kernel/linux.git/drivers/ata/Makefile, branch v6.1.168

ata: ahci: Add DWC AHCI SATA controller support

2022-09-16T16:40:15+00:00

Synopsys AHCI SATA controller can work pretty under with the generic AHCI-platform driver control. But there are vendor-specific peculiarities which can tune the device performance up and which may need to be fixed up for proper device functioning. In addition some DWC AHCI-based controllers may require small platform-specific fixups, so adding them in the generic AHCI driver would have ruined the code simplicity. Shortly speaking in order to keep the generic AHCI-platform code clean and have DWC AHCI SATA-specific features supported we suggest to add a dedicated DWC AHCI SATA device driver. Aside with the standard AHCI-platform resources getting, enabling/disabling and the controller registration the new driver performs the next actions. First of all there is a way to verify whether the HBA/ports capabilities activated in OF are correct. Almost all features availability is reflected in the vendor-specific parameters registers. So the DWC AHCI driver does the capabilities sanity check based on the corresponding fields state. Secondly if either the Command Completion Coalescing or the Device Sleep feature is enabled the DWC AHCI-specific internal 1ms timer must be fixed in accordance with the application clock signal frequency. In particular the timer value must be set to be Fapp * 1000. Normally the SoC designers pre-configure the TIMER1MS register to contain a correct value by default. But the platforms can support the application clock rate change. If that happens the 1ms timer value must be accordingly updated otherwise the dependent features won't work as expected. In the DWC AHCI driver we suggest to rely on the "aclk" reference clock rate to set the timer interval up. That clock source is supposed to be the AHCI SATA application clock in accordance with the DT bindings. Finally DWC AHCI SATA controller AXI/AHB bus DMA-engine can be tuned up to transfer up to 1024 * FIFO words at a time by setting the Tx/Rx transaction size in the DMA control register. The maximum value depends on the DMA data bus and AXI/AHB bus maximum burst length. In most of the cases it's better to set the maximum possible value to reach the best AHCI SATA controller performance. But sometimes in order to improve the system interconnect responsiveness, transferring in smaller data chunks may be more preferable. For such cases and for the case when the default value doesn't provide the best DMA bus performance we suggest to use the new HBA-port specific DT-properties "snps,{tx,rx}-ts-max" to tune the DMA transactions size up. After all the settings denoted above are handled the DWC AHCI SATA driver proceeds further with the standard AHCI-platform host initializations. Note since DWC AHCI controller is now have a dedicated driver we can discard the corresponding compatible string from the ahci-platform.c module. The same concerns "snps,spear-ahci" compatible string, which is also based on the DWC AHCI IP-core. Signed-off-by: Serge Semin Reviewed-by: Hannes Reinecke Signed-off-by: Damien Le Moal

ata: start separating SATA specific code from libata-core.c

2020-03-26T16:28:19+00:00

Start separating SATA specific code from libata-core.c: * move following functions to libata-sata.c: - ata_tf_to_fis() - ata_tf_from_fis() - sata_link_scr_lpm() - ata_slave_link_init() - sata_lpm_ignore_phy_events() * group above functions together in * include libata-sata.c in the build when CONFIG_SATA_HOST=y Code size savings on m68k arch using (modified) atari_defconfig: text data bss dec hex filename before: 37582 572 40 38194 9532 drivers/ata/libata-core.o after: 36762 572 40 37374 91fe drivers/ata/libata-core.o Reviewed-by: Christoph Hellwig Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jens Axboe

ata: separate PATA timings code from libata-core.c

2020-03-26T16:28:19+00:00

Separate PATA timings code from libata-core.c: * add PATA_TIMINGS config option and make corresponding PATA host drivers (and ATA ACPI code) select it * move following PATA timings code to libata-pata-timings.c: - ata_timing_quantize() - ata_timing_merge() - ata_timing_find_mode() - ata_timing_compute() * group above functions together in * include libata-pata-timings.c in the build when PATA_TIMINGS config option is enabled * cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it depends on code from libata-core.c and libata-pata-timings.c while its only user is ATA ACPI) Code size savings on m68k arch using (modified) atari_defconfig: text data bss dec hex filename before: 39688 573 40 40301 9d6d drivers/ata/libata-core.o after: 37820 572 40 38432 9620 drivers/ata/libata-core.o Reviewed-by: Christoph Hellwig Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jens Axboe

ata: add Buddha PATA controller driver

2019-02-08T13:32:01+00:00

Add Buddha PATA controller driver. It enables libata support for the Buddha, Catweasel and X-Surf expansion boards on the Zorro expansion bus. Module removal is currently unsupported (the old IDE's buddha driver also doesn't support it). Tested-by: John Paul Adrian Glaubitz Cc: Michael Schmitz Cc: Geert Uytterhoeven Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Jens Axboe

Merge branch 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

2018-04-04T00:42:25+00:00

Pull libata updates from Tejun Heo: "Nothing too interesting. The biggest change is refcnting fix for ata_host - the bug is recent and can only be triggered on controller hotplug, so very few are hitting it. There also are a number of trivial license / error message changes and some hardware specific changes" * 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits) ahci: imx: add the imx8qm ahci sata support libata: ensure host is free'd on error exit paths ata: ahci-platform: add reset control support ahci: imx: fix the build warning ata: add Amiga Gayle PATA controller driver ahci: imx: add the imx6qp ahci sata support ata: change Tegra124 to Tegra ata: ahci_tegra: Add AHCI support for Tegra210 ata: ahci_tegra: disable DIPM ata: ahci_tegra: disable devslp for Tegra124 ata: ahci_tegra: initialize regulators from soc struct ata: ahci_tegra: Update initialization sequence dt-bindings: Tegra210: add binding documentation libata: add refcounting to ata_host pata_bk3710: clarify license version and use SPDX header pata_falcon: clarify license version and use SPDX header pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command() pata_macio: Delete an error message for a failed memory allocation in two functions pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe() sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start() ...

ata: remove bf54x driver

2018-03-26T13:56:56+00:00

The blackfin architecture is getting removed, so this driver is obsolete as well. Acked-by: Tejun Heo Signed-off-by: Arnd Bergmann

ata: add Amiga Gayle PATA controller driver

2018-03-19T14:41:36+00:00

Add Amiga Gayle PATA controller driver. It enables libata support for the on-board IDE interfaces on some Amiga models (A600, A1200, A4000 and A4000T) and also for IDE interfaces on the Zorro expansion bus (M-Tech E-Matrix 530 expansion card). Thanks to John Paul Adrian Glaubitz and Michael Schmitz for help with testing the driver. Tested-by: John Paul Adrian Glaubitz Cc: Michael Schmitz Cc: Geert Uytterhoeven Cc: Philippe Ombredanne Cc: Andy Shevchenko Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Tejun Heo

ata: remove pata_at32

2018-01-18T21:17:25+00:00

Since AVR32 was removed, pata_at32 is unselectable/uncompilable. Remove this driver. Signed-off-by: Corentin Labbe Signed-off-by: Tejun Heo

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

2017-11-02T10:10:55+00:00

Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart Reviewed-by: Philippe Ombredanne Reviewed-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman

ata: mediatek: add support for MediaTek SATA controller

2017-08-28T17:54:42+00:00

This adds support the AHCI-compliant Serial ATA controller present on MediaTek SoCs. Signed-off-by: Ryder Lee Acked-by: Tejun Heo Signed-off-by: Tejun Heo