| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The skb is handed off to netif_rx() which may free it.
Found by Smatch.
OpenBMC-Staging-Count: 1
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit 06bf1ce69d55729dc132d423d626398254fedc58)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Provides MCTP network transport over an I2C bus, as specified in
DMTF DSP0237. All messages between nodes are sent as SMBus Block Writes.
Each I2C bus to be used for MCTP is flagged in devicetree by a
'mctp-controller' property on the bus node. Each flagged bus gets a
mctpi2cX net device created based on the bus number. A
'mctp-i2c-controller' I2C client needs to be added under the adapter. In
an I2C mux situation the mctp-i2c-controller node must be attached only
to the root I2C bus. The I2C client will handle incoming I2C slave block
write data for subordinate busses as well as its own bus.
In configurations without devicetree a driver instance can be attached
to a bus using the I2C slave new_device mechanism.
The MCTP core will hold/release the MCTP I2C device while responses
are pending (a 6 second timeout or once a socket is closed, response
received etc). While held the MCTP I2C driver will lock the I2C bus so
that the correct I2C mux remains selected while responses are received.
(Ideally we would just lock the mux to keep the current bus selected for
the response rather than a full I2C bus lock, but that isn't exposed in
the I2C mux API)
OpenBMC-Staging-Count: 1
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Wolfram Sang <wsa@kernel.org> # I2C transport parts
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit f5b8abf9fc3dacd7529d363e26fe8230935d65f8)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Jiri assures me that a ldisc->open with tty->disc_data set should never
happen, so this check doesn't do anything.
OpenBMC-Staging-Count: 1
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit d1c99f365a1f51f9c7e76ea3c52605cf740b3251)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The current serial driver requires a maximum MTU of 68, and it doesn't
make sense to set a MTU below the MCTP-required baseline (of 68) either.
This change sets the min_mtu & max_mtu of the mctp netdev, essentially
disallowing changes. By using these instead of a ndo_change_mtu op, we
get the netlink extacks reported too.
OpenBMC-Staging-Count: 1
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit d154cd078ac2d24374e872f3224bf44894867b0a)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
We want to ensure that the tx work has finished before returning from
the ldisc close op, so do a synchronous cancel.
OpenBMC-Staging-Count: 1
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(cherry picked from commit 7bd9890f3d74e96f0e1a898f68decfc711de3001)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This change adds a MCTP Serial transport binding, as defined by DMTF
specificiation DSP0253 - "MCTP Serial Transport Binding". This is
implemented as a new serial line discipline, and can be attached to
arbitrary tty devices.
From the Kconfig description:
This driver provides an MCTP-over-serial interface, through a
serial line-discipline, as defined by DMTF specification "DSP0253 -
MCTP Serial Transport Binding". By attaching the ldisc to a serial
device, we get a new net device to transport MCTP packets.
This allows communication with external MCTP endpoints which use
serial as their transport. It can also be used as an easy way to
provide MCTP connectivity between virtual machines, by forwarding
data between simple virtual serial devices.
Say y here if you need to connect to MCTP endpoints over serial. To
compile as a module, use m; the module will be called mctp-serial.
Once the N_MCTP line discipline is set [using ioctl(TCIOSETD)], we get a
new netdev suitable for MCTP communication.
The 'mctp' utility[1] provides a simple wrapper for this ioctl, using
'link serial <device>':
# mctp link serial /dev/ttyS0 &
# mctp link
dev lo index 1 address 0x00:00:00:00:00:00 net 1 mtu 65536 up
dev mctpserial0 index 5 address 0x(no-addr) net 1 mtu 68 down
[1]: https://github.com/CodeConstruct/mctp
OpenBMC-Staging-Count: 1
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit a0c2ccd9b5ad0a9e838158404e041b5a8ff762dd)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Added pmbus driver for the new device Renesas raa229126
voltage regulator.
Signed-off-by: Zhikui Ren <zhikui.ren@intel.com>
|
|
commit 95932ab2ea07b79cdb33121e2f40ccda9e6a73b5 upstream.
Commit e2ae38cf3d91 ("vhost: fix hung thread due to erroneous iotlb
entries") tries to reject the IOTLB message whose size is zero. But
the size is not necessarily meaningful, one example is the batching
hint, so the commit breaks that.
Fixing this be reject zero size message only if the message is used to
update/invalidate the IOTLB.
Fixes: e2ae38cf3d91 ("vhost: fix hung thread due to erroneous iotlb entries")
Reported-by: Eli Cohen <elic@nvidia.com>
Cc: Anirudh Rayabharam <mail@anirudhrb.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220310075211.4801-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2566a89b9e163b2fcd104d6005e0149f197b8a48 which is
commit a2614140dc0f467a83aa3bb4b6ee2d6480a76202 upstream.
The above change depends on upstream commit 0faf890fc519 ("net: dsa:
drop rtnl_lock from dsa_slave_switchdev_event_work"), which is not
present in linux-5.15.y. Without that change, waiting for the switchdev
workqueue causes deadlocks on the rtnl_mutex.
Backporting the dependency commit isn't trivial/desirable, since it
requires that the following dependencies of the dependency are also
backported:
df405910ab9f net: dsa: sja1105: wait for dynamic config command completion on writes too
eb016afd83a9 net: dsa: sja1105: serialize access to the dynamic config interface
2468346c5677 net: mscc: ocelot: serialize access to the MAC table
f7eb4a1c0864 net: dsa: b53: serialize access to the ARL table
cf231b436f7c net: dsa: lantiq_gswip: serialize access to the PCE registers
338a3a4745aa net: dsa: introduce locking for the address lists on CPU and DSA ports
and then this bugfix on top:
8940e6b669ca ("net: dsa: avoid call to __dev_set_promiscuity() while rtnl_mutex isn't held")
Reported-by: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b81e0c2372e65e5627864ba034433b64b2fc73f5 upstream.
Drop various include not actually used in genhd.h itself, and
move the remaning includes closer together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>a
Reported-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
[ resolves MIPS build failure by luck, root cause needs to be fixed in
Linus's tree properly, but this is needed for now to fix the build - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4e6f55120c7eccf6f9323bb681632e23cbcb3f3c upstream.
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb3975a8c2366e3883337e252bb0eee5)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3755d35ee1d2454b20b8a1e20d790e56201678a4 upstream.
As reported in [1], DRM_PANEL_EDP depends on DRM_DP_HELPER. Select
the option to fix the build failure. The error message is shown
below.
arm-linux-gnueabihf-ld: drivers/gpu/drm/panel/panel-edp.o: in function
`panel_edp_probe': panel-edp.c:(.text+0xb74): undefined reference to
`drm_panel_dp_aux_backlight'
make[1]: *** [/builds/linux/Makefile:1222: vmlinux] Error 1
The issue has been reported before, when DisplayPort helpers were
hidden behind the option CONFIG_DRM_KMS_HELPER. [2]
v2:
* fix and expand commit description (Arnd)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 9d6366e743f3 ("drm: fb_helper: improve CONFIG_FB dependency")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/dri-devel/CA+G9fYvN0NyaVkRQmA1O6rX7H8PPaZrUAD7=RDy33QY9rUU-9g@mail.gmail.com/ # [1]
Link: https://lore.kernel.org/all/20211117062704.14671-1-rdunlap@infradead.org/ # [2]
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220203093922.20754-1-tzimmermann@suse.de
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 39bab83b119faac4bf7f07173a42ed35be95147e upstream.
Only prio 1 is supported for nic mode when there is no ignore flow level
support in firmware. But for switchdev mode, which supports fixed number
of statically pre-allocated prios, this restriction is not relevant so
it can be relaxed.
Fixes: d671e109bd85 ("net/mlx5: Fix tc max supported prio for nic mode")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fa59ede95195f267101a1b8916992cf3f245cdb upstream.
The feature negotiation was designed in a way that
makes it possible for devices to know which config
fields will be accessed by drivers.
This is broken since commit 404123c2db79 ("virtio: allow drivers to
validate features") with fallout in at least block and net. We have a
partial work-around in commit 2f9a174f918e ("virtio: write back
F_VERSION_1 before validate") which at least lets devices find out which
format should config space have, but this is a partial fix: guests
should not access config space without acknowledging features since
otherwise we'll never be able to change the config space format.
To fix, split finalize_features from virtio_finalize_features and
call finalize_features with all feature bits before validation,
and then - if validation changed any bits - once again after.
Since virtio_finalize_features no longer writes out features
rename it to virtio_features_ok - since that is what it does:
checks that features are ok with the device.
As a side effect, this also reduces the amount of hypervisor accesses -
we now only acknowledge features once unless we are clearing any
features when validating (which is uncommon).
IRC I think that this was more or less always the intent in the spec but
unfortunately the way the spec is worded does not say this explicitly, I
plan to address this at the spec level, too.
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 404123c2db79 ("virtio: allow drivers to validate features")
Fixes: 2f9a174f918e ("virtio: write back F_VERSION_1 before validate")
Cc: "Halil Pasic" <pasic@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 838d6d3461db0fdbf33fc5f8a69c27b50b4a46da upstream.
virtio_finalize_features is only used internally within virtio.
No reason to export it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0d2f15362f02444c5d7ffd5a5eb03e4aa54b685 upstream.
Currently meson_mmc_post_req() is called in meson_mmc_request() right
after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request
is actually finished.
To fix, don't call meson_mmc_post_req() until meson_mmc_request_done().
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0bf476fc3624e3a72af4ba7340d430a91c18cd67 upstream.
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done")
Cc: stable@vger.kernel.org
Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fc7f750dc9d102c1ed7bbe4591f991e770c99033 upstream.
The netif_rx_ni() function frees the skb so we can't dereference it to
save the skb->len.
Fixes: 61e121047645 ("staging: gdm7240: adding LTE USB driver")
Cc: stable <stable@vger.kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220228074331.GA13685@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f4347081be32e67b0873827e0138ab0fdaaf450 upstream.
Commit 54659ca026e5 ("staging: rtl8723bs: remove possible deadlock when
disconnect (v2)") split the locking of pxmitpriv->lock vs sleep_q/lock
into 2 locks in attempt to fix a lockdep reported issue with the locking
order of the sta_hash_lock vs pxmitpriv->lock.
But in the end this turned out to not fully solve the sta_hash_lock issue
so commit a7ac783c338b ("staging: rtl8723bs: remove a second possible
deadlock") was added to fix this in another way.
The original fix was kept as it was still seen as a good thing to have,
but now it turns out that it creates a deadlock in access-point mode:
[Feb20 23:47] ======================================================
[ +0.074085] WARNING: possible circular locking dependency detected
[ +0.074077] 5.16.0-1-amd64 #1 Tainted: G C E
[ +0.064710] ------------------------------------------------------
[ +0.074075] ksoftirqd/3/29 is trying to acquire lock:
[ +0.060542] ffffb8b30062ab00 (&pxmitpriv->lock){+.-.}-{2:2}, at: rtw_xmit_classifier+0x8a/0x140 [r8723bs]
[ +0.114921]
but task is already holding lock:
[ +0.069908] ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
[ +0.116976]
which lock already depends on the new lock.
[ +0.098037]
the existing dependency chain (in reverse order) is:
[ +0.089704]
-> #1 (&psta->sleep_q.lock){+.-.}-{2:2}:
[ +0.077232] _raw_spin_lock_bh+0x34/0x40
[ +0.053261] xmitframe_enqueue_for_sleeping_sta+0xc1/0x2f0 [r8723bs]
[ +0.082572] rtw_xmit+0x58b/0x940 [r8723bs]
[ +0.056528] _rtw_xmit_entry+0xba/0x350 [r8723bs]
[ +0.062755] dev_hard_start_xmit+0xf1/0x320
[ +0.056381] sch_direct_xmit+0x9e/0x360
[ +0.052212] __dev_queue_xmit+0xce4/0x1080
[ +0.055334] ip6_finish_output2+0x18f/0x6e0
[ +0.056378] ndisc_send_skb+0x2c8/0x870
[ +0.052209] ndisc_send_ns+0xd3/0x210
[ +0.050130] addrconf_dad_work+0x3df/0x5a0
[ +0.055338] process_one_work+0x274/0x5a0
[ +0.054296] worker_thread+0x52/0x3b0
[ +0.050124] kthread+0x16c/0x1a0
[ +0.044925] ret_from_fork+0x1f/0x30
[ +0.049092]
-> #0 (&pxmitpriv->lock){+.-.}-{2:2}:
[ +0.074101] __lock_acquire+0x10f5/0x1d80
[ +0.054298] lock_acquire+0xd7/0x300
[ +0.049088] _raw_spin_lock_bh+0x34/0x40
[ +0.053248] rtw_xmit_classifier+0x8a/0x140 [r8723bs]
[ +0.066949] rtw_xmitframe_enqueue+0xa/0x20 [r8723bs]
[ +0.066946] rtl8723bs_hal_xmitframe_enqueue+0x14/0x50 [r8723bs]
[ +0.078386] wakeup_sta_to_xmit+0xa6/0x300 [r8723bs]
[ +0.065903] rtw_recv_entry+0xe36/0x1160 [r8723bs]
[ +0.063809] rtl8723bs_recv_tasklet+0x349/0x6c0 [r8723bs]
[ +0.071093] tasklet_action_common.constprop.0+0xe5/0x110
[ +0.070966] __do_softirq+0x16f/0x50a
[ +0.050134] __irq_exit_rcu+0xeb/0x140
[ +0.051172] irq_exit_rcu+0xa/0x20
[ +0.047006] common_interrupt+0xb8/0xd0
[ +0.052214] asm_common_interrupt+0x1e/0x40
[ +0.056381] finish_task_switch.isra.0+0x100/0x3a0
[ +0.063670] __schedule+0x3ad/0xd20
[ +0.048047] schedule+0x4e/0xc0
[ +0.043880] smpboot_thread_fn+0xc4/0x220
[ +0.054298] kthread+0x16c/0x1a0
[ +0.044922] ret_from_fork+0x1f/0x30
[ +0.049088]
other info that might help us debug this:
[ +0.095950] Possible unsafe locking scenario:
[ +0.070952] CPU0 CPU1
[ +0.054282] ---- ----
[ +0.054285] lock(&psta->sleep_q.lock);
[ +0.047004] lock(&pxmitpriv->lock);
[ +0.074082] lock(&psta->sleep_q.lock);
[ +0.077209] lock(&pxmitpriv->lock);
[ +0.043873]
*** DEADLOCK ***
[ +0.070950] 1 lock held by ksoftirqd/3/29:
[ +0.049082] #0: ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
Analysis shows that in hindsight the splitting of the lock was not
a good idea, so revert this to fix the access-point mode deadlock.
Note this is a straight-forward revert done with git revert, the commented
out "/* spin_lock_bh(&psta_bmc->sleep_q.lock); */" lines were part of the
code before the reverted changes.
Fixes: 54659ca026e5 ("staging: rtl8723bs: remove possible deadlock when disconnect (v2)")
Cc: stable <stable@vger.kernel.org>
Cc: Fabio Aiuto <fabioaiuto83@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215542
Link: https://lore.kernel.org/r/20220302101637.26542-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e8240addd0a3919e0fd7436416afe9aa6429c484 ]
This reverts commit 2afeec08ab5c86ae21952151f726bfe184f6b23d.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f4558ae91870692ce7f509c31c9d6ee721d8cdc ]
This reverts commit 1f2565780e9b7218cf92c7630130e82dcc0fe9c2.
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/20220222001817.2264967-1-marmarek@invisiblethingslab.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2b993302f40c4eb714ecf896dd9e1c5be7d4cd7 ]
vkms leverages common amdgpu framebuffer creation, and
also as it does not support FB modifier, there is no need
to check tiling flags when initing framebuffer when virtual
display is enabled.
This can fix below calltrace:
amdgpu 0000:00:08.0: GFX9+ requires FB check based on format modifier
WARNING: CPU: 0 PID: 1023 at drivers/gpu/drm/amd/amdgpu/amdgpu_display.c:1150 amdgpu_display_framebuffer_init+0x8e7/0xb40 [amdgpu]
v2: check adev->enable_virtual_display instead as vkms can be
enabled in bare metal as well.
Signed-off-by: Leslie Shi <Yuliang.Shi@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ae42f9288846353982e2eab181fb41e7fd8bf60f ]
We are racing the registering of .to_irq when probing the
i2c driver. This results in random failure of touchscreen
devices.
Following explains the race condition better.
[gpio driver] gpio driver registers gpio chip
[gpio consumer] gpio is acquired
[gpio consumer] gpiod_to_irq() fails with -ENXIO
[gpio driver] gpio driver registers irqchip
gpiod_to_irq works at this point, but -ENXIO is fatal
We could see the following errors in dmesg logs when gc->to_irq is NULL
[2.101857] i2c_hid i2c-FTS3528:00: HID over i2c has not been provided an Int IRQ
[2.101953] i2c_hid: probe of i2c-FTS3528:00 failed with error -22
To avoid this situation, defer probing until to_irq is registered.
Returning -EPROBE_DEFER would be the first step towards avoiding
the failure of devices due to the race in registration of .to_irq.
Final solution to this issue would be to avoid using gc irq members
until they are fully initialized.
This issue has been reported many times in past and people have been
using workarounds like changing the pinctrl_amd to built-in instead
of loading it as a module or by adding a softdep for pinctrl_amd into
the config file.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209413
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3f1271b54edcc692da5a3663f2aa2a64781f9bc3 ]
There are enough VBIOS escapes without the proper workaround that some
users still hit this. Microsoft never productized ATS on Windows so OEM
platforms that were Windows-only didn't always validate ATS.
The advantages of ATS are not worth it compared to the potential
instabilities on harvested boards. Disable ATS on all Navi10 and Navi14
boards.
Symptoms include:
amdgpu 0000:07:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0007 address=0xffffc02000 flags=0x0000]
AMD-Vi: Event logged [IO_PAGE_FAULT device=07:00.0 domain=0x0007 address=0xffffc02000 flags=0x0000]
[drm:amdgpu_job_timedout [amdgpu]] *ERROR* ring sdma0 timeout, signaled seq=6047, emitted seq=6049
amdgpu 0000:07:00.0: amdgpu: GPU reset begin!
amdgpu 0000:07:00.0: amdgpu: GPU reset succeeded, trying to resume
amdgpu 0000:07:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring sdma0 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <sdma_v4_0> failed -110
amdgpu 0000:07:00.0: amdgpu: GPU reset(1) failed
Related commits:
e8946a53e2a6 ("PCI: Mark AMD Navi14 GPU ATS as broken")
a2da5d8cc0b0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
45beb31d3afb ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
5e89cd303e3a ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
d28ca864c493 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
9b44b0b09dec ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: add symptoms and related commits]
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1760
Link: https://lore.kernel.org/r/20220222160801.841643-1-alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 35f165f08950a876f1b95a61d79c93678fba2fd6 ]
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Signed-off-by: Vikash Chandola <vikash.chandola@linux.intel.com>
Link: https://lore.kernel.org/r/20220222131253.2426834-1-vikash.chandola@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e40945ab7c7f966d0c37b7bd7b0596497dfe228d ]
On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 80808768e41324d2e23de89972b5406c1020e6e4 ]
After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9382df0a98aad5bbcd4d634790305a1d786ad224 ]
Get num-cs u32 from dts of_node property rather than u16.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-2-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6f66db29e2415cbe8759c48584f9cae19b3c2651 ]
It appears that last minute change moved ACPI ID of Alder Lake-M
to the INTC1055, which is already in the driver.
This ID on the other hand will be used elsewhere.
This reverts commit 258435a1c8187f559549e515d2f77fa0b57bcd27.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 038438a25c45d5ac996e95a22fa9e76ff3d1f8c7 ]
This patch adds the necessary PCI ID for Intel Raptor Lake-S
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220214141948.18637-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2c87c6f9fbddc5b84d67b2fa3f432fcac6d99d93 ]
Sometimes the link comes up but no data flows. This patch fixes
this behavior. It's not clear what's the root cause of the issue.
According to the tests one other link-up issue remains.
In very rare cases the link isn't even reported as up.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Tested-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/e3473452-a1f9-efcf-5fdd-02b6f44c3fcd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00b022f8f876a3a036b0df7f971001bef6398605 ]
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 37c9d66c95564c85a001d8a035354f0220a1e1c3 ]
MISR1 was cleared twice but the original author intention was probably
to clear MISR1 & MISR2 to completely disable interrupts. Fix it to
clear MISR2.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220309142228.761153-1-clement.leger@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2ac5b58e645c66932438bb021cb5b52097ce70b0 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 7349a74ea75c ("net: ethernet: gianfar_ethtool: get phc index through drvdata")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220310015313.14938-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 03fe003547975680fdb9ff5ab0e41cb68276c4f2 ]
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
Fixes: 9c6686322d74 ("gpio: add Technologic I2C-FPGA gpio support")
Signed-off-by: Mark Featherston <mark@embeddedTS.com>
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f80cfe2f26581f188429c12bd937eb905ad3ac7b ]
Syzbot reported UAF in port100_send_complete(). The root case is in
missing usb_kill_urb() calls on error handling path of ->probe function.
port100_send_complete() accesses devm allocated memory which will be
freed on probe failure. We should kill this urbs before returning an
error from probe function to prevent reported use-after-free
Fail log:
BUG: KASAN: use-after-free in port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
Read of size 1 at addr ffff88801bb59540 by task ksoftirqd/2/26
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
__usb_hcd_giveback_urb+0x2b0/0x5c0 drivers/usb/core/hcd.c:1670
...
Allocated by task 1255:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
kasan_set_track mm/kasan/common.c:45 [inline]
set_alloc_info mm/kasan/common.c:436 [inline]
____kasan_kmalloc mm/kasan/common.c:515 [inline]
____kasan_kmalloc mm/kasan/common.c:474 [inline]
__kasan_kmalloc+0xa6/0xd0 mm/kasan/common.c:524
alloc_dr drivers/base/devres.c:116 [inline]
devm_kmalloc+0x96/0x1d0 drivers/base/devres.c:823
devm_kzalloc include/linux/device.h:209 [inline]
port100_probe+0x8a/0x1320 drivers/nfc/port100.c:1502
Freed by task 1255:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
kasan_set_track+0x21/0x30 mm/kasan/common.c:45
kasan_set_free_info+0x20/0x30 mm/kasan/generic.c:370
____kasan_slab_free mm/kasan/common.c:366 [inline]
____kasan_slab_free+0xff/0x140 mm/kasan/common.c:328
kasan_slab_free include/linux/kasan.h:236 [inline]
__cache_free mm/slab.c:3437 [inline]
kfree+0xf8/0x2b0 mm/slab.c:3794
release_nodes+0x112/0x1a0 drivers/base/devres.c:501
devres_release_all+0x114/0x190 drivers/base/devres.c:530
really_probe+0x626/0xcc0 drivers/base/dd.c:670
Reported-and-tested-by: syzbot+16bcb127fb73baeecb14@syzkaller.appspotmail.com
Fixes: 0347a6ab300a ("NFC: port100: Commands mechanism implementation")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220308185007.6987-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad11c4f1d8fd1f03639460e425a36f7fd0ea83f5 ]
There could be multiple multipath entries but changing the port affinity
for each one doesn't make much sense and there should be a default one.
So only track the entry with lowest priority value.
The commit doesn't affect existing users with a single entry.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 063bd355595428750803d8736a9bb7c8db67d42d ]
Fix a refcount use after free warning due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process released its refcount but didn't release the index yet. Fix it
by adding the needed spin lock.
It fixes the following warning trace:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 11 PID: 540311 at lib/refcount.c:25 refcount_warn_saturate+0x80/0xe0
...
RIP: 0010:refcount_warn_saturate+0x80/0xe0
...
Call Trace:
<TASK>
mlx5_cmd_trigger_completions+0x293/0x340 [mlx5_core]
mlx5_cmd_flush+0x3a/0xf0 [mlx5_core]
enter_error_state+0x44/0x80 [mlx5_core]
mlx5_fw_fatal_reporter_err_work+0x37/0xe0 [mlx5_core]
process_one_work+0x1be/0x390
worker_thread+0x4d/0x3d0
? rescuer_thread+0x350/0x350
kthread+0x141/0x160
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK>
Fixes: 50b2412b7e78 ("net/mlx5: Avoid possible free of command entry while timeout comp handler")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
prestera_switch_set_base_mac_addr
[ Upstream commit c9ffa3e2bc451816ce0295e40063514fabf2bd36 ]
This node pointer is returned by of_find_compatible_node() with
refcount incremented. Calling of_node_put() to aovid the refcount leak.
Fixes: 501ef3066c89 ("net: marvell: prestera: Add driver for Prestera family ASIC devices")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2169b79258c8be803d2595d6456b1e77129fe154 ]
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: b7370112f519 ("lpc32xx: Added ethernet driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6babfc6e6fab068018c36e8f6605184b8c0b349d ]
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: 8a2c9a5ab4b9 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b19ab4b38b06aae12442b2de95ccf58b5dc53584 ]
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. Calling of_node_put() to avoid the
refcount leak. As the remove function do.
Fixes: 5cdaaa12866e ("net: emaclite: adding MDIO and phy lib support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220308024751.2320-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ad35ffa252af67d4cc7c744b9377a2b577748e3f ]
Change curr_link_speed advertised speed, due to
link_info.link_speed is not equal phy.curr_user_speed_req.
Without this patch it is impossible to set advertised
speed to same as link_speed.
Testing Hints: Try to set advertised speed
to 25G only with 25G default link (use ethtool -s 0x80000000)
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3d97f1afd8d831e0c0dc1157418f94b8faa97b54 ]
ice_misc_intr() is an irq handler. It should not sleep.
Use GFP_ATOMIC instead of GFP_KERNEL when allocating some memory.
Fixes: 348048e724a0 ("ice: Implement iidc operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97b0129146b1544bbb0773585327896da3bb4e0a ]
When a bonded interface is destroyed, .ndo_change_mtu can be called
during the tear-down process while the RTNL lock is held. This is a
problem since the auxiliary driver linked to the LAN driver needs to be
notified of the MTU change, and this requires grabbing a device_lock on
the auxiliary_device's dev. Currently this is being attempted in the
same execution context as the call to .ndo_change_mtu which is causing a
dead-lock.
Move the notification of the changed MTU to a separate execution context
(watchdog service task) and eliminate the "before" notification.
Fixes: 348048e724a0e ("ice: Implement iidc operations")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79498d5af8e458102242d1667cf44df1f1564e63 ]
The ice_vc_send_msg_to_vf function has logic to detect "failure"
responses being sent to a VF. If a VF is sent more than
ICE_DFLT_NUM_INVAL_MSGS_ALLOWED then the VF is marked as disabled.
Almost identical logic also existed in the i40e driver.
This logic was added to the ice driver in commit 1071a8358a28 ("ice:
Implement virtchnl commands for AVF support") which itself copied from
the i40e implementation in commit 5c3c48ac6bf5 ("i40e: implement virtual
device interface").
Neither commit provides a proper explanation or justification of the
check. In fact, later commits to i40e changed the logic to allow
bypassing the check in some specific instances.
The "logic" for this seems to be that error responses somehow indicate a
malicious VF. This is not really true. The PF might be sending an error
for any number of reasons such as lack of resources, etc.
Additionally, this causes the PF to log an info message for every failed
VF response which may confuse users, and can spam the kernel log.
This behavior is not documented as part of any requirement for our
products and other operating system drivers such as the FreeBSD
implementation of our drivers do not include this type of check.
In fact, the change from dev_err to dev_info in i40e commit 18b7af57d9c1
("i40e: Lower some message levels") explains that these messages
typically don't actually indicate a real issue. It is quite likely that
a user who hits this in practice will be very confused as the VF will be
disabled without an obvious way to recover.
We already have robust malicious driver detection logic using actual
hardware detection mechanisms that detect and prevent invalid device
usage. Remove the logic since its not a documented requirement and the
behavior is not intuitive.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5710ab79166504013f7c0ae6a57e7d2fd26e5c43 ]
The i40e_vc_send_msg_to_vf_ex (and its wrapper i40e_vc_send_msg_to_vf)
function has logic to detect "failure" responses sent to the VF. If a VF
is sent more than I40E_DEFAULT_NUM_INVALID_MSGS_ALLOWED, then the VF is
marked as disabled. In either case, a dev_info message is printed
stating that a VF opcode failed.
This logic originates from the early implementation of VF support in
commit 5c3c48ac6bf5 ("i40e: implement virtual device interface").
That commit did not go far enough. The "logic" for this behavior seems
to be that error responses somehow indicate a malicious VF. This is not
really true. The PF might be sending an error for any number of reasons
such as lacking resources, an unsupported operation, etc. This does not
indicate a malicious VF. We already have a separate robust malicious VF
detection which relies on hardware logic to detect and prevent a variety
of behaviors.
There is no justification for this behavior in the original
implementation. In fact, a later commit 18b7af57d9c1 ("i40e: Lower some
message levels") reduced the opcode failure message from a dev_err to a
dev_info. In addition, recent commit 01cbf50877e6 ("i40e: Fix to not
show opcode msg on unsuccessful VF MAC change") changed the logic to
allow quieting it for expected failures.
That commit prevented this logic from kicking in for specific
circumstances. This change did not go far enough. The behavior is not
documented nor is it part of any requirement for our products. Other
operating systems such as the FreeBSD implementation of our driver do
not include this logic.
It is clear this check does not make sense, and causes problems which
led to ugly workarounds.
Fix this by just removing the entire logic and the need for the
i40e_vc_send_msg_to_vf_ex function.
Fixes: 01cbf50877e6 ("i40e: Fix to not show opcode msg on unsuccessful VF MAC change")
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2cf29e55894886965722e6625f6a03630b4db31d ]
Modify netdev->features for vlan stripping based on virtual
channel messages received from the PF. Change is needed
to synchronize vlan strip status between PF sysfs and iavf ethtool.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Norbert Ciosek <norbertx.ciosek@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e5417cbf7ab5df1632e68fe7d9e6331fc0e7dbd6 ]
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9470c29faa91c804aa04de4c10634bf02462bfa5 ]
It turns out that DE3 manual has inverted YUV and YVU format numbers for
P010 and P210. Invert them.
This was tested by playing video decoded to P010 and additionally
confirmed by looking at BSP driver source.
Fixes: 169ca4b38932 ("drm/sun4i: Add separate DE3 VI layer formats")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220228181436.1424550-1-jernej.skrabec@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
