci_uart_tx_wakeup() and requeue write_work. 2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF when vendor specific protocol close callbacks dereference hu->hdev. 3. In the initialization error paths, failing to take the proto_lock write lock before clearing PROTO_READY leads to races with active readers. Additionally, hci_uart_tty_receive() accesses hu->hdev outside the read lock, leading to UAFs if the initialization error path frees hdev concurrently. Fix these synchronization and lifecycle issues by: 1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first, followed immediately by a cancel_work_sync(&hu->write_work). Clearing the flag locks out concurrent protocol timers from successfully invoking hci_uart_tx_wakeup(), effectively rendering the cancellation permanent and preventing the tx_skb double-free. 2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip hu->proto->flush(). This is perfectly safe in the tty_close path because hu->proto->close() executes shortly after, which intrinsically purges all protocol SKB queues and tears down the state. 3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev) across all close and error paths to prevent vendor-level UAFs. 4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive() inside the proto_lock read-side critical section to safely synchronize with device unregistration. 5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely flush the workqueue before hci_uart_flush() is invoked via the HCI core. 6. Utilizing cancel_work_sync() instead of disable_work_sync() across all paths to prevent permanently breaking user-space retry capabilities. Fixes: 3b799254cf6f ("Bluetooth: hci_uart: Cancel init work before unregistering") Cc: stable@vger.kernel.org Signed-off-by: Mingyu Wang <25181214217@stu.xidian.edu.cn> Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: btmtk: accept too short WMT FUNC_CTRL events

2026-05-23T11:09:38+00:00

commit e3ac0d9f1a205f33a43fba3b79ef74d2f604c78b upstream. MT7925 (USB ID 0e8d:e025) on fw version 20260106153314 sends WMT FUNC_CTRL events that are missing the status field. Prior to commit 006b9943b982 ("Bluetooth: btmtk: validate WMT event SKB length before struct access") the status was read from out-of-bounds of SKB data, which usually would result to success with BTMTK_WMT_ON_UNDONE, although I don't know the intent here. The bounds check added in that commit returns with error instead, producing "Bluetooth: hci0: Failed to send wmt func ctrl (-22)" and makes the device unusable. Fix the regression by interpreting too short packet as status BTMTK_WMT_ON_UNDONE, which makes the device work normally again. Fixes: 634a4408c061 ("Bluetooth: btmtk: validate WMT event SKB length before struct access") Signed-off-by: Pauli Virtanen Tested-by: Mikhail Gavrilov # MT7922 (0489:e0e2) Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_ldisc: Clear HCI_UART_PROTO_INIT on error

2026-05-23T11:08:40+00:00

[ Upstream commit 68d39ea5e0adc9ecaea1ce8abd842ec972eb8718 ] When hci_register_dev() fails in hci_uart_register_dev() HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu) and setting hu->hdev to NULL. This means incoming UART data will reach the protocol-specific recv handler in hci_uart_tty_receive() after resources are freed. Clear HCI_UART_PROTO_INIT with a write lock before calling hu->proto->close() and setting hu->hdev to NULL. The write lock ensures all active readers have completed and no new reader can enter the protocol recv path before resources are freed. This allows the protocol-specific recv functions to remove the "HCI_UART_REGISTERED" guard without risking a null pointer dereference if hci_register_dev() fails. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Signed-off-by: Jonathan Rissanen Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Sasha Levin

Bluetooth: btmtk: validate WMT event SKB length before struct access

2026-05-14T13:31:06+00:00

commit 634a4408c0615c523cf7531790f4f14a422b9206 upstream. btmtk_usb_hci_wmt_sync() casts the WMT event response SKB data to struct btmtk_hci_wmt_evt (7 bytes) and struct btmtk_hci_wmt_evt_funcc (9 bytes) without first checking that the SKB contains enough data. A short firmware response causes out-of-bounds reads from SKB tailroom. Use skb_pull_data() to validate and advance past the base WMT event header. For the FUNC_CTRL case, pull the additional status field bytes before accessing them. Fixes: d019930b0049 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c") Cc: stable@vger.kernel.org Signed-off-by: Tristan Madani Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: virtio_bt: validate rx pkt_type header length

2026-05-14T13:31:06+00:00

commit daf23014e5d975e72ea9c02b5160d3fcf070ea47 upstream. virtbt_rx_handle() reads the leading pkt_type byte from the RX skb and forwards the remainder to hci_recv_frame() for every event/ACL/SCO/ISO type, without checking that the remaining payload is at least the fixed HCI header for that type. After the preceding patch bounds the backend-supplied used.len to [1, VIRTBT_RX_BUF_SIZE], a one-byte completion still reaches hci_recv_frame() with skb->len already pulled to 0. If the byte happened to be HCI_ACLDATA_PKT, the ACL-vs-ISO classification fast-path in hci_dev_classify_pkt_type() dereferences hci_acl_hdr(skb)->handle whenever the HCI device has an active CIS_LINK, BIS_LINK, or PA_LINK connection, reading two bytes of uninitialized RX-buffer data. The same hazard exists for every packet type the driver accepts because none of the switch cases in virtbt_rx_handle() check skb->len against the per-type minimum HCI header size before handing the frame to the core. After stripping pkt_type, require skb->len to cover the fixed header size for the selected type (event 2, ACL 4, SCO 3, ISO 4) before calling hci_recv_frame(); drop ratelimited otherwise. Unknown pkt_type values still take the original kfree_skb() default path. Use bt_dev_err_ratelimited() because both the length and pkt_type values come from an untrusted backend that can otherwise flood the kernel log. Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length") Cc: stable@vger.kernel.org Cc: Soenke Huster Signed-off-by: Michael Bommarito Assisted-by: Claude:claude-opus-4-7 Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: virtio_bt: clamp rx length before skb_put

2026-05-14T13:31:06+00:00

commit 21bd244b6de5d2fe1063c23acc93fbdd2b20d112 upstream. virtbt_rx_work() calls skb_put(skb, len) where len comes directly from virtqueue_get_buf() with no validation against the buffer we posted to the device. The RX skb is allocated in virtbt_add_inbuf() and exposed to virtio as exactly 1000 bytes via sg_init_one(). Checking len against skb_tailroom(skb) is not sufficient because alloc_skb() can leave more tailroom than the 1000 bytes actually handed to the device. A malicious or buggy backend can therefore report used.len between 1001 and skb_tailroom(skb), causing skb_put() to include uninitialized kernel heap bytes that were never written by the device. The same path also accepts len == 0, in which case skb_put(skb, 0) leaves the skb empty but virtbt_rx_handle() still reads the pkt_type byte from skb->data, consuming uninitialized memory. Define VIRTBT_RX_BUF_SIZE once and reuse it in alloc_skb() and sg_init_one(), and gate virtbt_rx_work() on that same constant so the bound checked matches the buffer actually exposed to the device. Reject used.len == 0 in the same gate so an empty completion can no longer reach virtbt_rx_handle(). Use bt_dev_err_ratelimited() because the length value comes from an untrusted backend that can otherwise flood the kernel log. Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer overflow in USB transport layer"), which hardened the USB 9p transport against unchecked device-reported length. Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length") Cc: stable@vger.kernel.org Cc: Soenke Huster Signed-off-by: Michael Bommarito Assisted-by: Claude:claude-opus-4-7 Signed-off-by: Luiz Augusto von Dentz Signed-off-by: Greg Kroah-Hartman

Bluetooth: hci_h4: Fix race during initialization

2026-04-01T20:45:47+00:00

Commit 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") fixed a race for hci commands sent during initialization. However, there is still a race that happens if an hci event from one of these commands is received before HCI_UART_REGISTERED has been set at the end of hci_uart_register_dev(). The event will be ignored which causes the command to fail with a timeout in the log: "Bluetooth: hci0: command 0x1003 tx timeout" This is because the hci event receive path (hci_uart_tty_receive -> h4_recv) requires HCI_UART_REGISTERED to be set in h4_recv(), while the hci command transmit path (hci_uart_send_frame -> h4_enqueue) only requires HCI_UART_PROTO_INIT to be set in hci_uart_send_frame(). The check for HCI_UART_REGISTERED was originally added in commit c2578202919a ("Bluetooth: Fix H4 crash from incoming UART packets") to fix a crash caused by hu->hdev being null dereferenced. That can no longer happen: once HCI_UART_PROTO_INIT is set in hci_uart_register_dev() all pointers (hu, hu->priv and hu->hdev) are valid, and hci_uart_tty_receive() already calls h4_recv() on HCI_UART_PROTO_INIT or HCI_UART_PROTO_READY. Remove the check for HCI_UART_REGISTERED in h4_recv() to fix the race condition. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Signed-off-by: Jonathan Rissanen Signed-off-by: Luiz Augusto von Dentz