kernel/linux.git/Documentation/hwmon, branch v5.10.257

hwmon: (adm1177) fix sysfs ABI violation and current unit conversion

2026-04-18T08:31:06+00:00

[ Upstream commit bf08749a6abb6d1959bfdc0edc32c640df407558 ] The adm1177 driver exposes the current alert threshold through hwmon_curr_max_alarm. This violates the hwmon sysfs ABI, where *_alarm attributes are read-only status flags and writable thresholds must use currN_max. The driver also stores the threshold internally in microamps, while currN_max is defined in milliamps. Convert the threshold accordingly on both the read and write paths. Widen the cached threshold and related calculations to 64 bits so that small shunt resistor values do not cause truncation or overflow. Also use 64-bit arithmetic for the mA/uA conversions, clamp writes to the range the hardware can represent, and propagate failures from adm1177_write_alert_thr() instead of silently ignoring them. Update the hwmon documentation to reflect the attribute rename and the correct units returned by the driver. Fixes: 09b08ac9e8d5 ("hwmon: (adm1177) Add ADM1177 Hot Swap Controller and Digital Power Monitor driver") Signed-off-by: Sanman Pradhan Acked-by: Nuno Sá Link: https://lore.kernel.org/r/20260325051246.28262-1-sanman.pradhan@hpe.com Signed-off-by: Guenter Roeck Signed-off-by: Sasha Levin

hwmon: (lm90) Add basic support for TI TMP461

2021-12-29T11:25:59+00:00

[ Upstream commit f8344f7693a25d9025a59d164450b50c6f5aa3c0 ] TMP461 is almost identical to TMP451 and was actually detected as TMP451 with the existing lm90 driver if its I2C address is 0x4c. Add support for it to the lm90 driver. At the same time, improve the chip detection function to at least try to distinguish between TMP451 and TMP461. As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations"). TMP461 does not support word operations on temperature registers, which causes bad temperature readings with the tmp401 driver. The lm90 driver does not perform word operations on temperature registers and thus does not have this problem. Support is listed as basic because TMP461 supports a sensor resolution of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125 degrees C. Also, the TMP461 supports negative temperatures with its default temperature range, which is not the case for similar chips supported by the lm90 and the tmp401 drivers. Those limitations will be addressed with follow-up patches. Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations") Reported-by: David T. Wilson Cc: David T. Wilson Signed-off-by: Guenter Roeck Signed-off-by: Sasha Levin

hwmon: (max31790) Fix pwmX_enable attributes

2021-07-14T14:55:55+00:00

[ Upstream commit 148c847c9e5a54b99850617bf9c143af9a344f92 ] pwmX_enable supports three possible values: 0: Fan control disabled. Duty cycle is fixed to 0% 1: Fan control enabled, pwm mode. Duty cycle is determined by values written into Target Duty Cycle registers. 2: Fan control enabled, rpm mode Duty cycle is adjusted such that fan speed matches the values in Target Count registers The current code does not do this; instead, it mixes pwm control configuration with fan speed monitoring configuration. Worse, it reports that pwm control would be disabled (pwmX_enable==0) when it is in fact enabled in pwm mode. Part of the problem may be that the chip sets the "TACH input enable" bit on its own whenever the mode bit is set to RPM mode, but that doesn't mean that "TACH input enable" accurately reflects the pwm mode. Fix it up and only handle pwm control with the pwmX_enable attributes. In the documentation, clarify that disabling pwm control (pwmX_enable=0) sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN is set together with RPM_MODE. While at it, only update the configuration register if the configuration has changed, and only update the cached configuration if updating the chip configuration was successful. Cc: Jan Kundrát Cc: Václav Kubernát Signed-off-by: Guenter Roeck Tested-by: Václav Kubernát Reviewed-by: Jan Kundrát Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net Signed-off-by: Sasha Levin

hwmon: (max31790) Report correct current pwm duty cycles

2021-07-14T14:55:55+00:00

[ Upstream commit 897f6339893b741a5d68ae8e2475df65946041c2 ] The MAX31790 has two sets of registers for pwm duty cycles, one to request a duty cycle and one to read the actual current duty cycle. Both do not have to be the same. When reporting the pwm duty cycle to the user, the actual pwm duty cycle from pwm duty cycle registers needs to be reported. When setting it, the pwm target duty cycle needs to be written. Since we don't know the actual pwm duty cycle after a target pwm duty cycle has been written, set the valid flag to false to indicate that actual pwm duty cycle should be read from the chip instead of using cached values. Cc: Jan Kundrát Cc: Václav Kubernát Signed-off-by: Guenter Roeck Tested-by: Václav Kubernát Reviewed-by: Jan Kundrát Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net Signed-off-by: Sasha Levin

docs: hwmon: mp2975.rst: address some html build warnings

2020-10-28T17:26:10+00:00

.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation. .../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent. .../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation. .../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent. .../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent. .../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree List blocks should have blank lines before and after them, in order to be properly parsed. Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller") Signed-off-by: Mauro Carvalho Chehab Acked-by: Guenter Roeck Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org Signed-off-by: Jonathan Corbet

docs: hwmon: adm1266.rst: fix a broken reference

2020-10-28T17:26:10+00:00

The reference was missing the extension, causing the check script to complain. Signed-off-by: Mauro Carvalho Chehab Acked-by: Guenter Roeck Link: https://lore.kernel.org/r/3d64372dabcdcea144cdc9972c245812ea2a84cb.1603791716.git.mchehab+huawei@kernel.org Signed-off-by: Jonathan Corbet

Merge tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

2020-10-14T22:56:58+00:00

Pull MFD updates from Lee Jones: "New Drivers: - Add support for initialising shared (between children) Regmaps - Add support for Kontron SL28CPLD - Add support for ENE KB3930 Embedded Controller - Add support for Intel FPGA PAC MAX 10 BMC New Device Support: - Add support for Power to Ricoh RN5T618 - Add support for UART to Intel Lakefield - Add support for LP87524_Q1 to Texas Instruments LP87565 New Functionality: - Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1 - Use new helper dev_err_probe(); madera-core, stmfx, wcd934x - Use new GPIOD API; dm355evm_msp - Add wake-up capability; sprd-sc27xx-spi - Add ACPI support; kempld-core Fix-ups: - Trivial (spelling/whitespace); Kconfig, ab8500 - Fix for unused variables; khadas-mcu, kempld-core - Remove unused header file(s); mt6360-core - Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic - Add COMPILE_TEST support; asic3, tmio_core - Add dependency on I2C; SL28CPLD Bug Fixes: - Fix memory leak(s); sm501 - Do not free regmap_config's 'name' until exit; syscon" * tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits) mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI mfd: sl28cpld: Depend on I2C mfd: asic3: Build if COMPILE_TEST=y dt-bindings: mfd: Correct interrupt flags in examples mfd: Add ACPI support to Kontron PLD driver mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC mfd: lp87565: Add LP87524-Q1 variant dt-bindings: mfd: Add LP87524-Q1 dt-bindings: mfd: lp87565: Convert to yaml mfd: mt6360: Remove unused include mfd: sm501: Fix leaks in probe() mfd: syscon: Don't free allocated name for regmap_config dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings dt-bindings: mfd: ab8500: Remove weird Unicode characters mfd: sprd: Add wakeup capability for PMIC IRQ mfd: intel-lpss: Add device IDs for UART ports for Lakefield mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table mfd: wcd934x: Simplify with dev_err_probe() mfd: stmfx: Simplify with dev_err_probe() ...

Merge tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

2020-10-13T17:15:31+00:00

Pull hwmon updates from Guenter Roeck: "New driver and chip support: - Moortec MR75203 PVT controller - MPS Multi-phase mp2975 controller - ADM1266 - Zen3 CPUs - Intel MAX 10 BMC Enhancements: - Support for rated attributes in hwmon core - MAX20730: - Device monitoring via debugfs - VOUT readin adjustment vie devicetree bindings - LM75: - Devicetree support - Regulator support - Improved accumulationm logic in amd_energy driver - Added fan sensor to gsc-hwmon driver - Support for simplified I2C probing Various other minor fixes and improvements" * tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (64 commits) hwmon: (pmbus/max20730) adjust the vout reading given voltage divider dt-bindings: hwmon: max20730: adding device tree doc for max20730 hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller hwmon: Add DT bindings schema for PVT controller dt-bindings: hwmon: Add the +vs supply to the lm75 bindings dt-bindings: hwmon: Convert lm75 bindings to yaml docs: hwmon: (ltc2945) update datasheet link hwmon: (mlxreg-fan) Fix double "Mellanox" hwmon: (pmbus/max20730) add device monitoring via debugfs hwmon: (pmbus/max34440) Fix OC fault limits hwmon: (bt1-pvt) Wait for the completion with timeout hwmon: (bt1-pvt) Cache current update timeout hwmon: (bt1-pvt) Test sensor power supply on probe hwmon: (lm75) Add regulator support hwmon: Add hwmon driver for Intel MAX 10 BMC dt-bindings: Add MP2975 voltage regulator device hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller hwmon: (tmp513) fix spelling typo in comments hwmon: (amd_energy) Update driver documentation hwmon: (amd_energy) Improve the accumulation logic ...

docs: hwmon: (ltc2945) update datasheet link

2020-10-05T16:16:33+00:00

Old one isn't working anymore. Update to the latest datasheet link. Signed-off-by: Alexandru Ardelean Link: https://lore.kernel.org/r/20201005131226.1774081-1-alexandru.ardelean@analog.com Signed-off-by: Guenter Roeck

hwmon: Add hwmon driver for Intel MAX 10 BMC

2020-10-04T15:40:10+00:00

This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC chip connects to a set of sensor chips to monitor current, voltage, thermal and power of different components on board. The BMC firmware is responsible for sensor data sampling and recording in shared registers. Host driver reads the sensor data from these shared registers and exposes them to users as hwmon interfaces. Signed-off-by: Xu Yilun Signed-off-by: Wu Hao Signed-off-by: Matthew Gerlach Signed-off-by: Tom Rix Reviewed-by: Guenter Roeck Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com [groeck: Adjusted subject] Signed-off-by: Guenter Roeck