From 79e498a9c7da0737829ff864aae44df434105676 Mon Sep 17 00:00:00 2001 From: Leonard Crestez Date: Wed, 31 May 2017 13:29:30 +0300 Subject: net: phy: micrel: Restore led_mode and clk_sel on resume These bits seem to be lost after a suspend/resume cycle so just set them again. Do this by splitting the handling of these bits into a function that is also called on resume. This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards. Signed-off-by: Leonard Crestez Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/micrel.c | 42 ++++++++++++++++++++++++++++-------------- 1 file changed, 28 insertions(+), 14 deletions(-) (limited to 'drivers/net/phy/micrel.c') diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index 6a5fd18f062c..b9252b8d81ff 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -268,23 +268,12 @@ out: return ret; } -static int kszphy_config_init(struct phy_device *phydev) +/* Some config bits need to be set again on resume, handle them here. */ +static int kszphy_config_reset(struct phy_device *phydev) { struct kszphy_priv *priv = phydev->priv; - const struct kszphy_type *type; int ret; - if (!priv) - return 0; - - type = priv->type; - - if (type->has_broadcast_disable) - kszphy_broadcast_disable(phydev); - - if (type->has_nand_tree_disable) - kszphy_nand_tree_disable(phydev); - if (priv->rmii_ref_clk_sel) { ret = kszphy_rmii_clk_sel(phydev, priv->rmii_ref_clk_sel_val); if (ret) { @@ -295,11 +284,30 @@ static int kszphy_config_init(struct phy_device *phydev) } if (priv->led_mode >= 0) - kszphy_setup_led(phydev, type->led_mode_reg, priv->led_mode); + kszphy_setup_led(phydev, priv->type->led_mode_reg, priv->led_mode); return 0; } +static int kszphy_config_init(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + const struct kszphy_type *type; + + if (!priv) + return 0; + + type = priv->type; + + if (type->has_broadcast_disable) + kszphy_broadcast_disable(phydev); + + if (type->has_nand_tree_disable) + kszphy_nand_tree_disable(phydev); + + return kszphy_config_reset(phydev); +} + static int ksz8041_config_init(struct phy_device *phydev) { struct device_node *of_node = phydev->mdio.dev.of_node; @@ -700,8 +708,14 @@ static int kszphy_suspend(struct phy_device *phydev) static int kszphy_resume(struct phy_device *phydev) { + int ret; + genphy_resume(phydev); + ret = kszphy_config_reset(phydev); + if (ret) + return ret; + /* Enable PHY Interrupts */ if (phy_interrupt_is_valid(phydev)) { phydev->interrupts = PHY_INTERRUPT_ENABLED; -- cgit v1.2.3 From b866203d872d5deeafcecd25ea429d6748b5bd56 Mon Sep 17 00:00:00 2001 From: Zach Brown Date: Tue, 20 Jun 2017 12:48:11 -0500 Subject: net/phy: micrel: configure intterupts after autoneg workaround The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an autoneg failure case by resetting the hardware. This turns off intterupts. Things will work themselves out if the phy polls, as it will figure out it's state during a poll. However if the phy uses only intterupts, the phy will stall, since interrupts are off. This patch fixes the issue by calling config_intr after resetting the phy. Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg ") Signed-off-by: Zach Brown Reviewed-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/micrel.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net/phy/micrel.c') diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index b9252b8d81ff..8b2038844ba9 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -619,6 +619,8 @@ static int ksz9031_read_status(struct phy_device *phydev) if ((regval & 0xFF) == 0xFF) { phy_init_hw(phydev); phydev->link = 0; + if (phydev->drv->config_intr && phy_interrupt_is_valid(phydev)) + phydev->drv->config_intr(phydev); } return 0; -- cgit v1.2.3