1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
|
Marvell Orion SPI device
Required properties:
- compatible : should be on of the following:
- "marvell,orion-spi" for the Orion, mv78x00, Kirkwood and Dove SoCs
- "marvell,armada-370-spi", for the Armada 370 SoCs
- "marvell,armada-375-spi", for the Armada 375 SoCs
- "marvell,armada-380-spi", for the Armada 38x SoCs
- "marvell,armada-390-spi", for the Armada 39x SoCs
- "marvell,armada-xp-spi", for the Armada XP SoCs
- reg : offset and length of the register set for the device.
This property can optionally have additional entries to configure
the SPI direct access mode that some of the Marvell SoCs support
additionally to the normal indirect access (PIO) mode. The values
for the MBus "target" and "attribute" are defined in the Marvell
SoC "Functional Specifications" Manual in the chapter "Marvell
Core Processor Address Decoding".
The eight register sets following the control registers refer to
chip-select lines 0 through 7 respectively.
- cell-index : Which of multiple SPI controllers is this.
Optional properties:
- interrupts : Is currently not used.
Example:
spi@10600 {
compatible = "marvell,orion-spi";
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
reg = <0x10600 0x28>;
interrupts = <23>;
status = "disabled";
};
Example with SPI direct mode support (optionally):
spi0: spi@10600 {
compatible = "marvell,orion-spi";
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>, /* control */
<MBUS_ID(0x01, 0x1e) 0 0xffffffff>, /* CS0 */
<MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
<MBUS_ID(0x01, 0x9e) 0 0xffffffff>, /* CS2 */
<MBUS_ID(0x01, 0xde) 0 0xffffffff>, /* CS3 */
<MBUS_ID(0x01, 0x1f) 0 0xffffffff>, /* CS4 */
<MBUS_ID(0x01, 0x5f) 0 0xffffffff>, /* CS5 */
<MBUS_ID(0x01, 0x9f) 0 0xffffffff>, /* CS6 */
<MBUS_ID(0x01, 0xdf) 0 0xffffffff>; /* CS7 */
interrupts = <23>;
status = "disabled";
};
To enable the direct mode, the board specific 'ranges' property in the
'soc' node needs to add the entries for the desired SPI controllers
and its chip-selects that are used in the direct mode instead of PIO
mode. Here an example for this (SPI controller 0, device 1 and SPI
controller 1, device 2 are used in direct mode. All other SPI device
are used in the default indirect (PIO) mode):
soc {
/*
* Enable the SPI direct access by configuring an entry
* here in the board-specific ranges property
*/
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000>, /* internal regs */
<MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>, /* BootROM */
<MBUS_ID(0x01, 0x5e) 0 0 0xf1100000 0x10000>, /* SPI0-DEV1 */
<MBUS_ID(0x01, 0x9a) 0 0 0xf1110000 0x10000>; /* SPI1-DEV2 */
For further information on the MBus bindings, please see the MBus
DT documentation:
Documentation/devicetree/bindings/bus/mvebu-mbus.txt
|
