kernel/linux.git/drivers/ata, branch v4.4.171

libata: whitelist all SAMSUNG MZ7KM* solid-state disks

2018-12-21T13:09:53+00:00

[ Upstream commit fd6f32f78645db32b6b95a42e45da2ddd6de0e67 ] These devices support read zero after trim (RZAT), as they advertise to the OS. However, the OS doesn't believe the SSDs unless they are explicitly whitelisted. Acked-by: Martin K. Petersen Signed-off-by: Juha-Matti Tilli Signed-off-by: Jens Axboe Signed-off-by: Sasha Levin

ahci: don't ignore result code of ahci_reset_controller()

2018-11-10T15:41:42+00:00

[ Upstream commit d312fefea8387503375f728855c9a62de20c9665 ] ahci_pci_reset_controller() calls ahci_reset_controller(), which may fail, but ignores the result code and always returns success. This may result in failures like below ahci 0000:02:00.0: version 3.0 ahci 0000:02:00.0: enabling device (0000 -> 0003) ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled ahci 0000:02:00.0: controller reset failed (0xffffffff) ahci 0000:02:00.0: failed to stop engine (-5) ... repeated many times ... ahci 0000:02:00.0: failed to stop engine (-5) Unable to handle kernel paging request at virtual address ffff0000093f9018 ... PC is at ahci_stop_engine+0x5c/0xd8 [libahci] LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci] ... [] ahci_stop_engine+0x5c/0xd8 [libahci] [] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci] [] ahci_init_controller+0x80/0x168 [libahci] [] ahci_pci_init_controller+0x60/0x68 [ahci] [] ahci_init_one+0x75c/0xd88 [ahci] [] local_pci_probe+0x3c/0xb8 [] pci_device_probe+0x138/0x170 [] driver_probe_device+0x2dc/0x458 [] __driver_attach+0x114/0x118 [] bus_for_each_dev+0x60/0xa0 [] driver_attach+0x20/0x28 [] bus_add_driver+0x1f0/0x2a8 [] driver_register+0x60/0xf8 [] __pci_register_driver+0x3c/0x48 [] ahci_pci_driver_init+0x1c/0x1000 [ahci] [] do_one_initcall+0x38/0x120 where an obvious hardware level failure results in an unnecessary 15 second delay and a subsequent crash. So record the result code of ahci_reset_controller() and relay it, rather than ignoring it. Signed-off-by: Ard Biesheuvel Signed-off-by: Tejun Heo Signed-off-by: Sasha Levin

ata: libahci: Correct setting of DEVSLP register

2018-09-19T20:48:58+00:00

[ Upstream commit 2dbb3ec29a6c069035857a2fc4c24e80e5dfe3cc ] We have seen that on some platforms, SATA device never show any DEVSLP residency. This prevent power gating of SATA IP, which prevent system to transition to low power mode in systems with SLP_S0 aka modern standby systems. The PHY logic is off only in DEVSLP not in slumber. Reference: https://www.intel.com/content/dam/www/public/us/en/documents/datasheets /332995-skylake-i-o-platform-datasheet-volume-1.pdf Section 28.7.6.1 Here driver is trying to do read-modify-write the devslp register. But not resetting the bits for which this driver will modify values (DITO, MDAT and DETO). So simply reset those bits before updating to new values. Signed-off-by: Srinivas Pandruvada Reviewed-by: Rafael J. Wysocki Reviewed-by: Hans de Goede Signed-off-by: Tejun Heo Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

libata: Fix command retry decision

2018-08-06T14:24:36+00:00

[ Upstream commit 804689ad2d9b66d0d3920b48cf05881049d44589 ] For failed commands with valid sense data (e.g. NCQ commands), scsi_check_sense() is used in ata_analyze_tf() to determine if the command can be retried. In such case, rely on this decision and ignore the command error mask based decision done in ata_worth_retry(). This fixes useless retries of commands such as unaligned writes on zoned disks (TYPE_ZAC). Signed-off-by: Damien Le Moal Reviewed-by: Hannes Reinecke Signed-off-by: Tejun Heo Signed-off-by: Sasha Levin Signed-off-by: Greg Kroah-Hartman

ahci: Disable LPM on Lenovo 50 series laptops with a too old BIOS

2018-07-17T09:31:43+00:00

commit 240630e61870e62e39a97225048f9945848fa5f5 upstream. There have been several reports of LPM related hard freezes about once a day on multiple Lenovo 50 series models. Strange enough these reports where not disk model specific as LPM issues usually are and some users with the exact same disk + laptop where seeing them while other users where not seeing these issues. It turns out that enabling LPM triggers a firmware bug somewhere, which has been fixed in later BIOS versions. This commit adds a new ahci_broken_lpm() function and a new ATA_FLAG_NO_LPM for dealing with this. The ahci_broken_lpm() function contains DMI match info for the 4 models which are known to be affected by this and the DMI BIOS date field for known good BIOS versions. If the BIOS date is older then the one in the table LPM will be disabled and a warning will be printed. Note the BIOS dates are for known good versions, some older versions may work too, but we don't know for sure, the table is using dates from BIOS versions for which users have confirmed that upgrading to that version makes the problem go away. Unfortunately I've been unable to get hold of the reporter who reported that BIOS version 2.35 fixed the problems on the W541 for him. I've been able to verify the DMI_SYS_VENDOR and DMI_PRODUCT_VERSION from an older dmidecode, but I don't know the exact BIOS date as reported in the DMI. Lenovo keeps a changelog with dates in their release notes, but the dates there are the release dates not the build dates which are in DMI. So I've chosen to set the date to which we compare to one day past the release date of the 2.34 BIOS. I plan to fix this with a follow up commit once I've the necessary info. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman

libata: Drop SanDisk SD7UB3Q*G1001 NOLPM quirk

2018-07-03T09:21:26+00:00

commit 2cfce3a86b64b53f0a70e92a6a659c720c319b45 upstream. Commit 184add2ca23c ("libata: Apply NOLPM quirk for SanDisk SD7UB3Q*G1001 SSDs") disabled LPM for SanDisk SD7UB3Q*G1001 SSDs. This has lead to several reports of users of that SSD where LPM was working fine and who know have a significantly increased idle power consumption on their laptops. Likely there is another problem on the T450s from the original reporter which gets exposed by the uncore reaching deeper sleep states (higher PC-states) due to LPM being enabled. The problem as reported, a hardfreeze about once a day, already did not sound like it would be caused by LPM and the reports of the SSD working fine confirm this. The original reporter is ok with dropping the quirk. A X250 user has reported the same hard freeze problem and for him the problem went away after unrelated updates, I suspect some GPU driver stack changes fixed things. TL;DR: The original reporters problem were triggered by LPM but not an LPM issue, so drop the quirk for the SSD in question. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1583207 Cc: stable@vger.kernel.org Cc: Richard W.M. Jones Cc: Lorenzo Dalrio Reported-by: Lorenzo Dalrio Signed-off-by: Hans de Goede Signed-off-by: Tejun Heo Acked-by: "Richard W.M. Jones" Signed-off-by: Greg Kroah-Hartman

libata: zpodd: small read overflow in eject_tray()

2018-07-03T09:21:26+00:00

commit 18c9a99bce2a57dfd7e881658703b5d7469cc7b9 upstream. We read from the cdb[] buffer in ata_exec_internal_sg(). It has to be ATAPI_CDB_LEN (16) bytes long, but this buffer is only 12 bytes. Fixes: 213342053db5 ("libata: handle power transition of ODD") Signed-off-by: Dan Carpenter Signed-off-by: Tejun Heo Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman

libata: zpodd: make arrays cdb static, reduces object code size

2018-07-03T09:21:26+00:00

commit 795ef788145ed2fa023efdf11e8d5d7bedc21462 upstream. Don't populate the arrays cdb on the stack, instead make them static. Makes the object code smaller by 230 bytes: Before: text data bss dec hex filename 3797 240 0 4037 fc5 drivers/ata/libata-zpodd.o After: text data bss dec hex filename 3407 400 0 3807 edf drivers/ata/libata-zpodd.o Signed-off-by: Colin Ian King Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman

libata: blacklist Micron 500IT SSD with MU01 firmware

2018-05-30T05:48:51+00:00

commit 136d769e0b3475d71350aa3648a116a6ee7a8f6c upstream. While whitelisting Micron M500DC drives, the tweaked blacklist entry enabled queued TRIM from M500IT variants also. But these do not support queued TRIM. And while using those SSDs with the latest kernel we have seen errors and even the partition table getting corrupted. Some part from the dmesg: [ 6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133 [ 6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 6.741026] ata1.00: supports DRM functions and may not be fully accessible [ 6.759887] ata1.00: configured for UDMA/133 [ 6.762256] scsi 0:0:0:0: Direct-Access ATA Micron_M500IT_MT MU01 PQ: 0 ANSI: 5 and then for the error: [ 120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen [ 120.860338] ata1.00: irq_stat 0x40000008 [ 120.860342] ata1.00: failed command: SEND FPDMA QUEUED [ 120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout) [ 120.860353] ata1.00: status: { DRDY } [ 120.860543] ata1: hard resetting link [ 121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 121.166376] ata1.00: supports DRM functions and may not be fully accessible [ 121.186238] ata1.00: supports DRM functions and may not be fully accessible [ 121.204445] ata1.00: configured for UDMA/133 [ 121.204454] ata1.00: device reported invalid CHS sector 0 [ 121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08 [ 121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current] [ 121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4 [ 121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00 [ 121.204559] print_req_error: I/O error, dev sda, sector 272512 After few reboots with these errors, and the SSD is corrupted. After blacklisting it, the errors are not seen and the SSD does not get corrupted any more. Fixes: 243918be6393 ("libata: Do not blacklist Micron M500DC") Cc: Martin K. Petersen Cc: stable@vger.kernel.org Signed-off-by: Sudip Mukherjee Signed-off-by: Tejun Heo Signed-off-by: Greg Kroah-Hartman

libata: Blacklist some Sandisk SSDs for NCQ

2018-05-30T05:48:51+00:00

commit 322579dcc865b94b47345ad1b6002ad167f85405 upstream. Sandisk SSDs SD7SN6S256G and SD8SN8U256G are regularly locking up regularly under sustained moderate load with NCQ enabled. Blacklist for now. Signed-off-by: Tejun Heo Reported-by: Dave Jones Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman