| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
virtio-mem wants to offline and remove a memory block once it unplugged
all subblocks (e.g., using alloc_contig_range()). Let's provide
an interface to do that from a driver. virtio-mem already supports to
offline partially unplugged memory blocks. Offlining a fully unplugged
memory block will not require to migrate any pages. All unplugged
subblocks are PageOffline() and have a reference count of 0 - so
offlining code will simply skip them.
All we need is an interface to offline and remove the memory from kernel
module context, where we don't have access to the memory block devices
(esp. find_memory_block() and device_offline()) and the device hotplug
lock.
To keep things simple, allow to only work on a single memory block.
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: Oscar Salvador <osalvador@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Wei Yang <richard.weiyang@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Qian Cai <cai@lca.pw>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200507140139.17083-9-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
virtio-mem wants to allow to offline memory blocks of which some parts
were unplugged (allocated via alloc_contig_range()), especially, to later
offline and remove completely unplugged memory blocks. The important part
is that PageOffline() has to remain set until the section is offline, so
these pages will never get accessed (e.g., when dumping). The pages should
not be handed back to the buddy (which would require clearing PageOffline()
and result in issues if offlining fails and the pages are suddenly in the
buddy).
Let's allow to do that by allowing to isolate any PageOffline() page
when offlining. This way, we can reach the memory hotplug notifier
MEM_GOING_OFFLINE, where the driver can signal that he is fine with
offlining this page by dropping its reference count. PageOffline() pages
with a reference count of 0 can then be skipped when offlining the
pages (like if they were free, however they are not in the buddy).
Anybody who uses PageOffline() pages and does not agree to offline them
(e.g., Hyper-V balloon, XEN balloon, VMWare balloon for 2MB pages) will not
decrement the reference count and make offlining fail when trying to
migrate such an unmovable page. So there should be no observable change.
Same applies to balloon compaction users (movable PageOffline() pages), the
pages will simply be migrated.
Note 1: If offlining fails, a driver has to increment the reference
count again in MEM_CANCEL_OFFLINE.
Note 2: A driver that makes use of this has to be aware that re-onlining
the memory block has to be handled by hooking into onlining code
(online_page_callback_t), resetting the page PageOffline() and
not giving them to the buddy.
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Anthony Yznaga <anthony.yznaga@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Pingfan Liu <kernelfans@gmail.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200507140139.17083-7-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We also want to unplug online memory (contained in online memory blocks
and, therefore, managed by the buddy), and eventually replug it later.
When requested to unplug memory, we use alloc_contig_range() to allocate
subblocks in online memory blocks (so we are the owner) and send them to
our hypervisor. When requested to plug memory, we can replug such memory
using free_contig_range() after asking our hypervisor.
We also want to mark all allocated pages PG_offline, so nobody will
touch them. To differentiate pages that were never onlined when
onlining the memory block from pages allocated via alloc_contig_range(), we
use PageDirty(). Based on this flag, virtio_mem_fake_online() can either
online the pages for the first time or use free_contig_range().
It is worth noting that there are no guarantees on how much memory can
actually get unplugged again. All device memory might completely be
fragmented with unmovable data, such that no subblock can get unplugged.
We are not touching the ZONE_MOVABLE. If memory is onlined to the
ZONE_MOVABLE, it can only get unplugged after that memory was offlined
manually by user space. In normal operation, virtio-mem memory is
suggested to be onlined to ZONE_NORMAL. In the future, we will try to
make unplug more likely to succeed.
Add a module parameter to control if online memory shall be touched.
As we want to access alloc_contig_range()/free_contig_range() from
kernel module context, export the symbols.
Note: Whenever virtio-mem uses alloc_contig_range(), all affected pages
are on the same node, in the same zone, and contain no holes.
Acked-by: Michal Hocko <mhocko@suse.com> # to export contig range allocator API
Tested-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20200507140139.17083-6-david@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Merge more updates from Andrew Morton:
"More mm/ work, plenty more to come
Subsystems affected by this patch series: slub, memcg, gup, kasan,
pagealloc, hugetlb, vmscan, tools, mempolicy, memblock, hugetlbfs,
thp, mmap, kconfig"
* akpm: (131 commits)
arm64: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
x86: mm: use ARCH_HAS_DEBUG_WX instead of arch defined
riscv: support DEBUG_WX
mm: add DEBUG_WX support
drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup
mm/thp: rename pmd_mknotpresent() as pmd_mkinvalid()
powerpc/mm: drop platform defined pmd_mknotpresent()
mm: thp: don't need to drain lru cache when splitting and mlocking THP
hugetlbfs: get unmapped area below TASK_UNMAPPED_BASE for hugetlbfs
sparc32: register memory occupied by kernel as memblock.memory
include/linux/memblock.h: fix minor typo and unclear comment
mm, mempolicy: fix up gup usage in lookup_node
tools/vm/page_owner_sort.c: filter out unneeded line
mm: swap: memcg: fix memcg stats for huge pages
mm: swap: fix vmstats for huge pages
mm: vmscan: limit the range of LRU type balancing
mm: vmscan: reclaim writepage is IO cost
mm: vmscan: determine anon/file pressure balance at the reclaim root
mm: balance LRU lists based on relative thrashing
mm: only count actual rotations as LRU reclaim cost
...
|
|
Patch series "Extract DEBUG_WX to shared use".
Some architectures support DEBUG_WX function, it's verbatim from each
others, so extract to mm/Kconfig.debug for shared use.
PPC and ARM ports don't support generic page dumper yet, so we only
refine x86 and arm64 port in this patch series.
For RISC-V port, the DEBUG_WX support depends on other patches which
be merged already:
- RISC-V page table dumper
- Support strict kernel memory permissions for security
This patch (of 4):
Some architectures support DEBUG_WX function, it's verbatim from each
others. Extract to mm/Kconfig.debug for shared use.
[akpm@linux-foundation.org: reword text, per Will Deacon & Zong Li]
Link: http://lkml.kernel.org/r/20200427194245.oxRJKj3fn%25akpm@linux-foundation.org
[zong.li@sifive.com: remove the specific name of arm64]
Link: http://lkml.kernel.org/r/3a6a92ecedc54e1d0fc941398e63d504c2cd5611.1589178399.git.zong.li@sifive.com
[zong.li@sifive.com: add MMU dependency for DEBUG_WX]
Link: http://lkml.kernel.org/r/4a674ac7863ff39ca91847b10e51209771f99416.1589178399.git.zong.li@sifive.com
Suggested-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/cover.1587455584.git.zong.li@sifive.com
Link: http://lkml.kernel.org/r/23980cd0f0e5d79e24a92169116407c75bcc650d.1587455584.git.zong.li@sifive.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
pmd_present() is expected to test positive after pmdp_mknotpresent() as
the PMD entry still points to a valid huge page in memory.
pmdp_mknotpresent() implies that given PMD entry is just invalidated from
MMU perspective while still holding on to pmd_page() referred valid huge
page thus also clearing pmd_present() test. This creates the following
situation which is counter intuitive.
[pmd_present(pmd_mknotpresent(pmd)) = true]
This renames pmd_mknotpresent() as pmd_mkinvalid() reflecting the helper's
functionality more accurately while changing the above mentioned situation
as follows. This does not create any functional change.
[pmd_present(pmd_mkinvalid(pmd)) = true]
This is not applicable for platforms that define own pmdp_invalidate() via
__HAVE_ARCH_PMDP_INVALIDATE. Suggestion for renaming came during a
previous discussion here.
https://patchwork.kernel.org/patch/11019637/
[anshuman.khandual@arm.com: change pmd_mknotvalid() to pmd_mkinvalid() per Will]
Link: http://lkml.kernel.org/r/1587520326-10099-3-git-send-email-anshuman.khandual@arm.com
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Will Deacon <will@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Link: http://lkml.kernel.org/r/1584680057-13753-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 8f182270dfec ("mm/swap.c: flush lru pvecs on compound page
arrival") THP would not stay in pagevec anymore. So the optimization made
by commit d965432234db ("thp: increase split_huge_page() success rate")
doesn't make sense anymore, which tries to unpin munlocked THPs from
pagevec by draining pagevec.
Draining lru cache before isolating THP in mlock path is also unnecessary.
b676b293fb48 ("mm, thp: fix mapped pages avoiding unevictable list on
mlock") added it and 9a73f61bdb8a ("thp, mlock: do not mlock PTE-mapped
file huge pages") accidentally carried it over after the above
optimization went in.
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: http://lkml.kernel.org/r/1585946493-7531-1-git-send-email-yang.shi@linux.alibaba.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ba841078cd05 ("mm/mempolicy: Allow lookup_node() to handle fatal signal")
has added a special casing for 0 return value because that was a possible
gup return value when interrupted by fatal signal. This has been fixed by
ae46d2aa6a7f ("mm/gup: Let __get_user_pages_locked() return -EINTR for
fatal signal") in the mean time so ba841078cd05 can be reverted.
This patch however doesn't go all the way to revert it because the check
for 0 is wrong and confusing here. Firstly it is inherently unsafe to
access the page when get_user_pages_locked returns 0 (aka no page
returned).
Fortunatelly this will not happen because get_user_pages_locked will not
return 0 when nr_pages > 0 unless FOLL_NOWAIT is specified which is not
the case here. Document this potential error code in gup code while we
are at it.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Xu <peterx@redhat.com>
Link: http://lkml.kernel.org/r/20200421071026.18394-1-mhocko@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The commit 2262185c5b28 ("mm: per-cgroup memory reclaim stats") added
PGLAZYFREE, PGACTIVATE & PGDEACTIVATE stats for cgroups but missed
couple of places and PGLAZYFREE missed huge page handling. Fix that.
Also for PGLAZYFREE use the irq-unsafe function to update as the irq is
already disabled.
Fixes: 2262185c5b28 ("mm: per-cgroup memory reclaim stats")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: http://lkml.kernel.org/r/20200527182947.251343-1-shakeelb@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Many of the callbacks called by pagevec_lru_move_fn() does not correctly
update the vmstats for huge pages. Fix that. Also __pagevec_lru_add_fn()
use the irq-unsafe alternative to update the stat as the irqs are
already disabled.
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Link: http://lkml.kernel.org/r/20200527182916.249910-1-shakeelb@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When LRU cost only shows up on one list, we abruptly stop scanning that
list altogether. That's an extreme reaction: by the time the other list
starts thrashing and the pendulum swings back, we may have no recent age
information on the first list anymore, and we could have significant
latencies until the scanner has caught up.
Soften this change in the feedback system by ensuring that no list
receives less than a third of overall pressure, and only distribute the
other 66% according to LRU cost. This ensures that we maintain a minimum
rate of aging on the entire workingset while it's being pressured, while
still allowing a generous rate of convergence when the relative sizes of
the lists need to adjust.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-15-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The VM tries to balance reclaim pressure between anon and file so as to
reduce the amount of IO incurred due to the memory shortage. It already
counts refaults and swapins, but in addition it should also count
writepage calls during reclaim.
For swap, this is obvious: it's IO that wouldn't have occurred if the
anonymous memory hadn't been under memory pressure. From a relative
balancing point of view this makes sense as well: even if anon is cold and
reclaimable, a cache that isn't thrashing may have equally cold pages that
don't require IO to reclaim.
For file writeback, it's trickier: some of the reclaim writepage IO would
have likely occurred anyway due to dirty expiration. But not all of it -
premature writeback reduces batching and generates additional writes.
Since the flushers are already woken up by the time the VM starts writing
cache pages one by one, let's assume that we'e likely causing writes that
wouldn't have happened without memory pressure. In addition, the per-page
cost of IO would have probably been much cheaper if written in larger
batches from the flusher thread rather than the single-page-writes from
kswapd.
For our purposes - getting the trend right to accelerate convergence on a
stable state that doesn't require paging at all - this is sufficiently
accurate. If we later wanted to optimize for sustained thrashing, we can
still refine the measurements.
Count all writepage calls from kswapd as IO cost toward the LRU that the
page belongs to.
Why do this dynamically? Don't we know in advance that anon pages require
IO to reclaim, and so could build in a static bias?
First, scanning is not the same as reclaiming. If all the anon pages are
referenced, we may not swap for a while just because we're scanning the
anon list. During this time, however, it's important that we age
anonymous memory and the page cache at the same rate so that their
hot-cold gradients are comparable. Everything else being equal, we still
want to reclaim the coldest memory overall.
Second, we keep copies in swap unless the page changes. If there is
swap-backed data that's mostly read (tmpfs file) and has been swapped out
before, we can reclaim it without incurring additional IO.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-14-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We split the LRU lists into anon and file, and we rebalance the scan
pressure between them when one of them begins thrashing: if the file cache
experiences workingset refaults, we increase the pressure on anonymous
pages; if the workload is stalled on swapins, we increase the pressure on
the file cache instead.
With cgroups and their nested LRU lists, we currently don't do this
correctly. While recursive cgroup reclaim establishes a relative LRU
order among the pages of all involved cgroups, LRU pressure balancing is
done on an individual cgroup LRU level. As a result, when one cgroup is
thrashing on the filesystem cache while a sibling may have cold anonymous
pages, pressure doesn't get equalized between them.
This patch moves LRU balancing decision to the root of reclaim - the same
level where the LRU order is established.
It does this by tracking LRU cost recursively, so that every level of the
cgroup tree knows the aggregate LRU cost of all memory within its domain.
When the page scanner calculates the scan balance for any given individual
cgroup's LRU list, it uses the values from the ancestor cgroup that
initiated the reclaim cycle.
If one sibling is then thrashing on the cache, it will tip the pressure
balance inside its ancestors, and the next hierarchical reclaim iteration
will go more after the anon pages in the tree.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-13-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since the LRUs were split into anon and file lists, the VM has been
balancing between page cache and anonymous pages based on per-list ratios
of scanned vs. rotated pages. In most cases that tips page reclaim
towards the list that is easier to reclaim and has the fewest actively
used pages, but there are a few problems with it:
1. Refaults and LRU rotations are weighted the same way, even though
one costs IO and the other costs a bit of CPU.
2. The less we scan an LRU list based on already observed rotations,
the more we increase the sampling interval for new references, and
rotations become even more likely on that list. This can enter a
death spiral in which we stop looking at one list completely until
the other one is all but annihilated by page reclaim.
Since commit a528910e12ec ("mm: thrash detection-based file cache sizing")
we have refault detection for the page cache. Along with swapin events,
they are good indicators of when the file or anon list, respectively, is
too small for its workingset and needs to grow.
For example, if the page cache is thrashing, the cache pages need more
time in memory, while there may be colder pages on the anonymous list.
Likewise, if swapped pages are faulting back in, it indicates that we
reclaim anonymous pages too aggressively and should back off.
Replace LRU rotations with refaults and swapins as the basis for relative
reclaim cost of the two LRUs. This will have the VM target list balances
that incur the least amount of IO on aggregate.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-12-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When shrinking the active file list we rotate referenced pages only when
they're in an executable mapping. The others get deactivated. When it
comes to balancing scan pressure, though, we count all referenced pages as
rotated, even the deactivated ones. Yet they do not carry the same cost
to the system: the deactivated page *might* refault later on, but the
deactivation is tangible progress toward freeing pages; rotations on the
other hand cost time and effort without getting any closer to freeing
memory.
Don't treat both events as equal. The following patch will hook up LRU
balancing to cache and anon refaults, which are a much more concrete cost
signal for reclaiming one list over the other. Thus, remove the maybe-IO
cost bias from page references, and only note the CPU cost for actual
rotations that prevent the pages from getting reclaimed.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-11-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Operations like MADV_FREE, FADV_DONTNEED etc. currently move any affected
active pages to the inactive list to accelerate their reclaim (good) but
also steer page reclaim toward that LRU type, or away from the other
(bad).
The reason why this is undesirable is that such operations are not part of
the regular page aging cycle, and rather a fluke that doesn't say much
about the remaining pages on that list; they might all be in heavy use,
and once the chunk of easy victims has been purged, the VM continues to
apply elevated pressure on those remaining hot pages. The other LRU,
meanwhile, might have easily reclaimable pages, and there was never a need
to steer away from it in the first place.
As the previous patch outlined, we should focus on recording actually
observed cost to steer the balance rather than speculating about the
potential value of one LRU list over the other. In that spirit, leave
explicitely deactivated pages to the LRU algorithm to pick up, and let
rotations decide which list is the easiest to reclaim.
[cai@lca.pw: fix set-but-not-used warning]
Link: http://lkml.kernel.org/r/20200522133335.GA624@Qians-MacBook-Air.local
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Qian Cai <cai@lca.pw>
Link: http://lkml.kernel.org/r/20200520232525.798933-10-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, scan pressure between the anon and file LRU lists is balanced
based on a mixture of reclaim efficiency and a somewhat vague notion of
"value" of having certain pages in memory over others. That concept of
value is problematic, because it has caused us to count any event that
remotely makes one LRU list more or less preferrable for reclaim, even
when these events are not directly comparable and impose very different
costs on the system. One example is referenced file pages that we still
deactivate and referenced anonymous pages that we actually rotate back to
the head of the list.
There is also conceptual overlap with the LRU algorithm itself. By
rotating recently used pages instead of reclaiming them, the algorithm
already biases the applied scan pressure based on page value. Thus, when
rebalancing scan pressure due to rotations, we should think of reclaim
cost, and leave assessing the page value to the LRU algorithm.
Lastly, considering both value-increasing as well as value-decreasing
events can sometimes cause the same type of event to be counted twice,
i.e. how rotating a page increases the LRU value, while reclaiming it
succesfully decreases the value. In itself this will balance out fine,
but it quietly skews the impact of events that are only recorded once.
The abstract metric of "value", the murky relationship with the LRU
algorithm, and accounting both negative and positive events make the
current pressure balancing model hard to reason about and modify.
This patch switches to a balancing model of accounting the concrete,
actually observed cost of reclaiming one LRU over another. For now, that
cost includes pages that are scanned but rotated back to the list head.
Subsequent patches will add consideration for IO caused by refaulting of
recently evicted pages.
Replace struct zone_reclaim_stat with two cost counters in the lruvec, and
make everything that affects cost go through a new lru_note_cost()
function.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-9-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we calculate the relative scan pressure between the anon and file LRU
lists, we have to assume that reclaim_stat can contain zeroes. To avoid
div0 crashes, we add 1 to all denominators like so:
anon_prio = swappiness;
file_prio = 200 - anon_prio;
[...]
/*
* The amount of pressure on anon vs file pages is inversely
* proportional to the fraction of recently scanned pages on
* each list that were recently referenced and in active use.
*/
ap = anon_prio * (reclaim_stat->recent_scanned[0] + 1);
ap /= reclaim_stat->recent_rotated[0] + 1;
fp = file_prio * (reclaim_stat->recent_scanned[1] + 1);
fp /= reclaim_stat->recent_rotated[1] + 1;
spin_unlock_irq(&pgdat->lru_lock);
fraction[0] = ap;
fraction[1] = fp;
denominator = ap + fp + 1;
While reclaim_stat can contain 0, it's not actually possible for ap + fp
to be 0. One of anon_prio or file_prio could be zero, but they must still
add up to 200. And the reclaim_stat fraction, due to the +1 in there, is
always at least 1. So if one of the two numerators is 0, the other one
can't be. ap + fp is always at least 1. Drop the + 1.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-8-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When the splitlru patches divided page cache and swap-backed pages into
separate LRU lists, the pressure balance between the lists was biased to
account for the fact that streaming IO can cause memory pressure with a
flood of pages that are used only once. New page cache additions would
tip the balance toward the file LRU, and repeat access would neutralize
that bias again. This ensured that page reclaim would always go for
used-once cache first.
Since e9868505987a ("mm,vmscan: only evict file pages when we have
plenty"), page reclaim generally skips over swap-backed memory entirely as
long as there is used-once cache present, and will apply the LRU balancing
when only repeatedly accessed cache pages are left - at which point the
previous use-once bias will have been neutralized. This makes the
use-once cache balancing bias unnecessary.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-7-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We activate cache refaults with reuse distances in pages smaller than the
size of the total cache. This allows new pages with competitive access
frequencies to establish themselves, as well as challenge and potentially
displace pages on the active list that have gone cold.
However, that assumes that active cache can only replace other active
cache in a competition for the hottest memory. This is not a great
default assumption. The page cache might be thrashing while there are
enough completely cold and unused anonymous pages sitting around that we'd
only have to write to swap once to stop all IO from the cache.
Activate cache refaults when their reuse distance in pages is smaller than
the total userspace workingset, including anonymous pages.
Reclaim can still decide how to balance pressure among the two LRUs
depending on the IO situation. Rotational drives will prefer avoiding
random IO from swap and go harder after cache. But fundamentally, hot
cache should be able to compete with anon pages for a place in RAM.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-6-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
They're the same function, and for the purpose of all callers they are
equivalent to lru_cache_add().
[akpm@linux-foundation.org: fix it for local_lock changes]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-5-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the advent of fast random IO devices (SSDs, PMEM) and in-memory swap
devices such as zswap, it's possible for swap to be much faster than
filesystems, and for swapping to be preferable over thrashing filesystem
caches.
Allow setting swappiness - which defines the rough relative IO cost of
cache misses between page cache and swap-backed pages - to reflect such
situations by making the swap-preferred range configurable.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-4-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Having statistics on pages scanned and pages reclaimed for both anon and
file pages makes it easier to evaluate changes to LRU balancing.
While at it, clean up the stat-keeping mess for isolation, putback,
reclaim stats etc. a bit: first the physical LRU operation (isolation and
putback), followed by vmstats, reclaim_stats, and then vm events.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-3-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The reclaim code that balances between swapping and cache reclaim tries to
predict likely reuse based on in-memory reference patterns alone. This
works in many cases, but when it fails it cannot detect when the cache is
thrashing pathologically, or when we're in the middle of a swap storm.
The high seek cost of rotational drives under which the algorithm evolved
also meant that mistakes could quickly result in lockups from too
aggressive swapping (which is predominantly random IO). As a result, the
balancing code has been tuned over time to a point where it mostly goes
for page cache and defers swapping until the VM is under significant
memory pressure.
The resulting strategy doesn't make optimal caching decisions - where
optimal is the least amount of IO required to execute the workload.
The proliferation of fast random IO devices such as SSDs, in-memory
compression such as zswap, and persistent memory technologies on the
horizon, has made this undesirable behavior very noticable: Even in the
presence of large amounts of cold anonymous memory and a capable swap
device, the VM refuses to even seriously scan these pages, and can leave
the page cache thrashing needlessly.
This series sets out to address this. Since commit ("a528910e12ec mm:
thrash detection-based file cache sizing") we have exact tracking of
refault IO - the ultimate cost of reclaiming the wrong pages. This allows
us to use an IO cost based balancing model that is more aggressive about
scanning anonymous memory when the cache is thrashing, while being able to
avoid unnecessary swap storms.
These patches base the LRU balance on the rate of refaults on each list,
times the relative IO cost between swap device and filesystem
(swappiness), in order to optimize reclaim for least IO cost incurred.
History
I floated these changes in 2016. At the time they were incomplete and
full of workarounds due to a lack of infrastructure in the reclaim code:
We didn't have PageWorkingset, we didn't have hierarchical cgroup
statistics, and problems with the cgroup swap controller. As swapping
wasn't too high a priority then, the patches stalled out. With all
dependencies in place now, here we are again with much cleaner,
feature-complete patches.
I kept the acks for patches that stayed materially the same :-)
Below is a series of test results that demonstrate certain problematic
behavior of the current code, as well as showcase the new code's more
predictable and appropriate balancing decisions.
Test #1: No convergence
This test shows an edge case where the VM currently doesn't converge at
all on a new file workingset with a stale anon/tmpfs set.
The test sets up a cold anon set the size of 3/4 RAM, then tries to
establish a new file set half the size of RAM (flat access pattern).
The vanilla kernel refuses to even scan anon pages and never converges.
The file set is perpetually served from the filesystem.
The first test kernel is with the series up to the workingset patch
applied. This allows thrashing page cache to challenge the anonymous
workingset. The VM then scans the lists based on the current
scanned/rotated balancing algorithm. It converges on a stable state where
all cold anon pages are pushed out and the fileset is served entirely from
cache:
noconverge/5.7-rc5-mm noconverge/5.7-rc5-mm-workingset
Scanned 417719308.00 ( +0.00%) 64091155.00 ( -84.66%)
Reclaimed 417711094.00 ( +0.00%) 61640308.00 ( -85.24%)
Reclaim efficiency % 100.00 ( +0.00%) 96.18 ( -3.78%)
Scanned file 417719308.00 ( +0.00%) 59211118.00 ( -85.83%)
Scanned anon 0.00 ( +0.00%) 4880037.00 ( )
Swapouts 0.00 ( +0.00%) 2439957.00 ( )
Swapins 0.00 ( +0.00%) 257.00 ( )
Refaults 415246605.00 ( +0.00%) 59183722.00 ( -85.75%)
Restore refaults 0.00 ( +0.00%) 54988252.00 ( )
The second test kernel is with the full patch series applied, which
replaces the scanned/rotated ratios with refault/swapin rate-based
balancing. It evicts the cold anon pages more aggressively in the
presence of a thrashing cache and the absence of swapins, and so converges
with about 60% of the IO and reclaim activity:
noconverge/5.7-rc5-mm-workingset noconverge/5.7-rc5-mm-lrubalance
Scanned 64091155.00 ( +0.00%) 37579741.00 ( -41.37%)
Reclaimed 61640308.00 ( +0.00%) 35129293.00 ( -43.01%)
Reclaim efficiency % 96.18 ( +0.00%) 93.48 ( -2.78%)
Scanned file 59211118.00 ( +0.00%) 32708385.00 ( -44.76%)
Scanned anon 4880037.00 ( +0.00%) 4871356.00 ( -0.18%)
Swapouts 2439957.00 ( +0.00%) 2435565.00 ( -0.18%)
Swapins 257.00 ( +0.00%) 262.00 ( +1.94%)
Refaults 59183722.00 ( +0.00%) 32675667.00 ( -44.79%)
Restore refaults 54988252.00 ( +0.00%) 28480430.00 ( -48.21%)
We're triggering this case in host sideloading scenarios: When a host's
primary workload is not saturating the machine (primary load is usually
driven by user activity), we can optimistically sideload a batch job; if
user activity picks up and the primary workload needs the whole host
during this time, we freeze the sideload and rely on it getting pushed to
swap. Frequently that swapping doesn't happen and the completely inactive
sideload simply stays resident while the expanding primary worklad is
struggling to gain ground.
Test #2: Kernel build
This test is a a kernel build that is slightly memory-restricted (make -j4
inside a 400M cgroup).
Despite the very aggressive swapping of cold anon pages in test #1, this
test shows that the new kernel carefully balances swap against cache
refaults when both the file and the cache set are pressured.
It shows the patched kernel to be slightly better at finding the coldest
memory from the combined anon and file set to evict under pressure. The
result is lower aggregate reclaim and paging activity:
z 5.7-rc5-mm 5.7-rc5-mm-lrubalance
Real time 210.60 ( +0.00%) 210.97 ( +0.18%)
User time 745.42 ( +0.00%) 746.48 ( +0.14%)
System time 69.78 ( +0.00%) 69.79 ( +0.02%)
Scanned file 354682.00 ( +0.00%) 293661.00 ( -17.20%)
Scanned anon 465381.00 ( +0.00%) 378144.00 ( -18.75%)
Swapouts 185920.00 ( +0.00%) 147801.00 ( -20.50%)
Swapins 34583.00 ( +0.00%) 32491.00 ( -6.05%)
Refaults 212664.00 ( +0.00%) 172409.00 ( -18.93%)
Restore refaults 48861.00 ( +0.00%) 80091.00 ( +63.91%)
Total paging IO 433167.00 ( +0.00%) 352701.00 ( -18.58%)
Test #3: Overload
This next test is not about performance, but rather about the
predictability of the algorithm. The current balancing behavior doesn't
always lead to comprehensible results, which makes performance analysis
and parameter tuning (swappiness e.g.) very difficult.
The test shows the balancing behavior under equivalent anon and file
input. Anon and file sets are created of equal size (3/4 RAM), have the
same access patterns (a hot-cold gradient), and synchronized access rates.
Swappiness is raised from the default of 60 to 100 to indicate equal IO
cost between swap and cache.
With the vanilla balancing code, anon scans make up around 9% of the total
pages scanned, or a ~1:10 ratio. This is a surprisingly skewed ratio, and
it's an outcome that is hard to explain given the input parameters to the
VM.
The new balancing model targets a 1:2 balance: All else being equal,
reclaiming a file page costs one page IO - the refault; reclaiming an anon
page costs two IOs - the swapout and the swapin. In the test we observe a
~1:3 balance.
The scanned and paging IO numbers indicate that the anon LRU algorithm we
have in place right now does a slightly worse job at picking the coldest
pages compared to the file algorithm. There is ongoing work to improve
this, like Joonsoo's anon workingset patches; however, it's difficult to
compare the two aging strategies when the balancing between them is
behaving unintuitively.
The slightly less efficient anon reclaim results in a deviation from the
optimal 1:2 scan ratio we would like to see here - however, 1:3 is much
closer to what we'd want to see in this test than the vanilla kernel's
aging of 10+ cache pages for every anonymous one:
overload-100/5.7-rc5-mm-workingset overload-100/5.7-rc5-mm-lrubalance-realfile
Scanned 533633725.00 ( +0.00%) 595687785.00 ( +11.63%)
Reclaimed 494325440.00 ( +0.00%) 518154380.00 ( +4.82%)
Reclaim efficiency % 92.63 ( +0.00%) 86.98 ( -6.03%)
Scanned file 484532894.00 ( +0.00%) 456937722.00 ( -5.70%)
Scanned anon 49100831.00 ( +0.00%) 138750063.00 ( +182.58%)
Swapouts 8096423.00 ( +0.00%) 48982142.00 ( +504.98%)
Swapins 10027384.00 ( +0.00%) 62325044.00 ( +521.55%)
Refaults 479819973.00 ( +0.00%) 451309483.00 ( -5.94%)
Restore refaults 426422087.00 ( +0.00%) 399914067.00 ( -6.22%)
Total paging IO 497943780.00 ( +0.00%) 562616669.00 ( +12.99%)
Test #4: Parallel IO
It's important to note that these patches only affect the situation where
the kernel has to reclaim workingset memory, which is usually a
transitionary period. The vast majority of page reclaim occuring in a
system is from trimming the ever-expanding page cache.
These patches don't affect cache trimming behavior. We never swap as long
as we only have use-once cache moving through the file LRU, we only
consider swapping when the cache is actively thrashing.
The following test demonstrates this. It has an anon workingset that
takes up half of RAM and then writes a file that is twice the size of RAM
out to disk.
As the cache is funneled through the inactive file list, no anon pages are
scanned (aside from apparently some background noise of 10 pages):
5.7-rc5-mm 5.7-rc5-mm-lrubalance
Scanned 10714722.00 ( +0.00%) 10723445.00 ( +0.08%)
Reclaimed 10703596.00 ( +0.00%) 10712166.00 ( +0.08%)
Reclaim efficiency % 99.90 ( +0.00%) 99.89 ( -0.00%)
Scanned file 10714722.00 ( +0.00%) 10723435.00 ( +0.08%)
Scanned anon 0.00 ( +0.00%) 10.00 ( )
Swapouts 0.00 ( +0.00%) 7.00 ( )
Swapins 0.00 ( +0.00%) 0.00 ( +0.00%)
Refaults 92.00 ( +0.00%) 41.00 ( -54.84%)
Restore refaults 0.00 ( +0.00%) 0.00 ( +0.00%)
Total paging IO 92.00 ( +0.00%) 48.00 ( -47.31%)
This patch (of 14):
Currently, THP are counted as single pages until they are split right
before being swapped out. However, at that point the VM is already in the
middle of reclaim, and adjusting the LRU balance then is useless.
Always account THP by the number of basepages, and remove the fixup from
the splitting path.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: http://lkml.kernel.org/r/20200520232525.798933-1-hannes@cmpxchg.org
Link: http://lkml.kernel.org/r/20200520232525.798933-2-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The previous patches have simplified the access rules around
page->mem_cgroup somewhat:
1. We never change page->mem_cgroup while the page is isolated by
somebody else. This was by far the biggest exception to our rules and
it didn't stop at lock_page() or lock_page_memcg().
2. We charge pages before they get put into page tables now, so the
somewhat fishy rule about "can be in page table as long as it's still
locked" is now gone and boiled down to having an exclusive reference to
the page.
Document the new rules. Any of the following will stabilize the
page->mem_cgroup association:
- the page lock
- LRU isolation
- lock_page_memcg()
- exclusive access to the page
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-20-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Swapin faults were the last event to charge pages after they had already
been put on the LRU list. Now that we charge directly on swapin, the
lrucare portion of the charge code is unused.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Shakeel Butt <shakeelb@google.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-19-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Right now, users that are otherwise memory controlled can easily escape
their containment and allocate significant amounts of memory that they're
not being charged for. That's because swap readahead pages are not being
charged until somebody actually faults them into their page table. This
can be exploited with MADV_WILLNEED, which triggers arbitrary readahead
allocations without charging the pages.
There are additional problems with the delayed charging of swap pages:
1. To implement refault/workingset detection for anonymous pages, we
need to have a target LRU available at swapin time, but the LRU is not
determinable until the page has been charged.
2. To implement per-cgroup LRU locking, we need page->mem_cgroup to be
stable when the page is isolated from the LRU; otherwise, the locks
change under us. But swapcache gets charged after it's already on the
LRU, and even if we cannot isolate it ourselves (since charging is not
exactly optional).
The previous patch ensured we always maintain cgroup ownership records for
swap pages. This patch moves the swapcache charging point from the fault
handler to swapin time to fix all of the above problems.
v2: simplify swapin error checking (Joonsoo)
[hughd@google.com: fix livelock in __read_swap_cache_async()]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2005212246080.8458@eggly.anvils
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-17-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Without swap page tracking, users that are otherwise memory controlled can
easily escape their containment and allocate significant amounts of memory
that they're not being charged for. That's because swap does readahead,
but without the cgroup records of who owned the page at swapout, readahead
pages don't get charged until somebody actually faults them into their
page table and we can identify an owner task. This can be maliciously
exploited with MADV_WILLNEED, which triggers arbitrary readahead
allocations without charging the pages.
Make swap swap page tracking an integral part of memcg and remove the
Kconfig options. In the first place, it was only made configurable to
allow users to save some memory. But the overhead of tracking cgroup
ownership per swap page is minimal - 2 byte per page, or 512k per 1G of
swap, or 0.04%. Saving that at the expense of broken containment
semantics is not something we should present as a coequal option.
The swapaccount=0 boot option will continue to exist, and it will
eliminate the page_counter overhead and hide the swap control files, but
it won't disable swap slot ownership tracking.
This patch makes sure we always have the cgroup records at swapin time;
the next patch will fix the actual bug by charging readahead swap pages at
swapin time rather than at fault time.
v2: fix double swap charge bug in cgroup1/cgroup2 code gating
[hannes@cmpxchg.org: fix crash with cgroup_disable=memory]
Link: http://lkml.kernel.org/r/20200521215855.GB815153@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: http://lkml.kernel.org/r/20200508183105.225460-16-hannes@cmpxchg.org
Debugged-by: Hugh Dickins <hughd@google.com>
Debugged-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A few cleanups to streamline the swap controller setup:
- Replace the do_swap_account flag with cgroup_memory_noswap. This
brings it in line with other functionality that is usually available
unless explicitly opted out of - nosocket, nokmem.
- Remove the really_do_swap_account flag that stores the boot option
and is later used to switch the do_swap_account. It's not clear why
this indirection is/was necessary. Use do_swap_account directly.
- Minor coding style polishing
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-15-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are no more users. RIP in peace.
[arnd@arndb.de: fix an unused-function warning]
Link: http://lkml.kernel.org/r/20200528095640.151454-1-arnd@arndb.de
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-14-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the page->mapping requirement gone from memcg, we can charge anon and
file-thp pages in one single step, right after they're allocated.
This removes two out of three API calls - especially the tricky commit
step that needed to happen at just the right time between when the page is
"set up" and when it's "published" - somewhat vague and fluid concepts
that varied by page type. All we need is a freshly allocated page and a
memcg context to charge.
v2: prevent double charges on pre-allocated hugepages in khugepaged
[hannes@cmpxchg.org: Fix crash - *hpage could be ERR_PTR instead of NULL]
Link: http://lkml.kernel.org/r/20200512215813.GA487759@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Qian Cai <cai@lca.pw>
Link: http://lkml.kernel.org/r/20200508183105.225460-13-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With rmap memcg locking already in place for NR_ANON_MAPPED, it's just a
small step to remove the MEMCG_RSS_HUGE wart and switch memcg to the
native NR_ANON_THPS accounting sites.
[hannes@cmpxchg.org: fixes]
Link: http://lkml.kernel.org/r/20200512121750.GA397968@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> [build-tested]
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-12-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Memcg maintains a private MEMCG_RSS counter. This divergence from the
generic VM accounting means unnecessary code overhead, and creates a
dependency for memcg that page->mapping is set up at the time of charging,
so that page types can be told apart.
Convert the generic accounting sites to mod_lruvec_page_state and friends
to maintain the per-cgroup vmstat counter of NR_ANON_MAPPED. We use
lock_page_memcg() to stabilize page->mem_cgroup during rmap changes, the
same way we do for NR_FILE_MAPPED.
With the previous patch removing MEMCG_CACHE and the private NR_SHMEM
counter, this patch finally eliminates the need to have page->mapping set
up at charge time. However, we need to have page->mem_cgroup set up by
the time rmap runs and does the accounting, so switch the commit and the
rmap callbacks around.
v2: fix temporary accounting bug by switching rmap<->commit (Joonsoo)
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-11-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Memcg maintains private MEMCG_CACHE and NR_SHMEM counters. This
divergence from the generic VM accounting means unnecessary code overhead,
and creates a dependency for memcg that page->mapping is set up at the
time of charging, so that page types can be told apart.
Convert the generic accounting sites to mod_lruvec_page_state and friends
to maintain the per-cgroup vmstat counters of NR_FILE_PAGES and NR_SHMEM.
The page is already locked in these places, so page->mem_cgroup is stable;
we only need minimal tweaks of two mem_cgroup_migrate() calls to ensure
it's set up in time.
Then replace MEMCG_CACHE with NR_FILE_PAGES and delete the private
NR_SHMEM accounting sites.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-10-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Anonymous compound pages can be mapped by ptes, which means that if we
want to track NR_MAPPED_ANON, NR_ANON_THPS on a per-cgroup basis, we have
to be prepared to see tail pages in our accounting functions.
Make mod_lruvec_page_state() and lock_page_memcg() deal with tail pages
correctly, namely by redirecting to the head page which has the
page->mem_cgroup set up.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-9-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When memcg uses the generic vmstat counters, it doesn't need to do
anything at charging and uncharging time. It does, however, need to
migrate counts when pages move to a different cgroup in move_account.
Prepare the move_account function for the arrival of NR_FILE_PAGES,
NR_ANON_MAPPED, NR_ANON_THPS etc. by having a branch for files and a
branch for anon, which can then divided into sub-branches.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-8-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The uncharge batching code adds up the anon, file, kmem counts to
determine the total number of pages to uncharge and references to drop.
But the next patches will remove the anon and file counters.
Maintain an aggregate nr_pages in the uncharge_gather struct.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-7-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The try/commit/cancel protocol that memcg uses dates back to when pages
used to be uncharged upon removal from the page cache, and thus couldn't
be committed before the insertion had succeeded. Nowadays, pages are
uncharged when they are physically freed; it doesn't matter whether the
insertion was successful or not. For the page cache, the transaction
dance has become unnecessary.
Introduce a mem_cgroup_charge() function that simply charges a newly
allocated page to a cgroup and sets up page->mem_cgroup in one single
step. If the insertion fails, the caller doesn't have to do anything but
free/put the page.
Then switch the page cache over to this new API.
Subsequent patches will also convert anon pages, but it needs a bit more
prep work. Right now, memcg depends on page->mapping being already set up
at the time of charging, so that it can maintain its own MEMCG_CACHE and
MEMCG_RSS counters. For anon, page->mapping is set under the same pte
lock under which the page is publishd, so a single charge point that can
block doesn't work there just yet.
The following prep patches will replace the private memcg counters with
the generic vmstat counters, thus removing the page->mapping dependency,
then complete the transition to the new single-point charge API and delete
the old transactional scheme.
v2: leave shmem swapcache when charging fails to avoid double IO (Joonsoo)
v3: rebase on preceeding shmem simplification patch
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-6-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The cgroup swaprate throttling is about matching new anon allocations to
the rate of available IO when that is being throttled. It's the io
controller hooking into the VM, rather than a memory controller thing.
Rename mem_cgroup_throttle_swaprate() to cgroup_throttle_swaprate(), and
drop the @memcg argument which is only used to check whether the preceding
page charge has succeeded and the fault is proceeding.
We could decouple the call from mem_cgroup_try_charge() here as well, but
that would cause unnecessary churn: the following patches convert all
callsites to a new charge API and we'll decouple as we go along.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-5-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 215c02bc33bb ("tmpfs: fix shmem_getpage_gfp() VM_BUG_ON")
recognized that hole punching can race with swapin and removed the
BUG_ON() for a truncated entry from the swapin path.
The patch also added a swapcache deletion to optimize this rare case:
Since swapin has the page locked, and free_swap_and_cache() merely
trylocks, this situation can leave the page stranded in swapcache.
Usually, page reclaim picks up stale swapcache pages, and the race can
happen at any other time when the page is locked. (The same happens for
non-shmem swapin racing with page table zapping.) The thinking here was:
we already observed the race and we have the page locked, we may as well
do the cleanup instead of waiting for reclaim.
However, this optimization complicates the next patch which moves the
cgroup charging code around. As this is just a minor speedup for a race
condition that is so rare that it required a fuzzer to trigger the
original BUG_ON(), it's no longer worth the complications.
Suggested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200511181056.GA339505@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The memcg charging API carries a boolean @compound parameter that tells
whether the page we're dealing with is a hugepage.
mem_cgroup_commit_charge() has another boolean @lrucare that indicates
whether the page needs LRU locking or not while charging. The majority of
callsites know those parameters at compile time, which results in a lot of
naked "false, false" argument lists. This makes for cryptic code and is a
breeding ground for subtle mistakes.
Thankfully, the huge page state can be inferred from the page itself and
doesn't need to be passed along. This is safe because charging completes
before the page is published and somebody may split it.
Simplify the callsites by removing @compound, and let memcg infer the
state by using hpage_nr_pages() unconditionally. That function does
PageTransHuge() to identify huge pages, which also helpfully asserts that
nobody passes in tail pages by accident.
The following patches will introduce a new charging API, best not to carry
over unnecessary weight.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-4-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The move_lock is a per-memcg lock, but the VM accounting code that needs
to acquire it comes from the page and follows page->mem_cgroup under RCU
protection. That means that the page becomes unlocked not when we drop
the move_lock, but when we update page->mem_cgroup. And that assignment
doesn't imply any memory ordering. If that pointer write gets reordered
against the reads of the page state - page_mapped, PageDirty etc. the
state may change while we rely on it being stable and we can end up
corrupting the counters.
Place an SMP memory barrier to make sure we're done with all page state by
the time the new page->mem_cgroup becomes visible.
Also replace the open-coded move_lock with a lock_page_memcg() to make it
more obvious what we're serializing against.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Alex Shi <alex.shi@linux.alibaba.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-3-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm: memcontrol: charge swapin pages on instantiation", v2.
This patch series reworks memcg to charge swapin pages directly at
swapin time, rather than at fault time, which may be much later, or
not happen at all.
Changes in version 2:
- prevent double charges on pre-allocated hugepages in khugepaged
- leave shmem swapcache when charging fails to avoid double IO (Joonsoo)
- fix temporary accounting bug by switching rmap<->commit (Joonsoo)
- fix double swap charge bug in cgroup1/cgroup2 code gating
- simplify swapin error checking (Joonsoo)
- mm: memcontrol: document the new swap control behavior (Alex)
- review tags
The delayed swapin charging scheme we have right now causes problems:
- Alex's per-cgroup lru_lock patches rely on pages that have been
isolated from the LRU to have a stable page->mem_cgroup; otherwise
the lock may change underneath him. Swapcache pages are charged only
after they are added to the LRU, and charging doesn't follow the LRU
isolation protocol.
- Joonsoo's anon workingset patches need a suitable LRU at the time
the page enters the swap cache and displaces the non-resident
info. But the correct LRU is only available after charging.
- It's a containment hole / DoS vector. Users can trigger arbitrarily
large swap readahead using MADV_WILLNEED. The memory is never
charged unless somebody actually touches it.
- It complicates the page->mem_cgroup stabilization rules
In order to charge pages directly at swapin time, the memcg code base
needs to be prepared, and several overdue cleanups become a necessity:
To charge pages at swapin time, we need to always have cgroup
ownership tracking of swap records. We also cannot rely on
page->mapping to tell apart page types at charge time, because that's
only set up during a page fault.
To eliminate the page->mapping dependency, memcg needs to ditch its
private page type counters (MEMCG_CACHE, MEMCG_RSS, NR_SHMEM) in favor
of the generic vmstat counters and accounting sites, such as
NR_FILE_PAGES, NR_ANON_MAPPED etc.
To switch to generic vmstat counters, the charge sequence must be
adjusted such that page->mem_cgroup is set up by the time these
counters are modified.
The series is structured as follows:
1. Bug fixes
2. Decoupling charging from rmap
3. Swap controller integration into memcg
4. Direct swapin charging
This patch (of 19):
When replacing one page with another one in the cache, we have to decrease
the file count of the old page's NUMA node and increase the one of the new
NUMA node, otherwise the old node leaks the count and the new node
eventually underflows its counter.
Fixes: 74d609585d8b ("page cache: Add and replace pages using the XArray")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Roman Gushchin <guro@fb.com>
Link: http://lkml.kernel.org/r/20200508183105.225460-1-hannes@cmpxchg.org
Link: http://lkml.kernel.org/r/20200508183105.225460-2-hannes@cmpxchg.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
try_to_compact_zone() has been replaced by try_to_compact_pages(), which
is necessary to be updated in the comment of should_continue_reclaim().
Signed-off-by: Qiwu Chen <chenqiwu@xiaomi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20200501034907.22991-1-chenqiwu@xiaomi.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 3c710c1ad11b ("mm, vmscan extract shrink_page_list reclaim counters
into a struct") changed data type for the function, so changing return
type for funciton and its caller.
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Amit Sahrawat <a.sahrawat@samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Link: http://lkml.kernel.org/r/1588168259-25604-1-git-send-email-maninder1.s@samsung.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix an nr_isolate_* mismatch problem between cma and dirty lazyfree pages.
If try_to_unmap_one is used for reclaim and it detects a dirty lazyfree
page, then the lazyfree page is changed to a normal anon page having
SwapBacked by commit 802a3a92ad7a ("mm: reclaim MADV_FREE pages"). Even
with the change, reclaim context correctly counts isolated files because
it uses is_file_lru to distinguish file. And the change to anon is not
happened if try_to_unmap_one is used for migration. So migration context
like compaction also correctly counts isolated files even though it uses
page_is_file_lru insted of is_file_lru. Recently page_is_file_cache was
renamed to page_is_file_lru by commit 9de4f22a60f7 ("mm: code cleanup for
MADV_FREE").
But the nr_isolate_* mismatch problem happens on cma alloc. There is
reclaim_clean_pages_from_list which is being used only by cma. It was
introduced by commit 02c6de8d757c ("mm: cma: discard clean pages during
contiguous allocation instead of migration") to reclaim clean file pages
without migration. The cma alloc uses both reclaim_clean_pages_from_list
and migrate_pages, and it uses page_is_file_lru to count isolated files.
If there are dirty lazyfree pages allocated from cma memory region, the
pages are counted as isolated file at the beginging but are counted as
isolated anon after finished.
Mem-Info:
Node 0 active_anon:3045904kB inactive_anon:611448kB active_file:14892kB inactive_file:205636kB unevictable:10416kB isolated(anon):0kB isolated(file):37664kB mapped:630216kB dirty:384kB writeback:0kB shmem:42576kB writeback_tmp:0kB unstable:0kB all_unreclaimable? no
Like log above, there were too much isolated files, 37664kB, which
triggers too_many_isolated in reclaim even when there is no actually
isolated file in system wide. It could be reproducible by running two
programs, writing on MADV_FREE page and doing cma alloc, respectively.
Although isolated anon is 0, I found that the internal value of isolated
anon was the negative value of isolated file.
Fix this by compensating the isolated count for both LRU lists. Count
non-discarded lazyfree pages in shrink_page_list, then compensate the
counted number in reclaim_clean_pages_from_list.
Reported-by: Yong-Taek Lee <ytk.lee@samsung.com>
Suggested-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Jaewon Kim <jaewon31.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Shaohua Li <shli@fb.com>
Link: http://lkml.kernel.org/r/20200426011718.30246-1-jaewon31.kim@samsung.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We already defined the helper update_lru_size().
Let's use this to reduce code duplication.
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Link: http://lkml.kernel.org/r/20200331221550.1011-1-richard.weiyang@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
None of the three callers of get_compound_page_dtor() want to know the
value; they just want to call the function. Replace it with
destroy_compound_page() which calls the dtor for them.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: http://lkml.kernel.org/r/20200517105051.9352-1-willy@infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When huge_pte_offset() is called, the parameter sz can only be PUD_SIZE or
PMD_SIZE. If sz is PUD_SIZE and code can reach pud, then *pud must be
none, or normal hugetlb entry, or non-present (migration or hwpoisoned)
hugetlb entry, and we can directly return pud. When sz is PMD_SIZE, pud
must be none or present, and if code can reach pmd, we can directly return
pmd.
So after this patch the code is simplified by first check on the parameter
sz, and avoid unnecessary checks in current code. Same semantics of
existing code is maintained.
More details about relevant commits:
commit 9b19df292c66 ("mm/hugetlb.c: make huge_pte_offset() consistent
and document behaviour") changed the code path for pud and pmd handling,
see comments about why this patch intends to change it.
...
pud = pud_offset(p4d, addr);
if (sz != PUD_SIZE && pud_none(*pud)) // [1]
return NULL;
/* hugepage or swap? */
if (pud_huge(*pud) || !pud_present(*pud)) // [2]
return (pte_t *)pud;
pmd = pmd_offset(pud, addr);
if (sz != PMD_SIZE && pmd_none(*pmd)) // [3]
return NULL;
/* hugepage or swap? */
if (pmd_huge(*pmd) || !pmd_present(*pmd)) // [4]
return (pte_t *)pmd;
return NULL; // [5]
...
[1]: this is necessary, return NULL for sz == PMD_SIZE;
[2]: if sz == PUD_SIZE, all valid values of pud entry will cause return;
[3]: dead code, sz != PMD_SIZE never true;
[4]: all valid values of pmd entry will cause return;
[5]: dead code, because of check in [4].
Now, this patch combines [1] and [2] for pud, and combines [3], [4] and
[5] for pmd, so avoid unnecessary checks.
I don't try to catch any invalid values in page table entry, as that will
be checked by caller and avoid extra branch in this function. Also no
assert on sz must equal PUD_SIZE or PMD_SIZE, since this function only
call for hugetlb mapping.
For commit 3c1d7e6ccb64 ("mm/hugetlb: fix a addressing exception caused by
huge_pte_offset"), since we don't read the entry more than once now,
variable pud_entry and pmd_entry are not needed.
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Longpeng <longpeng2@huawei.com>
Link: http://lkml.kernel.org/r/1587794313-16849-1-git-send-email-lixinhai.lxh@gmail.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Previously, a check for hugepages_supported was added before processing
hugetlb command line parameters. On some architectures such as powerpc,
hugepages_supported() is not set to true until after command line
processing. Therefore, no hugetlb command line parameters would be
accepted.
Remove the additional checks for hugepages_supported. In hugetlb_init,
print a warning if !hugepages_supported and command line parameters were
specified.
Reported-by: Sandipan Das <sandipan.osd@gmail.com>
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/b1f04f9f-fa46-c2a0-7693-4a0679d2a1ee@oracle.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
