blob: cecb99618b907984fa4115fda8f99b48d945b458 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
#!/bin/bash -e
# Initialize for step motor of sled:
# Enable pwm and setup pwm duty
# Setup gpio pins for step motor control
# Moving step motor back to initial position
export PATH=$PATH:/usr/libexec
PWM_BASE_ADDR="0x1e61"
DEV_FILE="/dev/mem"
CALIBRATE_TIMEOUT=120
#Get pwm register address for sledN
function get_pwm_offset() {
local offset=0
case $1 in
0)
offset="0080"
;;
1)
offset="0090"
;;
2)
offset="00a0"
;;
3)
offset="00b0"
;;
4)
offset="00c0"
;;
5)
offset="00d0"
;;
esac
echo ${PWM_BASE_ADDR}${offset}
}
#Get pwm duty register address for sledN
function get_duty_offset() {
local offset=0
case $1 in
0)
offset="0084"
;;
1)
offset="0094"
;;
2)
offset="00a4"
;;
3)
offset="00b4"
;;
4)
offset="00c4"
;;
5)
offset="00d4"
;;
esac
echo ${PWM_BASE_ADDR}${offset}
}
#Enable pwm for sledN
function open_pwm() {
local SLED_NUM="$1"
echo "Open pwm of sled$SLED_NUM"
#enable BMC PWM
if [ ! -c "$DEV_FILE" ]; then
mknod /dev/mem c 1 1
fi
PWM_OFFSET=$(get_pwm_offset "$SLED_NUM")
DUTY_OFFSET=$(get_duty_offset "$SLED_NUM")
echo "setting ${PWM_OFFSET} to 0x000113F3"
echo "setting ${DUTY_OFFSET} to 0xFF006400"
devmem "$PWM_OFFSET" 32 0x000113F3
devmem "$DUTY_OFFSET" 32 0xFF006400
}
function set_gpio()
{
NET_NAME=$1
OUT_VAL=$2
mapfile -t -d " " GPIO_INFO < <(gpiofind "$NET_NAME")
if [ "${#GPIO_INFO[@]}" -ne 2 ]; then
echo "set_gpio: can not find gpio, $NET_NAME"
return 1
fi
echo -n "set_gpio: set $NET_NAME = $OUT_VAL"
if ! gpioset "${GPIO_INFO[0]}" "${GPIO_INFO[1]%$'\n'}"="$OUT_VAL"; then
echo " failed"
return 1
fi
echo " success"
return 0
}
function get_gpio()
{
NET_NAME=$1
RET_VAL=2
mapfile -t -d " " GPIO_INFO < <(gpiofind "$NET_NAME")
if [ "${#GPIO_INFO[@]}" -ne 2 ]; then
echo "get_gpio: can not find gpio, $NET_NAME" >&2
return 1
fi
if ! RET_VAL=$(gpioget "${GPIO_INFO[0]}" "${GPIO_INFO[1]%$'\n'}") ; then
echo "get_gpio: get ${NET_NAME} failed" >&2
return 1
fi
echo "${RET_VAL}"
return 0
}
#Init gpio pins for step motor control
function init_gpios() {
echo "Init GPIOs:"
motor_ctrl_gpio_pins_names=( "SLED${1}_MD_STBY_RESET"
"SLED${1}_MD_IOEXP_EN_FAULT"
"SLED${1}_MD_DIR"
"SLED${1}_MD_DECAY"
"SLED${1}_MD_MODE1"
"SLED${1}_MD_MODE2"
"SLED${1}_MD_MODE3" )
for gpio_name in "${motor_ctrl_gpio_pins_names[@]}"; do
set_gpio "$gpio_name" 0
done
}
if [[ "$1" =~ ^(slot[0-5]{1})$ ]] || [[ "$1" =~ ^(sled[0-5]{1})$ ]]; then
SLED=$1
SLED_NUM=${SLED:4}
else
#show_usage
echo "invalid sled name: ${1}"
exit 1;
fi
#Check if sled is present
SLED_PRESENT=$(get_gpio "presence-sled${SLED_NUM}")
if [ "$SLED_PRESENT" != 0 ];then
echo "${SLED} is not present, skip motor initialize"
exit 1
fi
#Init gpios
init_gpios "$SLED_NUM"
#enable pwm
open_pwm "$SLED_NUM"
#SLED{N}_MS_DETECT1 (initial position)
DETECT_PIN1="SLED${SLED_NUM}_MS_DETECT1"
INIT_POS=$(get_gpio "$DETECT_PIN1")
if [ "$INIT_POS" -eq 1 ];then
time_count=0
echo "Making motor back to initial position..."
motor-ctrl "$SLED" r >/dev/null
while [ "$INIT_POS" -eq 1 ] ;do
INIT_POS=$(get_gpio "$DETECT_PIN1")
sleep 0.1
time_count=$(( time_count + 1 ))
if [ $time_count -gt $CALIBRATE_TIMEOUT ];then
echo "Error: Step motor run over 1 cycle but switch never triggered"
break
fi
done
motor-ctrl "$SLED" s >/dev/null
fi
if [ "$INIT_POS" -eq 0 ];then
echo "Motor calibrated to initial position."
exit 0
else
echo "Find motor initial position failed"
exit 1
fi
|