kernel/linux.git/arch, branch v5.10.22

Revert "arm64: dts: amlogic: add missing ethernet reset ID"

2021-03-09T10:11:15+00:00

commit 19f6fe976a61f9afc289b062b7ef67f99b72e7b9 upstream. It has been reported on IRC and in KernelCI boot tests, this change breaks internal PHY support on the Amlogic G12A/SM1 Based boards. We suspect the added signal to reset more than the Ethernet MAC but also the MDIO/(RG)MII mux used to redirect the MAC signals to the internal PHY. This reverts commit f3362f0c18174a1f334a419ab7d567a36bd1b3f3 while we find and acceptable solution to cleanly reset the Ethernet MAC. Reported-by: Corentin Labbe Acked-by: Jérôme Brunet Signed-off-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210126080951.2383740-1-narmstrong@baylibre.com Signed-off-by: Greg Kroah-Hartman

arm64: mm: Set ZONE_DMA size based on early IORT scan

2021-03-09T10:11:13+00:00

commit 2b8652936f0ca9ca2e6c984ae76c7bfcda1b3f22 upstream We recently introduced a 1 GB sized ZONE_DMA to cater for platforms incorporating masters that can address less than 32 bits of DMA, in particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has peripherals that can only address up to 1 GB (and its PCIe host bridge can only access the bottom 3 GB) Instructing the DMA layer about these limitations is straight-forward, even though we had to fix some issues regarding memory limits set in the IORT for named components, and regarding the handling of ACPI _DMA methods. However, the DMA layer also needs to be able to allocate memory that is guaranteed to meet those DMA constraints, for bounce buffering as well as allocating the backing for consistent mappings. This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately, it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and potentially in other places where allocations cannot cross zone boundaries. Therefore, we should avoid having two separate DMA zones when possible. So let's do an early scan of the IORT, and only create the ZONE_DMA if we encounter any devices that need it. This puts the burden on the firmware to describe such limitations in the IORT, which may be redundant (and less precise) if _DMA methods are also being provided. However, it should be noted that this situation is highly unusual for arm64 ACPI machines. Also, the DMA subsystem still gives precedence to the _DMA method if implemented, and so we will not lose the ability to perform streaming DMA outside the ZONE_DMA if the _DMA method permits it. [nsaenz: unified implementation with DT's counterpart] Signed-off-by: Ard Biesheuvel Signed-off-by: Nicolas Saenz Julienne Tested-by: Jeremy Linton Acked-by: Lorenzo Pieralisi Acked-by: Hanjun Guo Cc: Jeremy Linton Cc: Lorenzo Pieralisi Cc: Nicolas Saenz Julienne Cc: Rob Herring Cc: Christoph Hellwig Cc: Robin Murphy Cc: Hanjun Guo Cc: Sudeep Holla Cc: Anshuman Khandual Link: https://lore.kernel.org/r/20201119175400.9995-7-nsaenzjulienne@suse.de Signed-off-by: Catalin Marinas Cc: Signed-off-by: Jing Xiangfeng Signed-off-by: Greg Kroah-Hartman

arm64: mm: Set ZONE_DMA size based on devicetree's dma-ranges

2021-03-09T10:11:13+00:00

commit 8424ecdde7df99d5426e1a1fd9f0fb36f4183032 upstream We recently introduced a 1 GB sized ZONE_DMA to cater for platforms incorporating masters that can address less than 32 bits of DMA, in particular the Raspberry Pi 4, which has 4 or 8 GB of DRAM, but has peripherals that can only address up to 1 GB (and its PCIe host bridge can only access the bottom 3 GB) The DMA layer also needs to be able to allocate memory that is guaranteed to meet those DMA constraints, for bounce buffering as well as allocating the backing for consistent mappings. This is why the 1 GB ZONE_DMA was introduced recently. Unfortunately, it turns out the having a 1 GB ZONE_DMA as well as a ZONE_DMA32 causes problems with kdump, and potentially in other places where allocations cannot cross zone boundaries. Therefore, we should avoid having two separate DMA zones when possible. So, with the help of of_dma_get_max_cpu_address() get the topmost physical address accessible to all DMA masters in system and use that information to fine-tune ZONE_DMA's size. In the absence of addressing limited masters ZONE_DMA will span the whole 32-bit address space, otherwise, in the case of the Raspberry Pi 4 it'll only span the 30-bit address space, and have ZONE_DMA32 cover the rest of the 32-bit address space. Signed-off-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/20201119175400.9995-6-nsaenzjulienne@suse.de Signed-off-by: Catalin Marinas Cc: Signed-off-by: Jing Xiangfeng Signed-off-by: Greg Kroah-Hartman

arm64: mm: Move zone_dma_bits initialization into zone_sizes_init()

2021-03-09T10:11:13+00:00

commit 9804f8c69b04a39d0ba41d19e6bdc6aa91c19725 upstream zone_dma_bits's initialization happens earlier that it's actually needed, in arm64_memblock_init(). So move it into the more suitable zone_sizes_init(). Signed-off-by: Nicolas Saenz Julienne Tested-by: Jeremy Linton Link: https://lore.kernel.org/r/20201119175400.9995-3-nsaenzjulienne@suse.de Signed-off-by: Catalin Marinas Cc: Signed-off-by: Jing Xiangfeng Signed-off-by: Greg Kroah-Hartman

arm64: mm: Move reserve_crashkernel() into mem_init()

2021-03-09T10:11:13+00:00

commit 0a30c53573b07d5561457e41fb0ab046cd857da5 upstream crashkernel might reserve memory located in ZONE_DMA. We plan to delay ZONE_DMA's initialization after unflattening the devicetree and ACPI's boot table initialization, so move it later in the boot process. Specifically into bootmem_init() since request_standard_resources() depends on it. Signed-off-by: Nicolas Saenz Julienne Tested-by: Jeremy Linton Link: https://lore.kernel.org/r/20201119175400.9995-2-nsaenzjulienne@suse.de Signed-off-by: Catalin Marinas Cc: Signed-off-by: Jing Xiangfeng Signed-off-by: Greg Kroah-Hartman

powerpc/sstep: Fix incorrect return from analyze_instr()

2021-03-07T11:34:16+00:00

commit 718aae916fa6619c57c348beaedd675835cf1aa1 upstream. We currently just percolate the return value from analyze_instr() to the caller of emulate_step(), especially if it is a -1. For one particular case (opcode = 4) for instructions that aren't currently emulated, we are returning 'should not be single-stepped' while we should have returned 0 which says 'did not emulate, may have to single-step'. Fixes: 930d6288a26787 ("powerpc: sstep: Add support for maddhd, maddhdu, maddld instructions") Signed-off-by: Ananth N Mavinakayanahalli Suggested-by: Michael Ellerman Tested-by: Naveen N. Rao Reviewed-by: Sandipan Das Signed-off-by: Michael Ellerman Link: https://lore.kernel.org/r/161157999039.64773.14950289716779364766.stgit@thinktux.local Signed-off-by: Naveen N. Rao Signed-off-by: Greg Kroah-Hartman

powerpc/sstep: Check instruction validity against ISA version before emulation

2021-03-07T11:34:15+00:00

commit 8813ff49607eab3caaf40fe8929b0ce7dc68e85f upstream. We currently unconditionally try to emulate newer instructions on older Power versions that could cause issues. Gate it. Fixes: 350779a29f11 ("powerpc: Handle most loads and stores in instruction emulation code") Signed-off-by: Ananth N Mavinakayanahalli Signed-off-by: Michael Ellerman Link: https://lore.kernel.org/r/161157995977.64773.13794501093457185080.stgit@thinktux.local [Dropped a few missing hunks for the backport to v5.10] Signed-off-by: Naveen N. Rao Signed-off-by: Greg Kroah-Hartman

xen: fix p2m size in dom0 for disabled memory hotplug case

2021-03-07T11:34:15+00:00

commit 882213990d32fd224340a4533f6318dd152be4b2 upstream. Since commit 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory") foreign mappings are using guest physical addresses allocated via ZONE_DEVICE functionality. This will result in problems for the case of no balloon memory hotplug being configured, as the p2m list will only cover the initial memory size of the domain. Any ZONE_DEVICE allocated address will be outside the p2m range and thus a mapping can't be established with that memory address. Fix that by extending the p2m size for that case. At the same time add a check for a to be created mapping to be within the p2m limits in order to detect errors early. While changing a comment, remove some 32-bit leftovers. This is XSA-369. Fixes: 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory") Cc: # 5.9 Reported-by: Marek Marczykowski-Górecki Signed-off-by: Juergen Gross Reviewed-by: Jan Beulich Signed-off-by: Juergen Gross Signed-off-by: Greg Kroah-Hartman

Xen/gnttab: handle p2m update errors on a per-slot basis

2021-03-07T11:34:15+00:00

commit 8310b77b48c5558c140e7a57a702e7819e62f04e upstream. Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating error leaves the full batch in an ambiguous state as far as the caller is concerned. Instead flags respective slots as bad, unmapping what was mapped there right away. HYPERVISOR_grant_table_op()'s return value and the individual unmap slots' status fields get used only for a one-time - there's not much we can do in case of a failure. Note that there's no GNTST_enomem or alike, so GNTST_general_error gets used. The map ops' handle fields get overwritten just to be on the safe side. This is part of XSA-367. Cc: Signed-off-by: Jan Beulich Reviewed-by: Juergen Gross Link: https://lore.kernel.org/r/96cccf5d-e756-5f53-b91a-ea269bfb9be0@suse.com Signed-off-by: Juergen Gross Signed-off-by: Greg Kroah-Hartman

parisc: Bump 64-bit IRQ stack size to 64 KB

2021-03-07T11:34:13+00:00

[ Upstream commit 31680c1d1595a59e17c14ec036b192a95f8e5f4a ] Bump 64-bit IRQ stack size to 64 KB. I had a kernel IRQ stack overflow on the mx3210 debian buildd machine. This patch increases the 64-bit IRQ stack size to 64 KB. The 64-bit stack size needs to be larger than the 32-bit stack size since registers are twice as big. Signed-off-by: John David Anglin Signed-off-by: Helge Deller Signed-off-by: Sasha Levin