kernel/linux.git/arch/sh/mm/cache.c, branch linux-4.16.y

sh: do not perform IPI-based cache flush except on boards that need it

2016-08-05T03:29:40+00:00

Signed-off-by: Rich Felker

sh: add support for J-Core J2 processor

2016-08-05T03:29:31+00:00

At the CPU/ISA level, the J2 is compatible with SH-2, and thus the changes to add J2 support build on existing SH-2 support. However, J2 does not duplicate the memory-mapped SH-2 features like the cache interface. Instead, the cache interfaces is described in the device tree, and new code is added to be able to access the flat device tree at early boot before it is unflattened. Support is also added for receiving interrupts on trap numbers in the range 16 to 31, since the J-Core aic1 interrupt controller generates these traps. This range was unused but nominally for hardware exceptions on SH-2, and a few values in this range were used for exceptions on SH-2A, but SH-2A has its own version of the relevant code. No individual cpu subtypes are added for J2 since the intent moving forward is to represent SoCs with device tree rather than as hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item exists only to fit into the existing cpu selection mechanism until it is overhauled. Signed-off-by: Rich Felker

sh: disable aliased page logic on NOMMU models

2016-07-31T03:33:32+00:00

SH3/4 (with MMU) have a virtually indexed cache, requiring explicit work to avoid consistency problems arising from having the same physical address range cached in multiple cache lines. This is unneeded for the NOMMU case, and some of the resulting code paths (kmap_coherent) don't work. SH2 only avoided this problem by having a 4-way associative cache with way size equal to the page size (4k), yielding no cache index bits outside of the page offset and thus no aliases. Signed-off-by: Rich Felker

mm: differentiate page_mapped() from page_mapcount() for compound pages

2016-01-16T01:56:32+00:00

Let's define page_mapped() to be true for compound pages if any sub-pages of the compound page is mapped (with PMD or PTE). On other hand page_mapcount() return mapcount for this particular small page. This will make cases like page_get_anon_vma() behave correctly once we allow huge pages to be mapped with PTE. Most users outside core-mm should use page_mapcount() instead of page_mapped(). Signed-off-by: Kirill A. Shutemov Tested-by: Sasha Levin Tested-by: Aneesh Kumar K.V Acked-by: Jerome Marchand Cc: Vlastimil Babka Cc: Andrea Arcangeli Cc: Hugh Dickins Cc: Dave Hansen Cc: Mel Gorman Cc: Rik van Riel Cc: Naoya Horiguchi Cc: Steve Capper Cc: Johannes Weiner Cc: Michal Hocko Cc: Christoph Lameter Cc: David Rientjes Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

flush_icache_range: export symbol to fix build errors

2014-08-29T23:28:17+00:00

Fix building errors occuring due to a missing export of flush_icache_range() in kisskb.ellerman.id.au/kisskb/buildresult/11677809/ ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined! Signed-off-by: Pranith Kumar Reported-by: Geert Uytterhoeven Acked-by: Vineet Gupta [arc] Acked-by: Richard Kuo [hexagon] Cc: Chris Metcalf Cc: Chris Zankel Acked-by: Max Filippov [xtensa] Cc: Noam Camus Cc: Masami Hiramatsu Acked-by: Zhigang Lu [tile] Cc: Kirill Tkhai Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

sh: prefix sh-specific "CCR" and "CCR2" by "SH_"

2014-03-04T15:55:49+00:00

Commit bcf24e1daa94 ("mmc: omap_hsmmc: use the generic config for omap2plus devices"), enabled the build for other platforms for compile testing. sh-allmodconfig now fails with: include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1 This happens because SuperH #defines "CCR", which is one of the enum values in include/linux/omap-dma.h. There's a similar issue with "CCR2" on sh2a. As "CCR" and "CCR2" are too generic names for global #defines, prefix them with "SH_" to fix this. Signed-off-by: Geert Uytterhoeven Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds

sh: remove the second argument of k[un]map_atomic()

2012-03-20T13:48:15+00:00

Signed-off-by: Cong Wang

sh: Flush executable pages in copy_user_highpage

2011-02-15T07:24:31+00:00

This resolves a problem seen when using the Android dynamic linker. Sometimes the dynamic linker would seg-fault at start up and this was eventually traced to the handling of a COW fault for a page which was being modified by the linker. If there was no cache aliasing between the kernel and the user page, the page was not flushed, leaving the newly copied data in the D-cache. However when executing instructions from that page, the I-cache is filled directly from external memory, rather than the D-cache, and causing garbage to be executed. Signed-off-by: Stuart Menefy Signed-off-by: Paul Mundt

sh: Assume new page cache pages have dirty dcache lines.

2010-12-01T06:39:51+00:00

This follows the ARM change c01778001a4f5ad9c62d882776235f3f31922fdd ("ARM: 6379/1: Assume new page cache pages have dirty D-cache") for the same rationale: There are places in Linux where writes to newly allocated page cache pages happen without a subsequent call to flush_dcache_page() (several PIO drivers including USB HCD). This patch changes the meaning of PG_arch_1 to be PG_dcache_clean and always flush the D-cache for a newly mapped page in update_mmu_cache(). This addresses issues seen with executing binaries from MMC, in addition to some of the other HCDs that don't explicitly do cache management for their pipe-in buffers. Requested-by: Yoshihiro Shimoda Signed-off-by: Paul Mundt

sh: Enable SH-X3 hardware synonym avoidance handling.

2010-04-19T08:27:17+00:00

This enables support for the hardware synonym avoidance handling on SH-X3 CPUs for the case where dcache aliases are possible. icache handling is retained, but we flip on broadcasting of the block invalidations due to the lack of coherency otherwise on SMP. Signed-off-by: Paul Mundt