summaryrefslogtreecommitdiff
path: root/sound/pci/oxygen
AgeCommit message (Collapse)AuthorFilesLines
2009-09-28sound: oxygen: fix input monitor control namesClemens Ladisch1-8/+8
Insert "Playback" into the input monitor control names to prevent alsa-lib from treating these controls as global controls. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: add high-pass filter controlClemens Ladisch1-2/+71
Add a control that allows disabling the high-pass filter of the WM8785 ADC. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: add digital filter controlClemens Ladisch3-9/+223
Add a control to select between sharp and slow roll-of filter responses of the DACs. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: virtuoso: add PCM1796 oversampling controlClemens Ladisch1-25/+157
Add a control to increase the oversampling factor to 128x on cards with PCM1796 or PCM1792A DACs. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: allow custom MCLK ratesClemens Ladisch6-4/+19
Add a callback that allows model drivers to modify the default I2S MCLK rate. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: virtuoso: add headphone impedance controlClemens Ladisch1-11/+99
Add a mixer control to adjust the headphone amplifier output for headphones with different impedances. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: cache codec registersClemens Ladisch4-152/+250
Keep a cache of codec registers to avoid unnecessary writes. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: more hardware documentationClemens Ladisch4-0/+33
Add some comments describing the hardware pin routing. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: add stereo upmixing to center/LFE channelsClemens Ladisch4-21/+58
Add the possibility to route a mix of the two channels of stereo data to the center and LFE outputs. This is implemented only for models where the DACs support this, i.e., for the Xonar D1 and DX. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: better defaults for upmixing controlClemens Ladisch3-10/+3
On card models with two-channel outputs, the base driver can automatically disable the upmixing control so that the model drivers do not need to do this. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: virtuoso: fix Xonar Essence ST supportClemens Ladisch2-6/+190
The Essence ST uses the CS2000 chip to generate the DAC master clock, so we better initialize and program it appropriately. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: virtuoso: split virtuoso.cClemens Ladisch7-1092/+1290
The virtuoso.c file has become rather big. This patch splits it up so that only code for very similar card models is in one file. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: fix for PI7C9X110 compatibilityClemens Ladisch1-0/+23
If the card is used with a Pericom PI7C9X110 PCI-E/PCI bridge, reconfigure the latter's PCI buffering to fix an unknown problem. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-28sound: oxygen: do not try to restore nonexistent EEPROMClemens Ladisch1-1/+5
On cards where the EEPROM was deliberately omitted, we do not need to try to restore the EEPROM's contents. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-07sound: oxygen: work around MCE when changing volumeClemens Ladisch1-10/+1
When the volume is changed continuously (e.g., when the user drags a volume slider with the mouse), the driver does lots of I2C writes. Apparently, the sound chip can get confused when we poll the I2C status register too much, and fails to complete a read from it. On the PCI-E models, the PCI-E/PCI bridge gets upset by this and generates a machine check exception. To avoid this, this patch replaces the polling with an unconditional wait that is guaranteed to be long enough. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Tested-by: Johann Messner <johann.messner at jku.at> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-03sound: oxygen: handle cards with missing EEPROMClemens Ladisch1-0/+3
The card model detection code introduced in 2.6.30 that tries to work around partially broken EEPROM contents by reading the EEPROM directly does not handle cards where the EEPROM has been omitted. In this case, we have to use the default ID to allow the driver to load. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Reported-and-tested-by: Ozan Çağlayan <ozan@pardus.org.tr> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-09-01sound: oxygen: fix MCLK rate for 192 kHz playbackClemens Ladisch1-0/+2
Do not forget to program the MCLK ratio for the I2S output. Otherwise, the master clock frequency can be too high for the DACs at sample frequencies above 96 kHz. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-07-02sound: virtuoso: fix Xonar D1/DX silence after resumeClemens Ladisch1-0/+2
When resuming, we better take the DACs out of the reset state before trying to use them. Reference: kernel bug #13599 http://bugzilla.kernel.org/show_bug.cgi?id=13599 Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-06-25sound: oxygen: make mic volume control monoClemens Ladisch1-10/+18
The microphone input and its volume register have only one channel, so we have to make the corresponding mixer control a mono control. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-05-25sound: virtuoso: add Xonar Essence ST supportClemens Ladisch1-19/+41
Add support for the Asus Xonar Essence ST and its daughterboard. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-05-25sound: virtuoso: enable HDAV S/PDIF inputClemens Ladisch1-1/+2
The Xonar HDAV1.3 has a digital input jack, so enable the corresponding device. This is not related to the HDMI stuff, which stays unsupported. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-05-25sound: virtuoso: add another DX PCI IDClemens Ladisch1-0/+1
Add another PCI ID for a second revision of the Xonar DX. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-05-25sound: oxygen: reset DMA when stream is closedClemens Ladisch1-1/+5
When a PCM stream is closed, flush the corresponding DMA channel. Otherwise, the DMA controller would continue to output the last sample which would result in a DC offset on the output. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-03-09sound: oxygen: enable headphone output on Claro cardsClemens Ladisch1-10/+53
On the HT-Omega Claro (halo) sound cards, the headphone amplifier must be enabled explicitly by setting a GPIO bit. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-27sound: oxygen: zero-initialize model dataClemens Ladisch1-1/+1
Model drivers assume that model_data is zeroed, so we better use kzalloc() (like we did before when it was allocated together with the card structure). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-26sound: virtuoso: add Xonar Essence STX supportClemens Ladisch1-0/+192
Add support for the Asus Xonar Essence STX sound card. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-20sound: virtuoso: increase minimum volume to -60 dBClemens Ladisch1-7/+7
Use -60 dB as the minimum value of the master volume mixer control. While the DACs would support ranges down to about -120 dB, such attenuations are not useful in practice. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-20sound: oxygen: handle AK5385 ADC on Claro halo cardsClemens Ladisch1-0/+16
The HT-Omega Claro halo's ADC is an AK5385 instead of a WM8785, so we should handle the ADC parameters as we do with the X-Meridian. Using the code for the wrong ADC does not seem to have any audible effects, and the Windows driver does it, but it is nonetheless a good idea to run the AK5385 with an oversampling ratio that is not outside the documented limits. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19sound: oxygen: automatically restore overwritten EEPROMClemens Ladisch3-0/+48
If the EEPROM was partially overwritten (which seems to happen before the OS is booted), restore its entire contents by deducing it from the remaining information. This does not have any effect on the Linux driver, which works even with incomplete information in the EEPROM, but it makes other drivers work again. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19sound: oxygen: handle cards with broken EEPROMClemens Ladisch6-93/+179
Under as yet unknown circumstances, the first word of the sound card's EEPROM gets overwritten. When this has happened, we cannot rely on the subsystem IDs that the kernel reads from the PCI configuration registers. Instead, we read the IDs directly from the EEPROM and do the ID matching manually. Because the model-specific driver cannot determine the model before calling oxygen_pci_probe(), that function now gets a get_model() callback as parameter. The customizing of the model structure, which was formerly done by the probe() callback, also has moved into get_model(). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19sound: oxygen: use static driver nameClemens Ladisch1-2/+3
When allocating resources, use a fixed name instead of reading it from the model structure. This allows us to allocate the resources before the actual model is known. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19sound: oxygen: allocate model_data dynamicallyClemens Ladisch1-3/+11
Allocate the model-specific data dynamically instead of including it in the memory block of the card structure. This will allow us to determine the actual model after the card creation. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19sound: oxygen: make the owner module a parameter of the probe functionClemens Ladisch5-10/+6
Move the owner field out of the oxygen_model structure and make it a parameter of oxygen_pci_probe(), because the actual owner module does not depend on the card model. Furthermore, moving it out of the model structure allows us to create the card structure before the actual model is known. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-02-19Merge branch 'topic/snd_card_new-err' into topic/oxygenTakashi Iwai1-4/+4
2009-02-19sound: virtuoso: revert "do not overwrite EEPROM on Xonar D2/D2X"Clemens Ladisch1-13/+4
This reverts commit 7e86c0e6850504ec9516b953f316a47277825e33 ("do not overwrite EEPROM on Xonar D2/D2X") because it did not actually help with the problem. More user reports show that the overwriting of the EEPROM is not triggered by using this driver but by installing Linux, and that the installation of any other operating system (even one without any CMI8788 driver) has the same effect. In other words, the presence of this driver does not have any effect on the occurrence of the error. (So far, the available evidence seems to point to a BIOS bug.) Furthermore, it turns out that the EEPROM chip is protected against stray write commands by the command format and by requiring a separate write-enable command, so the error scenario in the previous commit (that SPI writes can be misinterpreted as an EEPROM write command) is not even theoretically possible. The mixer control that was removed as a consequence of the previous commit can only be partially emulated in userspace, which also means it cannot be seen be the in-kernel OSS API emulation, so it is better to revert that change. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-01-19sound: virtuoso: add newlineClemens Ladisch1-1/+1
Add a missing newline. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-01-19sound: virtuoso: enable UART on Xonar HDAV1.3Clemens Ladisch1-0/+1
This hardware has a better chance of working correctly if we don't forget to enable it. Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-01-15sound: virtuoso: do not overwrite EEPROM on Xonar D2/D2XClemens Ladisch1-4/+13
On the Asus Xonar D2 and D2X models, the SPI chip select signal for the fourth DAC shares its pin with the serial clock for the EEPROM that contains the PCI subdevice ID values. It appears that when DAC registers are written and some other unknown conditions occur (probably noise on the EEPROM's chip select line), the EEPROM gets overwritten with garbage, which makes it impossible to properly detect the card later. Therefore, we better avoid DAC register writes and make sure that the driver works with the DAC's registers' default values. Consequently, the sample format is now I2S instead of left-justified (no user-visible change), and the DAC's volume/mute registers cannot be used anymore (volume changes are now done by the software volume plugin). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2009-01-12ALSA: Convert to snd_card_create() in sound/pci/*Takashi Iwai1-4/+4
Convert from snd_card_new() to the new snd_card_create() function in sound/pci/*. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-28ALSA: oxygen: add Claro halo supportClemens Ladisch1-0/+4
Add support for the HT-Omega Claro halo (XT). Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-09-24ALSA: oxygen: wait for ACK when resetting UARTClemens Ladisch1-0/+1
After sending a reset command to the UART, wait some time for the ACK to be generated (and to be read and dropped by the interrupt handler) before sending the next command. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: virtuoso: add Xonar HDAV1.3 supportClemens Ladisch1-0/+251
Add support for the Asus Xonar HDAV1.3 and the Xonar HDAV1.3 Deluxe. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: oxygen: rename first PCM deviceClemens Ladisch1-2/+3
Rename the first PCM device from "Analog" to "Multichannel" because it can be used for HDMI output on the Xonar HDAV. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: virtuoso: rename AC97 callback functionClemens Ladisch1-3/+3
Rename the callback function that switches between line and mic inputs on the Xonar D1 because it is also usable on other models. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: virtuoso: make number of PCM1796 DACs configurableClemens Ladisch1-4/+15
Do not use a hardcoded number when iterating over the PCM1796 DACs to allow for cards with a different number of analog output channels. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: virtuoso: allow I2C-connected PCM1796Clemens Ladisch1-2/+19
Add support for PCM1796 chips that are connected with an I2C bus instead of SPI. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: oxygen: add self-documenting functionsClemens Ladisch3-7/+32
Introduce some trivial functions to better document the relationships of the various model callbacks. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: oxygen: add UART I/O functionsClemens Ladisch3-2/+57
Add functions to allow model drivers to communicate with external chips by doing I/O with the not-used-for-MIDI UART. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: oxygen: configure MIDI via device_configClemens Ladisch4-11/+24
To enable the MIDI port, model drivers must now set flags in device_config, not only in misc_flags. This allows model drivers to enable the UART without creating an ALSA MIDI device. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
2008-09-22ALSA: oxygen: rename pcm_dev_cfgClemens Ladisch7-40/+40
Rename the pcm_dev_cfg field to device_config because there will be additional flags that do not describe PCM devices. Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-28 06:05:35 +0300