1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
|
/***************************************************************************/
/*
* sltimers.c -- generic ColdFire slice timer support.
*
* Copyright (C) 2009-2010, Philippe De Muyter <phdm@macqel.be>
* based on
* timers.c -- generic ColdFire hardware timer support.
* Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
*/
/***************************************************************************/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/profile.h>
#include <linux/clocksource.h>
#include <asm/io.h>
#include <asm/traps.h>
#include <asm/machdep.h>
#include <asm/coldfire.h>
#include <asm/mcfslt.h>
#include <asm/mcfsim.h>
/***************************************************************************/
#ifdef CONFIG_HIGHPROFILE
/*
* By default use Slice Timer 1 as the profiler clock timer.
*/
#define PA(a) (MCF_MBAR + MCFSLT_TIMER1 + (a))
/*
* Choose a reasonably fast profile timer. Make it an odd value to
* try and get good coverage of kernel operations.
*/
#define PROFILEHZ 1013
irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
{
/* Reset Slice Timer 1 */
__raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, PA(MCFSLT_SSR));
if (current->pid)
profile_tick(CPU_PROFILING);
return IRQ_HANDLED;
}
static struct irqaction mcfslt_profile_irq = {
.name = "profile timer",
.flags = IRQF_DISABLED | IRQF_TIMER,
.handler = mcfslt_profile_tick,
};
void mcfslt_profile_init(void)
{
printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
PROFILEHZ);
setup_irq(MCF_IRQ_PROFILER, &mcfslt_profile_irq);
/* Set up TIMER 2 as high speed profile clock */
__raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
__raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
PA(MCFSLT_SCR));
}
#endif /* CONFIG_HIGHPROFILE */
/***************************************************************************/
/*
* By default use Slice Timer 0 as the system clock timer.
*/
#define TA(a) (MCF_MBAR + MCFSLT_TIMER0 + (a))
static u32 mcfslt_cycles_per_jiffy;
static u32 mcfslt_cnt;
static irqreturn_t mcfslt_tick(int irq, void *dummy)
{
/* Reset Slice Timer 0 */
__raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, TA(MCFSLT_SSR));
mcfslt_cnt += mcfslt_cycles_per_jiffy;
return arch_timer_interrupt(irq, dummy);
}
static struct irqaction mcfslt_timer_irq = {
.name = "timer",
.flags = IRQF_DISABLED | IRQF_TIMER,
.handler = mcfslt_tick,
};
static cycle_t mcfslt_read_clk(struct clocksource *cs)
{
unsigned long flags;
u32 cycles, scnt;
local_irq_save(flags);
scnt = __raw_readl(TA(MCFSLT_SCNT));
cycles = mcfslt_cnt;
if (__raw_readl(TA(MCFSLT_SSR)) & MCFSLT_SSR_TE) {
cycles += mcfslt_cycles_per_jiffy;
scnt = __raw_readl(TA(MCFSLT_SCNT));
}
local_irq_restore(flags);
/* subtract because slice timers count down */
return cycles + ((mcfslt_cycles_per_jiffy - 1) - scnt);
}
static struct clocksource mcfslt_clk = {
.name = "slt",
.rating = 250,
.read = mcfslt_read_clk,
.mask = CLOCKSOURCE_MASK(32),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
};
void hw_timer_init(void)
{
mcfslt_cycles_per_jiffy = MCF_BUSCLK / HZ;
/*
* The coldfire slice timer (SLT) runs from STCNT to 0 included,
* then STCNT again and so on. It counts thus actually
* STCNT + 1 steps for 1 tick, not STCNT. So if you want
* n cycles, initialize STCNT with n - 1.
*/
__raw_writel(mcfslt_cycles_per_jiffy - 1, TA(MCFSLT_STCNT));
__raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
TA(MCFSLT_SCR));
/* initialize mcfslt_cnt knowing that slice timers count down */
mcfslt_cnt = mcfslt_cycles_per_jiffy;
setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
#ifdef CONFIG_HIGHPROFILE
mcfslt_profile_init();
#endif
}
|
