kernel/linux.git/arch/m68k/mac, branch linux-5.9.y

treewide: Use fallthrough pseudo-keyword

2020-08-23T22:36:59+00:00

Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva

m68k: mac: Improve IOP debug messages

2020-07-13T09:39:13+00:00

Always dump the full message and reply. Avoid printing partial lines as this output gets mixed up with the output from called functions. Don't output the state of idle channels. Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/317909d69244f06581973c5839382f5516cd9a1c.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Don't send uninitialized data in IOP message reply

2020-07-13T09:39:13+00:00

Clear the message reply before calling iop_complete(). This code path is not normally executed but should that happen let's arrange for consistent behaviour from the IOP. Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/8e35df4d193b082cb6285b1f30c949ff7e30e99e.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Fix IOP status/control register writes

2020-07-13T09:39:13+00:00

When writing values to the IOP status/control register make sure those values do not have any extraneous bits that will clear interrupt flags. To place the SCC IOP into bypass mode would be desirable but this is not achieved by writing IOP_DMAINACTIVE | IOP_RUN | IOP_AUTOINC | IOP_BYPASS to the control register. Drop this ineffective register write. Remove the flawed and unused iop_bypass() function. Make use of the unused iop_stop() function. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/09bcb7359a1719a18b551ee515da3c4c3cf709e6.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Don't send IOP message until channel is idle

2020-07-13T09:39:13+00:00

In the following sequence of calls, iop_do_send() gets called when the "send" channel is not in the IOP_MSG_IDLE state: iop_ism_irq() iop_handle_send() (msg->handler)() iop_send_message() iop_do_send() Avoid this by testing the channel state before calling iop_do_send(). When sending, and iop_send_queue is empty, call iop_do_send() because the channel is idle. If iop_send_queue is not empty, iop_do_send() will get called later by iop_handle_send(). Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/6d667c39e53865661fa5a48f16829d18ed8abe54.1590880333.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

mm: don't include asm/pgtable.h if linux/mm.h is already included

2020-06-09T16:39:13+00:00

Patch series "mm: consolidate definitions of page table accessors", v2. The low level page table accessors (pXY_index(), pXY_offset()) are duplicated across all architectures and sometimes more than once. For instance, we have 31 definition of pgd_offset() for 25 supported architectures. Most of these definitions are actually identical and typically it boils down to, e.g. static inline unsigned long pmd_index(unsigned long address) { return (address >> PMD_SHIFT) & (PTRS_PER_PMD - 1); } static inline pmd_t *pmd_offset(pud_t *pud, unsigned long address) { return (pmd_t *)pud_page_vaddr(*pud) + pmd_index(address); } These definitions can be shared among 90% of the arches provided XYZ_SHIFT, PTRS_PER_XYZ and xyz_page_vaddr() are defined. For architectures that really need a custom version there is always possibility to override the generic version with the usual ifdefs magic. These patches introduce include/linux/pgtable.h that replaces include/asm-generic/pgtable.h and add the definitions of the page table accessors to the new header. This patch (of 12): The linux/mm.h header includes to allow inlining of the functions involving page table manipulations, e.g. pte_alloc() and pmd_alloc(). So, there is no point to explicitly include in the files that include . The include statements in such cases are remove with a simple loop: for f in $(git grep -l "include ") ; do sed -i -e '/include / d' $f done Signed-off-by: Mike Rapoport Signed-off-by: Andrew Morton Cc: Arnd Bergmann Cc: Borislav Petkov Cc: Brian Cain Cc: Catalin Marinas Cc: Chris Zankel Cc: "David S. Miller" Cc: Geert Uytterhoeven Cc: Greentime Hu Cc: Greg Ungerer Cc: Guan Xuetao Cc: Guo Ren Cc: Heiko Carstens Cc: Helge Deller Cc: Ingo Molnar Cc: Ley Foon Tan Cc: Mark Salter Cc: Matthew Wilcox Cc: Matt Turner Cc: Max Filippov Cc: Michael Ellerman Cc: Michal Simek Cc: Mike Rapoport Cc: Nick Hu Cc: Paul Walmsley Cc: Richard Weinberger Cc: Rich Felker Cc: Russell King Cc: Stafford Horne Cc: Thomas Bogendoerfer Cc: Thomas Gleixner Cc: Tony Luck Cc: Vincent Chen Cc: Vineet Gupta Cc: Will Deacon Cc: Yoshinori Sato Link: http://lkml.kernel.org/r/20200514170327.31389-1-rppt@kernel.org Link: http://lkml.kernel.org/r/20200514170327.31389-2-rppt@kernel.org Signed-off-by: Linus Torvalds

m68k: mac: Avoid stuck ISM IOP interrupt on Quadra 900/950

2020-05-25T08:55:56+00:00

On a Quadra 900/950, the ISM IOP IRQ output pin is connected to an edge-triggered input on VIA2. It is theoretically possible that this signal could fail to produce the expected VIA2 interrupt. The two IOP interrupt flags can be asserted in any order but the logic in iop_ism_irq() does not allow for that. In particular, INT0 can be asserted right after INT0 is checked and before INT1 is cleared. Such an interrupt would produce no new edge and VIA2 would detect no further interrupts from the IOP. Avoid this by looping over the INT0/1 handlers so an edge can be produced. Signed-off-by: Finn Thain Tested-by: Stan Johnson Cc: Joshua Thompson Link: https://lore.kernel.org/r/bfbb71db52c5e162d3afa25a28fc5d535ca87138.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Remove misleading comment

2020-05-25T08:55:56+00:00

This code path was tested on a Quadra 950 a long time ago and the comment isn't needed. Signed-off-by: Finn Thain Cc: Joshua Thompson Link: https://lore.kernel.org/r/10dff3e7c17d363a4b239aae7b3ebab32bef3547.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Don't call via_flush_cache() on Mac IIfx

2020-05-25T08:55:56+00:00

There is no VIA2 chip on the Mac IIfx, so don't call via_flush_cache(). This avoids a boot crash which appeared in v5.4. printk: console [ttyS0] enabled printk: bootconsole [debug0] disabled printk: bootconsole [debug0] disabled Calibrating delay loop... 9.61 BogoMIPS (lpj=48064) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) devtmpfs: initialized random: get_random_u32 called from bucket_table_alloc.isra.27+0x68/0x194 with crng_init=0 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes, linear) NET: Registered protocol family 16 Data read fault at 0x00000000 in Super Data (pc=0x8a6a) BAD KERNEL BUSERR Oops: 00000000 Modules linked in: PC: [<00008a6a>] via_flush_cache+0x12/0x2c SR: 2700 SP: 01c1fe3c a2: 01c24000 d0: 00001119 d1: 0000000c d2: 00012000 d3: 0000000f d4: 01c06840 d5: 00033b92 a0: 00000000 a1: 00000000 Process swapper (pid: 1, task=01c24000) Frame format=B ssw=0755 isc=0200 isb=fff7 daddr=00000000 dobuf=01c1fed0 baddr=00008a6e dibuf=0000004e ver=f Stack from 01c1fec4: 01c1fed0 00007d7e 00010080 01c1fedc 0000792e 00000001 01c1fef4 00006b40 01c80000 00040000 00000006 00000003 01c1ff1c 004a545e 004ff200 00040000 00000000 00000003 01c06840 00033b92 004a5410 004b6c88 01c1ff84 000021e2 00000073 00000003 01c06840 00033b92 0038507a 004bb094 004b6ca8 004b6c88 004b6ca4 004b6c88 000021ae 00020002 00000000 01c0685d 00000000 01c1ffb4 0049f938 00409c85 01c06840 0045bd40 00000073 00000002 00000002 00000000 Call Trace: [<00007d7e>] mac_cache_card_flush+0x12/0x1c [<00010080>] fix_dnrm+0x2/0x18 [<0000792e>] cache_push+0x46/0x5a [<00006b40>] arch_dma_prep_coherent+0x60/0x6e [<00040000>] switched_to_dl+0x76/0xd0 [<004a545e>] dma_atomic_pool_init+0x4e/0x188 [<00040000>] switched_to_dl+0x76/0xd0 [<00033b92>] parse_args+0x0/0x370 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<000021e2>] do_one_initcall+0x34/0x1be [<00033b92>] parse_args+0x0/0x370 [<0038507a>] strcpy+0x0/0x1e [<000021ae>] do_one_initcall+0x0/0x1be [<00020002>] do_proc_dointvec_conv+0x54/0x74 [<0049f938>] kernel_init_freeable+0x126/0x190 [<0049f94c>] kernel_init_freeable+0x13a/0x190 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<00041798>] complete+0x0/0x3c [<000b9b0c>] kfree+0x0/0x20a [<0038df98>] schedule+0x0/0xd0 [<0038d604>] kernel_init+0x0/0xda [<0038d610>] kernel_init+0xc/0xda [<0038d604>] kernel_init+0x0/0xda [<00002d38>] ret_from_kernel_thread+0xc/0x14 Code: 0000 2079 0048 10da 2279 0048 10c8 d3c8 <1011> 0200 fff7 1280 d1f9 0048 10c8 1010 0000 0008 1080 4e5e 4e75 4e56 0000 2039 Disabling lock debugging due to kernel taint Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b Thanks to Stan Johnson for capturing the console log and running git bisect. Git bisect said commit 8e3a68fb55e0 ("dma-mapping: make dma_atomic_pool_init self-contained") is the first "bad" commit. I don't know why. Perhaps mach_l2_flush first became reachable with that commit. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: Stan Johnson Signed-off-by: Finn Thain Cc: Joshua Thompson Link: https://lore.kernel.org/r/b8bbeef197d6b3898e82ed0d231ad08f575a4b34.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven

m68k: mac: Revisit floppy disc controller base addresses

2019-08-19T11:24:10+00:00

Rename floppy_type macros to make them more consistent with the scsi_type macros, which are named after classes of models with similar memory maps. The MAC_FLOPPY_OLD symbol is introduced to change the relevant base address from 0x50F00000 to 0x50000000 (consistent with MAC_SCSI_OLD). The documentation for LC-class machines has the IO devices at offsets from $50F00000. Use these addresses for MAC_FLOPPY_LC (consistent with MAC_SCSI_LC) because they may not be aliased elsewhere in the memory map. Add comments with controller type information from 'Designing Cards and Drivers for the Macintosh Family', relevant Developer Notes and http://mess.redump.net/mess/driver_info/mac_technical_notes Adopt phys_addr_t to avoid type casts. Signed-off-by: Finn Thain Tested-by: Stan Johnson Acked-by: Laurent Vivier Signed-off-by: Geert Uytterhoeven