summaryrefslogtreecommitdiff
path: root/include/linux/perf
AgeCommit message (Collapse)AuthorFilesLines
2020-03-18arm64: perf: Add support for ARMv8.5-PMU 64-bit countersAndrew Murray1-0/+1
At present ARMv8 event counters are limited to 32-bits, though by using the CHAIN event it's possible to combine adjacent counters to achieve 64-bits. The perf config1:0 bit can be set to use such a configuration. With the introduction of ARMv8.5-PMU support, all event counters can now be used as 64-bit counters. Let's enable 64-bit event counters where support exists. Unless the user sets config1:0 we will adjust the counter value such that it overflows upon 32-bit overflow. This follows the same behaviour as the cycle counter which has always been (and remains) 64-bits. Signed-off-by: Andrew Murray <andrew.murray@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> [Mark: fix ID field names, compare with 8.5 value] Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2019-07-08Merge tag 'arm64-upstream' of ↵Linus Torvalds1-0/+2
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 updates from Catalin Marinas: - arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP} - Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to manage the permissions of executable vmalloc regions more strictly - Slight performance improvement by keeping softirqs enabled while touching the FPSIMD/SVE state (kernel_neon_begin/end) - Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new XAFLAG and AXFLAG instructions for floating point comparison flags manipulation) and FRINT (rounding floating point numbers to integers) - Re-instate ARM64_PSEUDO_NMI support which was previously marked as BROKEN due to some bugs (now fixed) - Improve parking of stopped CPUs and implement an arm64-specific panic_smp_self_stop() to avoid warning on not being able to stop secondary CPUs during panic - perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI platforms - perf: DDR performance monitor support for iMX8QXP - cache_line_size() can now be set from DT or ACPI/PPTT if provided to cope with a system cache info not exposed via the CPUID registers - Avoid warning on hardware cache line size greater than ARCH_DMA_MINALIGN if the system is fully coherent - arm64 do_page_fault() and hugetlb cleanups - Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep) - Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the 'arm_boot_flags' introduced in 5.1) - CONFIG_RANDOMIZE_BASE now enabled in defconfig - Allow the selection of ARM64_MODULE_PLTS, currently only done via RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill over into the vmalloc area - Make ZONE_DMA32 configurable * tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits) perf: arm_spe: Enable ACPI/Platform automatic module loading arm_pmu: acpi: spe: Add initial MADT/SPE probing ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens ACPI/PPTT: Modify node flag detection to find last IDENTICAL x86/entry: Simplify _TIF_SYSCALL_EMU handling arm64: rename dump_instr as dump_kernel_instr arm64/mm: Drop [PTE|PMD]_TYPE_FAULT arm64: Implement panic_smp_self_stop() arm64: Improve parking of stopped CPUs arm64: Expose FRINT capabilities to userspace arm64: Expose ARMv8.5 CondM capability to userspace arm64: defconfig: enable CONFIG_RANDOMIZE_BASE arm64: ARM64_MODULES_PLTS must depend on MODULES arm64: bpf: do not allocate executable memory arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP arm64: module: create module allocations without exec permissions arm64: Allow user selection of ARM64_MODULE_PLTS acpi/arm64: ignore 5.1 FADTs that are reported as 5.0 arm64: Allow selecting Pseudo-NMI again ...
2019-06-27arm_pmu: acpi: spe: Add initial MADT/SPE probingJeremy Linton1-0/+2
ACPI 6.3 adds additional fields to the MADT GICC structure to describe SPE PPI's. We pick these out of the cached reference to the madt_gicc structure similarly to the core PMU code. We then create a platform device referring to the IRQ and let the user/module loader decide whether to load the SPE driver. Tested-by: Hanjun Guo <hanjun.guo@linaro.org> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Will Deacon <will@kernel.org>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner1-5/+1
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-11-21arm64: perf: Add support for Armv8.1 PMCEID register formatWill Deacon1-1/+3
Armv8.1 allocated the upper 32-bits of the PMCEID registers to describe the common architectural and microarchitecture events beginning at 0x4000. Add support for these registers to our probing code, so that we can advertise the SPE events when they are supported by the CPU. Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-10-12arm64: perf: Reject stand-alone CHAIN events for PMUv3Will Deacon1-0/+1
It doesn't make sense for a perf event to be configured as a CHAIN event in isolation, so extend the arm_pmu structure with a ->filter_match() function to allow the backend PMU implementation to reject CHAIN events early. Cc: <stable@vger.kernel.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10arm_pmu: Add support for 64bit event countersSuzuki K Poulose1-0/+6
Each PMU has a set of 32bit event counters. But in some special cases, the events could be counted using counters which are effectively 64bit wide. e.g, Arm V8 PMUv3 has a 64 bit cycle counter which can count only the CPU cycles. Also, the PMU can chain the event counters to effectively count as a 64bit counter. Add support for tracking the events that uses 64bit counters. This only affects the periods set for each counter in the core driver. Cc: Will Deacon <will.deacon@arm.com> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10arm_pmu: Change API to support 64bit counter valuesSuzuki K Poulose1-2/+2
Convert the {read/write}_counter APIs to handle 64bit values to enable supporting chained event counters. The backends still use 32bit values and we pass them 32bit values only. So in effect there are no functional changes. Cc: Will Deacon <will.deacon@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-07-10arm_pmu: Clean up maximum period handlingSuzuki K Poulose1-1/+0
Each PMU defines their max_period of the counter as the maximum value that can be counted. Since all the PMU backends support 32bit counters by default, let us remove the redundant field. No functional changes. Cc: Will Deacon <will.deacon@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-05-21arm_pmu: simplify arm_pmu::handle_irqMark Rutland1-1/+1
The arm_pmu::handle_irq() callback has the same prototype as a generic IRQ handler, taking the IRQ number and a void pointer argument which it must convert to an arm_pmu pointer. This means that all arm_pmu::handle_irq() take an IRQ number they never use, and all must explicitly cast the void pointer to an arm_pmu pointer. Instead, let's change arm_pmu::handle_irq to take an arm_pmu pointer, allowing these casts to be removed. The redundant IRQ number parameter is also removed. Suggested-by: Hoeun Ryu <hoeun.ryu@lge.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20arm_pmu: acpi: request IRQs up-frontMark Rutland1-2/+3
We can't request IRQs in atomic context, so for ACPI systems we'll have to request them up-front, and later associate them with CPUs. This patch reorganises the arm_pmu code to do so. As we no longer have the arm_pmu structure at probe time, a number of prototypes need to be adjusted, requiring changes to the common arm_pmu code and arm_pmu platform code. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20arm_pmu: note IRQs and PMUs per-cpuMark Rutland1-1/+0
To support ACPI systems, we need to request IRQs before we know the associated PMU, and thus we need some percpu variable that the IRQ handler can find the PMU from. As we're going to request IRQs without the PMU, we can't rely on the arm_pmu::active_irqs mask, and similarly need to track requested IRQs with a percpu variable. Signed-off-by: Mark Rutland <mark.rutland@arm.com> [will: made armpmu_count_irq_users static] Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20arm_pmu: add armpmu_alloc_atomic()Mark Rutland1-0/+1
In ACPI systems, we don't know the makeup of CPUs until we hotplug them on, and thus have to allocate the PMU datastructures at hotplug time. Thus, we must use GFP_ATOMIC allocations. Let's add an armpmu_alloc_atomic() that we can use in this case. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20arm_pmu: fold platform helpers into platform codeMark Rutland1-2/+0
The armpmu_{request,free}_irqs() helpers are only used by arm_pmu_platform.c, so let's fold them in and make them static. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2018-02-20arm_pmu: kill arm_pmu_platdataMark Rutland1-17/+0
Now that we have no platforms passing platform data to the arm_pmu code, we can get rid of the platdata and associated hooks, paving the way for rework of our IRQ handling. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-07-27drivers/perf: arm_pmu: Request PMU SPIs with IRQF_PER_CPUWill Deacon1-0/+4
Since the PMU register interface is banked per CPU, CPU PMU interrrupts cannot be handled by a CPU other than the one with the PMU asserting the interrupt. This means that migrating PMU SPIs, as we do during a CPU hotplug operation doesn't make any sense and can lead to the IRQ being disabled entirely if we route a spurious IRQ to the new affinity target. This has been observed in practice on AMD Seattle, where CPUs on the non-boot cluster appear to take a spurious PMU IRQ when coming online, which is routed to CPU0 where it cannot be handled. This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their affinity prior to requesting them, ensuring that they cannot be migrated during hotplug events. This interacts badly with the DB8500 erratum workaround that ping-pongs the interrupt affinity from the handler, so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags to be overridden in the platdata. Fixes: 3cf7ee98b848 ("drivers/perf: arm_pmu: move irq request/free into probe") Cc: Mark Rutland <mark.rutland@arm.com> Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11drivers/perf: arm_pmu: add ACPI frameworkMark Rutland1-0/+11
This patch adds framework code to handle parsing PMU data out of the MADT, sanity checking this, and managing the association of CPUs (and their interrupts) with appropriate logical PMUs. For the time being, we expect that only one PMU driver (PMUv3) will make use of this, and we simply pass in a single probe function. This is based on an earlier patch from Jeremy Linton. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Jeremy Linton <jeremy.linton@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11drivers/perf: arm_pmu: split out platform device probe logicMark Rutland1-0/+7
Now that we've split the pdev and DT probing logic from the runtime management, let's move the former into its own file. We gain a few lines due to the copyright header and includes, but this should keep the logic clearly separated, and paves the way for adding ACPI support in a similar fashion. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Jeremy Linton <jeremy.linton@arm.com> [will: rename nr_irqs to avoid conflict with global variable] Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-04-11drivers/perf: arm_pmu: define armpmu_init_fnMark Rutland1-1/+3
We expect an ARM PMU's init function to have a particular prototype, which we open-code in a few places. This is less than ideal, considering that we cast a void value to this type in one location, and a mismatch could easily be missed. Add a typedef so that we can ensure this is consistent. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Jeremy Linton <jeremy.linton@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-03-31drivers/perf: arm_pmu: split irq request from enableMark Rutland1-4/+0
For historical reasons, we lazily request and free interrupts in the arm pmu driver. This requires us to refcount use of the pmu (by way of counting the active events) in order to request/free interrupts at the correct times, which complicates the driver somewhat. The existing logic is flawed, as it only considers currently online CPUs when requesting, freeing, or managing the affinity of interrupts. Intervening hotplug events can result in erroneous IRQ affinity, online CPUs for which interrupts have not been requested, or offline CPUs whose interrupts are still requested. To fix this, this patch splits the requesting of interrupts from any per-cpu management (i.e. per-cpu enable/disable, and configuration of cpu affinity). We now request all interrupts up-front at probe time (and never free them, since we never unregister PMUs). The management of affinity, and per-cpu enable/disable now happens in our cpu hotplug callback, ensuring it occurs consistently. This means that we must now invoke the CPU hotplug callback at boot time in order to configure IRQs, and since the callback also resets the PMU hardware, we can remove the duplicate reset in the probe path. This rework renders our event refcounting unnecessary, so this is removed. Signed-off-by: Mark Rutland <mark.rutland@arm.com> [will: make armpmu_get_cpu_irq static] Signed-off-by: Will Deacon <will.deacon@arm.com>
2017-03-31drivers/perf: arm_pmu: manage interrupts per-cpuMark Rutland1-1/+2
When requesting or freeing interrupts, we use platform_get_irq() to find relevant irqs, backing this up with additional information in an optional irq_affinity table. This means that our irq request and free paths are tied to a platform_device, and our request path must jump through a number of hoops in order to determine the required affinity of each interrupt. Given that the affinity must be static, we can compute the affinity once up-front at probe time, simplifying the irq request and free paths. By recording interrupts in a per-cpu data structure, we simplify a few paths, and permit a subsequent rework of the request and free paths. Signed-off-by: Mark Rutland <mark.rutland@arm.com> [will: rename local nr_irqs variable to avoid conflict with global] Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-10-04Merge branch 'smp-hotplug-for-linus' of ↵Linus Torvalds1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull CPU hotplug updates from Thomas Gleixner: "Yet another batch of cpu hotplug core updates and conversions: - Provide core infrastructure for multi instance drivers so the drivers do not have to keep custom lists. - Convert custom lists to the new infrastructure. The block-mq custom list conversion comes through the block tree and makes the diffstat tip over to more lines removed than added. - Handle unbalanced hotplug enable/disable calls more gracefully. - Remove the obsolete CPU_STARTING/DYING notifier support. - Convert another batch of notifier users. The relayfs changes which conflicted with the conversion have been shipped to me by Andrew. The remaining lot is targeted for 4.10 so that we finally can remove the rest of the notifiers" * 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits) cpufreq: Fix up conversion to hotplug state machine blk/mq: Reserve hotplug states for block multiqueue x86/apic/uv: Convert to hotplug state machine s390/mm/pfault: Convert to hotplug state machine mips/loongson/smp: Convert to hotplug state machine mips/octeon/smp: Convert to hotplug state machine fault-injection/cpu: Convert to hotplug state machine padata: Convert to hotplug state machine cpufreq: Convert to hotplug state machine ACPI/processor: Convert to hotplug state machine virtio scsi: Convert to hotplug state machine oprofile/timer: Convert to hotplug state machine block/softirq: Convert to hotplug state machine lib/irq_poll: Convert to hotplug state machine x86/microcode: Convert to hotplug state machine sh/SH-X3 SMP: Convert to hotplug state machine ia64/mca: Convert to hotplug state machine ARM/OMAP/wakeupgen: Convert to hotplug state machine ARM/shmobile: Convert to hotplug state machine arm64/FP/SIMD: Convert to hotplug state machine ...
2016-09-16arm64: pmu: Hoist pmu platform device nameJeremy Linton1-0/+2
Move the PMU name into a common header file so it may be referenced by other users. Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-09drivers/perf: arm_pmu: expose a cpumask in sysfsMark Rutland1-0/+1
In systems with heterogeneous CPUs, there are multiple logical CPU PMUs, each of which covers a subset of CPUs in the system. In some cases userspace needs to know which CPUs a given logical PMU covers, so we'd like to expose a cpumask under sysfs, similar to what is done for uncore PMUs. Unfortunately, prior to commit 00e727bb389359c8 ("perf stat: Balance opening and reading events"), perf stat only correctly handled a cpumask holding a single CPU, and only when profiling in system-wide mode. In other cases, the presence of a cpumask file could cause perf stat to behave erratically. Thus, exposing a cpumask file would break older perf binaries in cases where they would otherwise work. To avoid this issue while still providing userspace with the information it needs, this patch exposes a differently-named file (cpus) under sysfs. New tools can look for this and operate correctly, while older tools will not be adversely affected by its presence. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-09drivers/perf: arm_pmu: add common attr group fieldsMark Rutland1-1/+9
In preparation for adding common attribute groups, add an array of attribute group pointers to arm_pmu, which will be used if the backend hasn't already set pmu::attr_groups. Subsequent patches will move backends over to using these, before adding common fields. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-09-02arm/perf: Use multi instance instead of custom listSebastian Andrzej Siewior1-1/+1
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160817171420.sdwk2qivxunzryz4@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2016-07-20arm/perf: Fix hotplug state machine conversionSebastian Andrzej Siewior1-0/+1
Mark Rutland pointed out that this commit is incomplete: 7d88eb695a1f ("arm/perf: Convert to hotplug state machine") The problem is that: > We may have multiple PMUs (e.g. two in big.LITTLE systems), and > __oprofile_cpu_pmu only contains one of these. So this conversion is not > correct. > > We were relying on the notifier list implicitly containing a list of > those PMUs. It seems like we need an explicit list here. > > We keep __oprofile_cpu_pmu around for legacy 32-bit users of OProfile > (on non-hetereogeneous systems), and that's all that the variable should > be used for. Introduce arm_pmu_list to correctly handle multiple PMUs in the system. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Mark Rutland <mark.rutland@arm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-tip-commits@vger.kernel.org Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160719111733.GA22911@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-07-15arm/perf: Convert to hotplug state machineThomas Gleixner1-1/+0
Straight forward conversion w/o bells and whistles. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160713153335.794097159@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
2016-04-25arm64/perf: Filter common events based on PMCEIDn_EL0Ashok Kumar1-0/+2
The complete common architectural and micro-architectural event number structure is filtered based on PMCEIDn_EL0 and exposed to /sys using is_visibile function pointer in events attribute_group. To filter the events in is_visible function, pmceid based bitmap is stored in arm_pmu structure and the id field from perf_pmu_events_attr is used to check against the bitmap. The function which derives event bitmap from PMCEIDn_EL0 is executed in the cpus, which has the pmu being initialized, for heterogeneous pmu support. Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Ashok Kumar <ashoks@broadcom.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-02-26drivers/perf: arm_pmu: implement CPU_PM notifierLorenzo Pieralisi1-0/+1
When a CPU is suspended (either through suspend-to-RAM or CPUidle), its PMU registers content can be lost, which means that counters registers values that were initialized on power down entry have to be reprogrammed on power-up to make sure the counters set-up is preserved (ie on power-up registers take the reset values on Cold or Warm reset, which can be architecturally UNKNOWN). To guarantee seamless profiling conditions across a core power down this patch adds a CPU PM notifier to ARM pmus, that upon CPU PM entry/exit from low-power states saves/restores the pmu registers set-up (by using the ARM perf API), so that the power-down/up cycle does not affect the perf behaviour (apart from a black-out period between power-up/down CPU PM notifications that is unavoidable). Cc: Will Deacon <will.deacon@arm.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org> Acked-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2016-01-25ARM: perf: Set ARMv7 SDER SUNIDEN bitMartin Fuzzey1-0/+1
ARMv7 counters other than the CPU cycle counter only work if the Secure Debug Enable Register (SDER) SUNIDEN bit is set. Since access to the SDER is only possible in secure state, it will only be done if the device tree property "secure-reg-access" is set. Without this: Performance counter stats for 'sleep 1': 14606094 cycles # 0.000 GHz 0 instructions # 0.00 insns per cycle After applying: Performance counter stats for 'sleep 1': 5843809 cycles 2566484 instructions # 0.44 insns per cycle 1.020144000 seconds time elapsed Some platforms (eg i.MX53) may also need additional platform specific setup. Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com> Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com> Signed-off-by: George G. Davis <george_davis@mentor.com> [will: add warning if property is found on arm64] Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-11-16drivers/perf: kill armpmu_registerMark Rutland1-2/+0
Nothing outside of drivers/perf/arm_pmu.c should call armpmu_register any more, so it no longer needs to be in include/linux/perf/arm_pmu.h. Additionally, by folding it in to arm_pmu_device_probe we can allow drivers to override struct pmu fields without getting blatted by the armpmu code. This patch folds armpmu_register into arm_pmu_device_probe. The logging to the console is moved to after the PMU is successfully registered with the core perf code. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Suggested-by: Will Deacon <will.deacon@arm.com> Cc: Drew Richardson <drew.richardson@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-07-31arm: perf: factor arm_pmu core out to driversMark Rutland1-0/+154
To enable sharing of the arm_pmu code with arm64, this patch factors it out to drivers/perf/. A new drivers/perf directory is added for performance monitor drivers to live under. MAINTAINERS is updated accordingly. Files added previously without a corresponsing MAINTAINERS update (perf_regs.c, perf_callchain.c, and perf_event.h) are also added. Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Russell King <linux@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> [will: augmented Kconfig help slightly] Signed-off-by: Will Deacon <will.deacon@arm.com>