kernel/linux.git/arch/arm/boot/dts/sun7i-a20-pcduino3.dts, branch linux-4.7.y

ARM: dts: sun7i: Enable audio codec on pcDuino

2015-11-17T08:40:07+00:00

Enable the on-chip audio codec Signed-off-by: Jelle van der Waa Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard

ARM: dts: sun7i: Enable USB DRC on pcDuino 3

2015-09-27T08:21:16+00:00

Enable the otg/drc usb controller on the pcDuino 3. Note this board has the otg-vbus connected directly to the 5v-dcc of the board, so there is no vbus0 regulator, nor vbus0-det. Signed-off-by: Jelle van der Waa Signed-off-by: Hans de Goede Signed-off-by: Maxime Ripard

ARM: dts: sun7i: Add regulator configuration to the pcduino3 dts file

2015-09-27T08:21:15+00:00

Add regulator configuration to the pcduino3 dts file. Signed-off-by: Jelle van der Waa Signed-off-by: Hans de Goede [Maxime: Removed usb_power_supply node that isn't defined in the DTSI] Signed-off-by: Maxime Ripard

ARM: sunxi: dt: Remove the FSF address

2015-05-10T08:22:23+00:00

The FSF address triggers a warning on checkpatch, saying that the FSF license is already present in the Linux source code, and that it has already changed in the past. Remove it from our DT, as suggested. Signed-off-by: Maxime Ripard

ARM: sunxi: dts: split IR pins for A10 and A20

2015-05-02T11:52:55+00:00

Currently none of the target boards nor the driver supports IR TX. However this pin is used in a few instances as a GPIO. Split the pin ctrl descriptions so that only the IR RX is configured to be used. Signed-off-by: Marcus Cooper Signed-off-by: Maxime Ripard

ARM: sunxi: DT: Add stdout-path property

2015-04-27T06:20:30+00:00

Add UART aliases and stdout-path property for all the Allwinner boards so that we won't have to rely on the bootargs' console= value, while working with legacy bootloaders. While we're at it, also remove the mentions of earlyprintk in the bootargs, that will remove our default bootargs entirely, and allow the kernel to boot on a system even if DEBUG_LL is configured for another system. Signed-off-by: Maxime Ripard

ARM: sun7i: pcduino3: Convert to DT label based syntax

2015-04-27T06:20:24+00:00

In order to lessen the amount of duplication of the DT tree, ease the new and follow the trend that prefers to use label based references when overriding DTSI nodes, convert the board to this syntax Signed-off-by: Maxime Ripard

ARM: sunxi: DT: Convert the DTs to use the generic interrupt header

2015-01-21T08:58:57+00:00

The NMI IRQ controller uses the standard flags definition for the IRQ level and edges. Use the common header to use defines instead of opaque numbers. Signed-off-by: Maxime Ripard

ARM: sunxi: DT: Convert the DTs to use a header for the pinctrl nodes

2015-01-21T08:58:57+00:00

The pinctrl nodes require some extra opaque arguments for the pull up and drive strength values. Introduce a new header file and convert the device trees to replace these opaque numbers by defines. Signed-off-by: Maxime Ripard

ARM: sunxi: DT: convert DTs to use common GPIOs includes

2015-01-21T08:58:56+00:00

Replace the various raw GPIO flags by their definition in the common dt-bindings header. Signed-off-by: Maxime Ripard