summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2022-02-01net: stmmac: dwmac-visconti: Fix clock configuration for RMII modeYuji Ishikawa1-11/+21
[ Upstream commit 0959bc4bd4206433ed101a1332a23e93ad16ec77 ] Bit pattern of the ETHER_CLOCK_SEL register for RMII/MII mode should be fixed. Also, some control bits should be modified with a specific sequence. Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp> Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01net: stmmac: dwmac-visconti: Fix bit definitions for ETHER_CLK_SELYuji Ishikawa1-5/+5
[ Upstream commit 1ba1a4a90fa416a6f389206416c5f488cf8b1543 ] just 0 should be used to represent cleared bits * ETHER_CLK_SEL_DIV_SEL_20 * ETHER_CLK_SEL_TX_CLK_EXT_SEL_IN * ETHER_CLK_SEL_RX_CLK_EXT_SEL_IN * ETHER_CLK_SEL_TX_CLK_O_TX_I * ETHER_CLK_SEL_RMII_CLK_SEL_IN Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp> Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01net: phy: broadcom: hook up soft_reset for BCM54616SRobert Hancock1-0/+1
[ Upstream commit d15c7e875d44367005370e6a82e8f3a382a04f9b ] A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which is a 1 Gbps copper module operating in SGMII mode with an internal BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the module would work properly on the initial insertion or boot of the device, but after the device was rebooted, the link would either only come up at 100 Mbps speeds or go up and down erratically. I found no meaningful changes in the PHY configuration registers between the working and non-working boots, but the status registers seemed to have a lot of error indications set on the SERDES side of the device on the non-working boot. I suspect the problem is that whatever happens on the SGMII link when the device is rebooted and the FPGA logic gets reloaded ends up putting the module's onboard PHY into a bad state. Since commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") the genphy_soft_reset call is not made automatically by the PHY core unless the callback is explicitly specified in the driver structure. For most of these Broadcom devices, there is probably a hardware reset that gets asserted to reset the PHY during boot, however for SFP modules (where the BCM54616S is commonly found) no such reset line exists, so if the board keeps the SFP cage powered up across a reboot, it will end up with no reset occurring during reboots. Hook up the genphy_soft_reset callback for BCM54616S to ensure that a PHY reset is performed before the device is initialized. This appears to fix the issue with erratic operation after a reboot with this SFP module. Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01drm/msm/dsi: invalid parameter check in msm_dsi_phy_enableJosé Expósito1-1/+3
commit 5e761a2287234bc402ba7ef07129f5103bcd775c upstream. The function performs a check on the "phy" input parameter, however, it is used before the check. Initialize the "dev" variable after the sanity check to avoid a possible NULL pointer dereference. Fixes: 5c8290284402b ("drm/msm/dsi: Split PHY drivers to separate files") Addresses-Coverity-ID: 1493860 ("Null pointer dereference") Signed-off-by: José Expósito <jose.exposito89@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220116181844.7400-1-jose.exposito89@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/msm/dsi: Fix missing put_device() call in dsi_get_phyMiaoqian Lin1-1/+6
commit c04c3148ca12227d92f91b355b4538cc333c9922 upstream. If of_find_device_by_node() succeeds, dsi_get_phy() doesn't a corresponding put_device(). Thus add put_device() to fix the exception handling. Fixes: ec31abf ("drm/msm/dsi: Separate PHY to another platform device") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20211230070943.18116-1-linmq006@gmail.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/msm: Fix wrong size calculationXianting Tian1-1/+1
commit 0a727b459ee39bd4c5ced19d6024258ac87b6b2e upstream. For example, memory-region in .dts as below, reg = <0x0 0x50000000 0x0 0x20000000> We can get below values, struct resource r; r.start = 0x50000000; r.end = 0x6fffffff; So the size should be: size = r.end - r.start + 1 = 0x20000000 Signed-off-by: Xianting Tian <xianting.tian@linux.alibaba.com> Fixes: 072f1f9168ed ("drm/msm: add support for "stolen" mem") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220112123334.749776-1-xianting.tian@linux.alibaba.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01hwmon: (lm90) Reduce maximum conversion rate for G781Guenter Roeck1-1/+1
[ Upstream commit a66c5ed539277b9f2363bbace0dba88b85b36c26 ] According to its datasheet, G781 supports a maximum conversion rate value of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only support a maximum conversion rate value of 7 (125 ms). On the other side, chips labeled G781-1 and G784 were found to support a conversion rate value of 8. There is no known means to distinguish G780 from G781 or G784; all chips report the same manufacturer ID and chip revision. Setting the conversion rate register value to 8 on chips not supporting it causes unexpected behavior since the real conversion rate is set to 0 (16 seconds) if a value of 8 is written into the conversion rate register. Limit the conversion rate register value to 7 for all G78x chips to avoid the problem. Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01hwmon: (lm90) Mark alert as broken for MAX6680Guenter Roeck1-1/+1
commit 94746b0ba479743355e0d3cc1cb9cfe3011fb8be upstream. Experiments with MAX6680 and MAX6681 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2022-02-01hwmon: (lm90) Mark alert as broken for MAX6646/6647/6649Guenter Roeck1-1/+1
commit f614629f9c1080dcc844a8430e3fb4c37ebbf05d upstream. Experiments with MAX6646 and MAX6648 show that the alert function of those chips is broken, similar to other chips supported by the lm90 driver. Mark it accordingly. Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01scsi: bnx2fc: Flush destroy_work queue before calling bnx2fc_interface_put()John Meneghini1-15/+5
commit 847f9ea4c5186fdb7b84297e3eeed9e340e83fce upstream. The bnx2fc_destroy() functions are removing the interface before calling destroy_work. This results multiple WARNings from sysfs_remove_group() as the controller rport device attributes are removed too early. Replace the fcoe_port's destroy_work queue. It's not needed. The problem is easily reproducible with the following steps. Example: $ dmesg -w & $ systemctl enable --now fcoe $ fipvlan -s -c ens2f1 $ fcoeadm -d ens2f1.802 [ 583.464488] host2: libfc: Link down on port (7500a1) [ 583.472651] bnx2fc: 7500a1 - rport not created Yet!! [ 583.490468] ------------[ cut here ]------------ [ 583.538725] sysfs group 'power' not found for kobject 'rport-2:0-0' [ 583.568814] WARNING: CPU: 3 PID: 192 at fs/sysfs/group.c:279 sysfs_remove_group+0x6f/0x80 [ 583.607130] Modules linked in: dm_service_time 8021q garp mrp stp llc bnx2fc cnic uio rpcsec_gss_krb5 auth_rpcgss nfsv4 ... [ 583.942994] CPU: 3 PID: 192 Comm: kworker/3:2 Kdump: loaded Not tainted 5.14.0-39.el9.x86_64 #1 [ 583.984105] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013 [ 584.016535] Workqueue: fc_wq_2 fc_rport_final_delete [scsi_transport_fc] [ 584.050691] RIP: 0010:sysfs_remove_group+0x6f/0x80 [ 584.074725] Code: ff 5b 48 89 ef 5d 41 5c e9 ee c0 ff ff 48 89 ef e8 f6 b8 ff ff eb d1 49 8b 14 24 48 8b 33 48 c7 c7 ... [ 584.162586] RSP: 0018:ffffb567c15afdc0 EFLAGS: 00010282 [ 584.188225] RAX: 0000000000000000 RBX: ffffffff8eec4220 RCX: 0000000000000000 [ 584.221053] RDX: ffff8c1586ce84c0 RSI: ffff8c1586cd7cc0 RDI: ffff8c1586cd7cc0 [ 584.255089] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb567c15afc00 [ 584.287954] R10: ffffb567c15afbf8 R11: ffffffff8fbe7f28 R12: ffff8c1486326400 [ 584.322356] R13: ffff8c1486326480 R14: ffff8c1483a4a000 R15: 0000000000000004 [ 584.355379] FS: 0000000000000000(0000) GS:ffff8c1586cc0000(0000) knlGS:0000000000000000 [ 584.394419] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 584.421123] CR2: 00007fe95a6f7840 CR3: 0000000107674002 CR4: 00000000000606e0 [ 584.454888] Call Trace: [ 584.466108] device_del+0xb2/0x3e0 [ 584.481701] device_unregister+0x13/0x60 [ 584.501306] bsg_unregister_queue+0x5b/0x80 [ 584.522029] bsg_remove_queue+0x1c/0x40 [ 584.541884] fc_rport_final_delete+0xf3/0x1d0 [scsi_transport_fc] [ 584.573823] process_one_work+0x1e3/0x3b0 [ 584.592396] worker_thread+0x50/0x3b0 [ 584.609256] ? rescuer_thread+0x370/0x370 [ 584.628877] kthread+0x149/0x170 [ 584.643673] ? set_kthread_struct+0x40/0x40 [ 584.662909] ret_from_fork+0x22/0x30 [ 584.680002] ---[ end trace 53575ecefa942ece ]--- Link: https://lore.kernel.org/r/20220115040044.1013475-1-jmeneghi@redhat.com Fixes: 0cbf32e1681d ("[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks") Tested-by: Guangwu Zhang <guazhang@redhat.com> Co-developed-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: John Meneghini <jmeneghi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01scsi: elx: efct: Don't use GFP_KERNEL under spin lockYang Yingliang1-6/+2
commit 61263b3a11a2594b4e898f166c31162236182b5c upstream. GFP_KERNEL/GFP_DMA can't be used under a spin lock. According the comment, els_ios_lock is used to protect els ios list so we can move down the spin lock to avoid using this flag under the lock. Link: https://lore.kernel.org/r/20220111012441.3232527-1-yangyingliang@huawei.com Fixes: 8f406ef72859 ("scsi: elx: libefc: Extended link Service I/O handling") Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01rpmsg: char: Fix race between the release of rpmsg_eptdev and cdevMatthias Kaehlcke1-9/+2
commit 7a534ae89e34e9b51acb5a63dd0f88308178b46a upstream. struct rpmsg_eptdev contains a struct cdev. The current code frees the rpmsg_eptdev struct in rpmsg_eptdev_destroy(), but the cdev is a managed object, therefore its release is not predictable and the rpmsg_eptdev could be freed before the cdev is entirely released. The cdev_device_add/del() API was created to address this issue (see commit '233ed09d7fda ("chardev: add helper function to register char devs with a struct device")'), use it instead of cdev add/del(). Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.2.Idde68b05b88d4a2e6e54766c653f3a6d9e419ce6@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01rpmsg: char: Fix race between the release of rpmsg_ctrldev and cdevSujit Kautkar1-9/+2
commit b7fb2dad571d1e21173c06cef0bced77b323990a upstream. struct rpmsg_ctrldev contains a struct cdev. The current code frees the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the cdev is a managed object, therefore its release is not predictable and the rpmsg_ctrldev could be freed before the cdev is entirely released, as in the backtrace below. [ 93.625603] ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x7c [ 93.636115] WARNING: CPU: 0 PID: 12 at lib/debugobjects.c:488 debug_print_object+0x13c/0x1b0 [ 93.644799] Modules linked in: veth xt_cgroup xt_MASQUERADE rfcomm algif_hash algif_skcipher af_alg uinput ip6table_nat fuse uvcvideo videobuf2_vmalloc venus_enc venus_dec videobuf2_dma_contig hci_uart btandroid btqca snd_soc_rt5682_i2c bluetooth qcom_spmi_temp_alarm snd_soc_rt5682v [ 93.715175] CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: G B 5.4.163-lockdep #26 [ 93.723855] Hardware name: Google Lazor (rev3 - 8) with LTE (DT) [ 93.730055] Workqueue: events kobject_delayed_cleanup [ 93.735271] pstate: 60c00009 (nZCv daif +PAN +UAO) [ 93.740216] pc : debug_print_object+0x13c/0x1b0 [ 93.744890] lr : debug_print_object+0x13c/0x1b0 [ 93.749555] sp : ffffffacf5bc7940 [ 93.752978] x29: ffffffacf5bc7940 x28: dfffffd000000000 [ 93.758448] x27: ffffffacdb11a800 x26: dfffffd000000000 [ 93.763916] x25: ffffffd0734f856c x24: dfffffd000000000 [ 93.769389] x23: 0000000000000000 x22: ffffffd0733c35b0 [ 93.774860] x21: ffffffd0751994a0 x20: ffffffd075ec27c0 [ 93.780338] x19: ffffffd075199100 x18: 00000000000276e0 [ 93.785814] x17: 0000000000000000 x16: dfffffd000000000 [ 93.791291] x15: ffffffffffffffff x14: 6e6968207473696c [ 93.796768] x13: 0000000000000000 x12: ffffffd075e2b000 [ 93.802244] x11: 0000000000000001 x10: 0000000000000000 [ 93.807723] x9 : d13400dff1921900 x8 : d13400dff1921900 [ 93.813200] x7 : 0000000000000000 x6 : 0000000000000000 [ 93.818676] x5 : 0000000000000080 x4 : 0000000000000000 [ 93.824152] x3 : ffffffd0732a0fa4 x2 : 0000000000000001 [ 93.829628] x1 : ffffffacf5bc7580 x0 : 0000000000000061 [ 93.835104] Call trace: [ 93.837644] debug_print_object+0x13c/0x1b0 [ 93.841963] __debug_check_no_obj_freed+0x25c/0x3c0 [ 93.846987] debug_check_no_obj_freed+0x18/0x20 [ 93.851669] slab_free_freelist_hook+0xbc/0x1e4 [ 93.856346] kfree+0xfc/0x2f4 [ 93.859416] rpmsg_ctrldev_release_device+0x78/0xb8 [ 93.864445] device_release+0x84/0x168 [ 93.868310] kobject_cleanup+0x12c/0x298 [ 93.872356] kobject_delayed_cleanup+0x10/0x18 [ 93.876948] process_one_work+0x578/0x92c [ 93.881086] worker_thread+0x804/0xcf8 [ 93.884963] kthread+0x2a8/0x314 [ 93.888303] ret_from_fork+0x10/0x18 The cdev_device_add/del() API was created to address this issue (see commit '233ed09d7fda ("chardev: add helper function to register char devs with a struct device")'), use it instead of cdev add/del(). Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Signed-off-by: Sujit Kautkar <sujitka@chromium.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: fix unsigned stat widthsJoe Damato3-7/+7
commit 3b8428b84539c78fdc8006c17ebd25afd4722d51 upstream. Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match the width of the stats counters in struct i40e_rx_queue_stats. Update debugfs code to use the correct format specifier for u64. Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Joe Damato <jdamato@fastly.com> Reported-by: kernel test robot <lkp@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix for failed to init adminq while VF resetKaren Sornek3-2/+46
commit 0f344c8129a5337dae50e31b817dd50a60ff238c upstream. Fix for failed to init adminq: -53 while VF is resetting via MAC address changing procedure. Added sync module to avoid reading deadbeef value in reinit adminq during software reset. Without this patch it is possible to trigger VF reset procedure during reinit adminq. This resulted in an incorrect reading of value from the AQP registers and generated the -53 error. Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Karen Sornek <karen.sornek@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix queues reservation for XDPSylwester Dziedziuch1-0/+14
commit 92947844b8beee988c0ce17082b705c2f75f0742 upstream. When XDP was configured on a system with large number of CPUs and X722 NIC there was a call trace with NULL pointer dereference. i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12 i40e 0000:87:00.0: setup of MAIN VSI failed BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e] Call Trace: ? i40e_reconfig_rss_queues+0x130/0x130 [i40e] dev_xdp_install+0x61/0xe0 dev_xdp_attach+0x18a/0x4c0 dev_change_xdp_fd+0x1e6/0x220 do_setlink+0x616/0x1030 ? ahci_port_stop+0x80/0x80 ? ata_qc_issue+0x107/0x1e0 ? lock_timer_base+0x61/0x80 ? __mod_timer+0x202/0x380 rtnl_setlink+0xe5/0x170 ? bpf_lsm_binder_transaction+0x10/0x10 ? security_capable+0x36/0x50 rtnetlink_rcv_msg+0x121/0x350 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x50/0xf0 netlink_unicast+0x1d3/0x2a0 netlink_sendmsg+0x22a/0x440 sock_sendmsg+0x5e/0x60 __sys_sendto+0xf0/0x160 ? __sys_getsockname+0x7e/0xc0 ? _copy_from_user+0x3c/0x80 ? __sys_setsockopt+0xc8/0x1a0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f83fa7a39e0 This was caused by PF queue pile fragmentation due to flow director VSI queue being placed right after main VSI. Because of this main VSI was not able to resize its queue allocation for XDP resulting in no queues allocated for main VSI when XDP was turned on. Fix this by always allocating last queue in PF queue pile for a flow director VSI. Fixes: 41c445ff0f48 ("i40e: main driver core") Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Fix issue when maximum queues is exceededJedrzej Jagielski3-13/+61
commit d701658a50a471591094b3eb3961b4926cc8f104 upstream. Before this patch VF interface vanished when maximum queue number was exceeded. Driver tried to add next queues even if there was not enough space. PF sent incorrect number of queues to the VF when there were not enough of them. Add an additional condition introduced to check available space in 'qp_pile' before proceeding. This condition makes it impossible to add queues if they number is greater than the number resulting from available space. Also add the search for free space in PF queue pair piles. Without this patch VF interfaces are not seen when available space for queues has been exceeded and following logs appears permanently in dmesg: "Unable to get VF config (-32)". "VF 62 failed opcode 3, retval: -5" "Unable to get VF config due to PF error condition, not retrying" Fixes: 7daa6bf3294e ("i40e: driver core headers") Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01i40e: Increase delay to 1 s after global EMP resetJedrzej Jagielski1-9/+3
commit 9b13bd53134c9ddd544a790125199fdbdb505e67 upstream. Recently simplified i40e_rebuild causes that FW sometimes is not ready after NVM update, the ping does not return. Increase the delay in case of EMP reset. Old delay of 300 ms was introduced for specific cards for 710 series. Now it works for all the cards and delay was increased. Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01ucsi_ccg: Check DEV_INT bit only when starting CCG4Sing-Han Chen1-1/+1
commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream. CCGx clears Bit 0:Device Interrupt in the INTR_REG if CCGx is reset successfully. However, there might be a chance that other bits in INTR_REG are not cleared due to internal data queued in PPM. This case misleads the driver that CCGx reset failed. The commit checks bit 0 in INTR_REG and ignores other bits. The ucsi driver would reset PPM later. Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx") Cc: stable@vger.kernel.org Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Sing-Han Chen <singhanc@nvidia.com> Signed-off-by: Wayne Chang <waynec@nvidia.com> Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: typec: tcpm: Do not disconnect when receiving VSAFE0VBadhri Jagan Sridharan1-0/+4
commit 746f96e7d6f7a276726860f696671766bfb24cf0 upstream. With some chargers, vbus might momentarily raise above VSAFE5V and fall back to 0V causing VSAFE0V to be triggered. This will will report a VBUS off event causing TCPM to transition to SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state. Stub from the spec: "4.5.2.2.4.2 Exiting from AttachWait.SNK State A Sink shall transition to Unattached.SNK when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce. A DRP shall transition to Unattached.SRC when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce." [23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected] [23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [23.300579] VBUS off [23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS] [23.301014] VBUS VSAFE0V [23.301111] Start toggling Fixes: 28b43d3d746b8 ("usb: typec: tcpm: Introduce vsafe0v for vbus") Cc: stable@vger.kernel.org Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: typec: tcpm: Do not disconnect while receiving VBUS offBadhri Jagan Sridharan1-1/+2
commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream. With some chargers, vbus might momentarily raise above VSAFE5V and fall back to 0V before tcpm gets to read port->tcpc->get_vbus. This will will report a VBUS off event causing TCPM to transition to SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state. Stub from the spec: "4.5.2.2.4.2 Exiting from AttachWait.SNK State A Sink shall transition to Unattached.SNK when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce. A DRP shall transition to Unattached.SRC when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce." [23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected] [23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS] [23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS] [23.300579] VBUS off [23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS] [23.301014] VBUS VSAFE0V [23.301111] Start toggling Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable@vger.kernel.org Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: typec: tcpci: don't touch CC line if it's Vconn sourceXu Yang2-0/+27
commit 5638b0dfb6921f69943c705383ff40fb64b987f2 upstream. With the AMS and Collision Avoidance, tcpm often needs to change the CC's termination. When one CC line is sourcing Vconn, if we still change its termination, the voltage of the another CC line is likely to be fluctuant and unstable. Therefore, we should verify whether a CC line is sourcing Vconn before changing its termination and only change the termination that is not a Vconn line. This can be done by reading the Vconn Present bit of POWER_ STATUS register. To determine the polarity, we can read the Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be sourced if Plug Orientation is set. Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance") cc: <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01USB: core: Fix hang in usb_kill_urb by adding memory barriersAlan Stern2-0/+26
commit 26fbe9772b8c459687930511444ce443011f86bf upstream. The syzbot fuzzer has identified a bug in which processes hang waiting for usb_kill_urb() to return. It turns out the issue is not unlinking the URB; that works just fine. Rather, the problem arises when the wakeup notification that the URB has completed is not received. The reason is memory-access ordering on SMP systems. In outline form, usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on different CPUs perform the following actions: CPU 0 CPU 1 ---------------------------- --------------------------------- usb_kill_urb(): __usb_hcd_giveback_urb(): ... ... atomic_inc(&urb->reject); atomic_dec(&urb->use_count); ... ... wait_event(usb_kill_urb_queue, atomic_read(&urb->use_count) == 0); if (atomic_read(&urb->reject)) wake_up(&usb_kill_urb_queue); Confining your attention to urb->reject and urb->use_count, you can see that the overall pattern of accesses on CPU 0 is: write urb->reject, then read urb->use_count; whereas the overall pattern of accesses on CPU 1 is: write urb->use_count, then read urb->reject. This pattern is referred to in memory-model circles as SB (for "Store Buffering"), and it is well known that without suitable enforcement of the desired order of accesses -- in the form of memory barriers -- it is entirely possible for one or both CPUs to execute their reads ahead of their writes. The end result will be that sometimes CPU 0 sees the old un-decremented value of urb->use_count while CPU 1 sees the old un-incremented value of urb->reject. Consequently CPU 0 ends up on the wait queue and never gets woken up, leading to the observed hang in usb_kill_urb(). The same pattern of accesses occurs in usb_poison_urb() and the failure pathway of usb_hcd_submit_urb(). The problem is fixed by adding suitable memory barriers. To provide proper memory-access ordering in the SB pattern, a full barrier is required on both CPUs. The atomic_inc() and atomic_dec() accesses themselves don't provide any memory ordering, but since they are present, we can use the optimized smp_mb__after_atomic() memory barrier in the various routines to obtain the desired effect. This patch adds the necessary memory barriers. CC: <stable@vger.kernel.org> Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: dwc3: xilinx: Fix error handling when getting USB3 PHYRobert Hancock1-5/+5
commit 2cc9b1c93b1c4caa2d971856c0780fb5f7d04692 upstream. The code that looked up the USB3 PHY was ignoring all errors other than EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and simplify the code by using devm_phy_optional_get and dev_err_probe so that a missing PHY is not treated as an error and unexpected errors are handled properly. Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms") Cc: stable <stable@vger.kernel.org> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 modeRobert Hancock1-0/+13
commit 9678f3361afc27a3124cd2824aec0227739986fb upstream. It appears that the PIPE clock should not be selected when only USB 2.0 is being used in the design and no USB 3.0 reference clock is used. Also, the core resets are not required if a USB3 PHY is not in use, and will break things if USB3 is actually used but the PHY entry is not listed in the device tree. Skip core resets and register settings that are only required for USB3 mode when no USB3 PHY is specified in the device tree. Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms") Cc: stable <stable@vger.kernel.org> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: cdnsp: Fix segmentation fault in cdns_lost_power functionPawel Laszczak1-3/+3
commit 79aa3e19fe8f5be30e846df8a436bfe306e8b1a6 upstream. CDNSP driver read not initialized cdns->otg_v0_regs which lead to segmentation fault. Patch fixes this issue. Fixes: 2cf2581cd229 ("usb: cdns3: add power lost support for system resume") cc: <stable@vger.kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: gadget: f_sourcesink: Fix isoc transfer for USB_SPEED_SUPER_PLUSPavankumar Kondeti1-0/+1
commit 904edf8aeb459697129be5fde847e2a502f41fd9 upstream. Currently when gadget enumerates in super speed plus, the isoc endpoint request buffer size is not calculated correctly. Fix this by checking the gadget speed against USB_SPEED_SUPER_PLUS and update the request buffer size. Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.") Cc: stable <stable@vger.kernel.org> Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com> Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: common: ulpi: Fix crash in ulpi_match()Jon Hunter1-2/+5
commit 2e3dd4a6246945bf84ea6f478365d116e661554c upstream. Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash on the Tegra20 Ventana platform in the ulpi_match() function. The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS, registers a ulpi_driver but this driver does not provide an 'id_table', so when ulpi_match() is called on the Tegra20 Ventana platform, it crashes when attempting to deference the id_table pointer which is not valid. The Qualcomm USB HS PHY driver uses device-tree for matching the ULPI driver with the device and so fix this crash by using device-tree for matching if the id_table is not valid. Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb: xhci-plat: fix crash when suspend if remote wake enableFrank Li1-0/+3
commit 9df478463d9feb90dae24f183383961cf123a0ec upstream. Crashed at i.mx8qm platform when suspend if enable remote wakeup Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP Modules linked in: CPU: 2 PID: 244 Comm: kworker/u12:6 Not tainted 5.15.5-dirty #12 Hardware name: Freescale i.MX8QM MEK (DT) Workqueue: events_unbound async_run_entry_fn pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : xhci_disable_hub_port_wake.isra.62+0x60/0xf8 lr : xhci_disable_hub_port_wake.isra.62+0x34/0xf8 sp : ffff80001394bbf0 x29: ffff80001394bbf0 x28: 0000000000000000 x27: ffff00081193b578 x26: ffff00081193b570 x25: 0000000000000000 x24: 0000000000000000 x23: ffff00081193a29c x22: 0000000000020001 x21: 0000000000000001 x20: 0000000000000000 x19: ffff800014e90490 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000002 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000960 x9 : ffff80001394baa0 x8 : ffff0008145d1780 x7 : ffff0008f95b8e80 x6 : 000000001853b453 x5 : 0000000000000496 x4 : 0000000000000000 x3 : ffff00081193a29c x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff000814591620 Call trace: xhci_disable_hub_port_wake.isra.62+0x60/0xf8 xhci_suspend+0x58/0x510 xhci_plat_suspend+0x50/0x78 platform_pm_suspend+0x2c/0x78 dpm_run_callback.isra.25+0x50/0xe8 __device_suspend+0x108/0x3c0 The basic flow: 1. run time suspend call xhci_suspend, xhci parent devices gate the clock. 2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend 3. xhci_suspend call xhci_disable_hub_port_wake, which access register, but clock already gated by run time suspend. This problem was hidden by power domain driver, which call run time resume before it. But the below commit remove it and make this issue happen. commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()") This patch call run time resume before suspend to make sure clock is on before access register. Reviewed-by: Peter Chen <peter.chen@kernel.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Frank Li <Frank.Li@nxp.com> Testeb-by: Abel Vesa <abel.vesa@nxp.com> Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01usb-storage: Add unusual-devs entry for VL817 USB-SATA bridgeAlan Stern1-0/+10
commit 5b67b315037250a61861119683e7fcb509deea25 upstream. Two people have reported (and mentioned numerous other reports on the web) that VIA's VL817 USB-SATA bridge does not work with the uas driver. Typical log messages are: [ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD [ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00 [ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd [ 3606.328584] scsi host14: uas_eh_device_reset_handler success Surprisingly, the devices do seem to work okay for some other people. The cause of the differing behaviors is not known. In the hope of getting the devices to work for the most users, even at the possible cost of degraded performance for some, this patch adds an unusual_devs entry for the VL817 to block it from binding to the uas driver by default. Users will be able to override this entry by means of a module parameter, if they want. CC: <stable@vger.kernel.org> Reported-by: DocMAX <mail@vacharakis.de> Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01tty: Add support for Brainboxes UC cards.Cameron Williams1-2/+98
commit 152d1afa834c84530828ee031cf07a00e0fc0b8c upstream. This commit adds support for the some of the Brainboxes PCI range of cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279, UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368 and UC-420/431. Signed-off-by: Cameron Williams <cang1@live.co.uk> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01tty: n_gsm: fix SW flow control encoding/handlingdaniel.starke@siemens.com1-1/+3
commit 8838b2af23caf1ff0610caef2795d6668a013b2d upstream. n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF) are the control characters defined in ISO/IEC 646. These shall be quoted if seen in the data stream to avoid interpretation as flow control characters. ISO/IEC 646 refers to the set of ISO standards described as the ISO 7-bit coded character set for information interchange. Its final version is also known as ITU T.50. See https://www.itu.int/rec/T-REC-T.50-199209-I/en To abide the standard it is needed to quote DC1 and DC3 correctly if these are seen as data bytes and not as control characters. The current implementation already tries to enforce this but fails to catch all defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most significant bit shall be ignored for DC1 and DC3 handling. The current implementation handles only the case with the most significant bit set 0. Cases in which DC1 and DC3 have the most significant bit set 1 are left unhandled. This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only the 7 least significant bits set 1) before comparing them with XON (a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need quotation via byte stuffing. Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01serial: stm32: fix software flow control transferValentin Caron1-1/+1
commit 037b91ec7729524107982e36ec4b40f9b174f7a2 upstream. x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty. Fix start_tx condition to allow x_char to be sent. Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver") Cc: stable <stable@vger.kernel.org> Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01serial: 8250: of: Fix mapped region size when using reg-offset propertyRobert Hancock1-1/+10
commit d06b1cf28297e27127d3da54753a3a01a2fa2f28 upstream. 8250_of supports a reg-offset property which is intended to handle cases where the device registers start at an offset inside the region of memory allocated to the device. The Xilinx 16550 UART, for which this support was initially added, requires this. However, the code did not adjust the overall size of the mapped region accordingly, causing the driver to request an area of memory past the end of the device's allocation. For example, if the UART was allocated an address of 0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device tree, the region of memory reserved was b0131000-b0140fff, which caused the driver for the region starting at b0140000 to fail to probe. Fix this by subtracting reg-offset from the mapped region size. Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.) Cc: stable <stable@vger.kernel.org> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01serial: pl011: Fix incorrect rs485 RTS polarity on set_mctrlJochen Mades1-2/+6
commit 62f676ff7898f6c1bd26ce014564773a3dc00601 upstream. Commit 8d479237727c ("serial: amba-pl011: add RS485 support") sought to keep RTS deasserted on set_mctrl if rs485 is enabled. However it did so only if deasserted RTS polarity is high. Fix it in case it's low. Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support") Cc: stable@vger.kernel.org # v5.15+ Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Signed-off-by: Jochen Mades <jochen@mades.net> [lukas: copyedit commit message, add stable designation] Signed-off-by: Lukas Wunner <lukas@wunner.de> Link: https://lore.kernel.org/r/85fa3323ba8c307943969b7343e23f34c3e652ba.1642909284.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01dm: properly fix redundant bio-based IO accountingMike Snitzer1-2/+3
commit b879f915bc48a18d4f4462729192435bb0f17052 upstream. Record the start_time for a bio but defer the starting block core's IO accounting until after IO is submitted using bio_start_io_acct_time(). This approach avoids the need to mess around with any of the individual IO stats in response to a bio_split() that follows bio submission. Reported-by: Bud Brown <bubrown@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Depends-on: e45c47d1f94e ("block: add bio_start_io_acct_time() to control start_time") Signed-off-by: Mike Snitzer <snitzer@redhat.com> Link: https://lore.kernel.org/r/20220128155841.39644-4-snitzer@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01dm: revert partial fix for redundant bio-based IO accountingMike Snitzer1-15/+0
commit f524d9c95fab54783d0038f7a3e8c014d5b56857 upstream. Reverts a1e1cb72d9649 ("dm: fix redundant IO accounting for bios that need splitting") because it was too narrow in scope (only addressed redundant 'sectors[]' accounting and not ios, nsecs[], etc). Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Link: https://lore.kernel.org/r/20220128155841.39644-3-snitzer@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/amd/display: Fix FP start/end for dcn30_internal_validate_bw.Bas Nieuwenhuizen1-2/+2
commit 72a8d87b87270bff0c0b2fed4d59c48d0dd840d7 upstream. It calls populate_dml_pipes which uses doubles to initialize the scale_ratio_depth params. Mirrors the dcn20 logic. Cc: stable@vger.kernel.org Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/atomic: Add the crtc to affected crtc only if uapi.enable = trueManasi Navare1-4/+8
commit 5ec1cebd59300ddd26dbaa96c17c508764eef911 upstream. In case of a modeset where a mode gets split across multiple CRTCs in the driver specific implementation (bigjoiner in i915) we wrongly count the affected CRTCs based on the drm_crtc_mask and indicate the stolen CRTC as an affected CRTC in atomic_check_only(). This triggers a warning since affected CRTCs doent match requested CRTC. To fix this in such bigjoiner configurations, we should only increment affected crtcs if that CRTC is enabled in UAPI not if it is just used internally in the driver to split the mode. v3: Add the same uapi crtc_state->enable check in requested crtc calc (Ville) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Simon Ser <contact@emersion.fr> Cc: Pekka Paalanen <pekka.paalanen@collabora.co.uk> Cc: Daniel Stone <daniels@collabora.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: dri-devel@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v5.11+ Fixes: 919c2299a893 ("drm/i915: Enable bigjoiner") Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211004115913.23889-1-manasi.d.navare@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01drm/etnaviv: relax submit size limitsLucas Stach1-2/+2
commit e3d26528e083e612314d4dcd713f3d5a26143ddc upstream. While all userspace tried to limit commandstreams to 64K in size, a bug in the Mesa driver lead to command streams of up to 128K being submitted. Allow those to avoid breaking existing userspace. Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes") Cc: stable@vger.kernel.org Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01efi: runtime: avoid EFIv2 runtime services on Apple x86 machinesArd Biesheuvel1-0/+7
commit f5390cd0b43c2e54c7cf5506c7da4a37c5cef746 upstream. Aditya reports [0] that his recent MacbookPro crashes in the firmware when using the variable services at runtime. The culprit appears to be a call to QueryVariableInfo(), which we did not use to call on Apple x86 machines in the past as they only upgraded from EFI v1.10 to EFI v2.40 firmware fairly recently, and QueryVariableInfo() (along with UpdateCapsule() et al) was added in EFI v2.00. The only runtime service introduced in EFI v2.00 that we actually use in Linux is QueryVariableInfo(), as the capsule based ones are optional, generally not used at runtime (all the LVFS/fwupd firmware update infrastructure uses helper EFI programs that invoke capsule update at boot time, not runtime), and not implemented by Apple machines in the first place. QueryVariableInfo() is used to 'safely' set variables, i.e., only when there is enough space. This prevents machines with buggy firmwares from corrupting their NVRAMs when they run out of space. Given that Apple machines have been using EFI v1.10 services only for the longest time (the EFI v2.0 spec was released in 2006, and Linux support for the newly introduced runtime services was added in 2011, but the MacbookPro12,1 released in 2015 still claims to be EFI v1.10 only), let's avoid the EFI v2.0 ones on all Apple x86 machines. [0] https://lore.kernel.org/all/6D757C75-65B1-468B-842D-10410081A8E4@live.com/ Cc: <stable@vger.kernel.org> Cc: Jeremy Kerr <jk@ozlabs.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Reported-by: Aditya Garg <gargaditya08@live.com> Tested-by: Orlando Chamberlain <redecorating@protonmail.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Tested-by: Aditya Garg <gargaditya08@live.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215277 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01scsi: zfcp: Fix failed recovery on gone remote port with non-NPIV FCP devicesSteffen Maier1-1/+12
commit 8c9db6679be4348b8aae108e11d4be2f83976e30 upstream. Suppose we have an environment with a number of non-NPIV FCP devices (virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical FCP channel (HBA port) and its I_T nexus. Plus a number of storage target ports zoned to such shared channel. Now one target port logs out of the fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port recovery depending on the ADISC result. This happens on all such FCP devices (in different Linux images) concurrently as they all receive a copy of this RSCN. In the following we look at one of those FCP devices. Requests other than FSF_QTCB_FCP_CMND can be slow until they get a response. Depending on which requests are affected by slow responses, there are different recovery outcomes. Here we want to fix failed recoveries on port or adapter level by avoiding recovery requests that can be slow. We need the cached N_Port_ID for the remote port "link" test with ADISC. Just before sending the ADISC, we now intentionally forget the old cached N_Port_ID. The idea is that on receiving an RSCN for a port, we have to assume that any cached information about this port is stale. This forces a fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for the same port. Since we typically can still communicate with the nameserver efficiently, we now reach steady state quicker: Either the nameserver still does not know about the port so we stop recovery, or the nameserver already knows the port potentially with a new N_Port_ID and we can successfully and quickly perform open port recovery. For the one case, where ADISC returns successfully, we re-initialize port->d_id because that case does not involve any port recovery. This also solves a problem if the storage WWPN quickly logs into the fabric again but with a different N_Port_ID. Such as on virtual WWPN takeover during target NPIV failover. [https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the RSCN from the storage FDISC was ignored by zfcp and we could not successfully recover the failover. On some later failback on the storage, we could have been lucky if the virtual WWPN got the same old N_Port_ID from the SAN switch as we still had cached. Then the related RSCN triggered a successful port reopen recovery. However, there is no guarantee to get the same N_Port_ID on NPIV FDISC. Even though NPIV-enabled FCP devices are not affected by this problem, this code change optimizes recovery time for gone remote ports as a side effect. The timely drop of cached N_Port_IDs prevents unnecessary slow open port attempts. While the problem might have been in code before v2.6.32 commit 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix depends on the gid_pn_work introduced with that commit, so we mark it as culprit to satisfy fix dependencies. Note: Point-to-point remote port is already handled separately and gets its N_Port_ID from the cached peer_d_id. So resetting port->d_id in general does not affect PtP. Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") Cc: <stable@vger.kernel.org> #2.6.32+ Suggested-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01net: stmmac: skip only stmmac_ptp_register when resume from suspendMohammad Athari Bin Ismail1-11/+9
commit 0735e639f129dff455aeb91da291f5c578cc33db upstream. When resume from suspend, besides skipping PTP registration, it also skipping PTP HW initialization. This could cause PTP clock not able to operate properly when resume from suspend. To fix this, only stmmac_ptp_register() is skipped when resume from suspend. Fixes: fe1319291150 ("stmmac: Don't init ptp again when resume from suspend/hibernation") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01net: stmmac: configure PTP clock source prior to PTP initializationMohammad Athari Bin Ismail2-3/+3
commit 94c82de43e01ef5747a95e4a590880de863fe423 upstream. For Intel platform, it is required to configure PTP clock source prior PTP initialization in MAC. So, need to move ptp_clk_freq_config execution from stmmac_ptp_register() to stmmac_init_ptp(). Fixes: 76da35dc99af ("stmmac: intel: Add PSE and PCH PTP clock source selection") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01net: sfp: ignore disabled SFP nodeMarek Behún1-0/+5
commit 2148927e6ed43a1667baf7c2ae3e0e05a44b51a0 upstream. Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") added code which finds SFP bus DT node even if the node is disabled with status = "disabled". Because of this, when phylink is created, it ends with non-null .sfp_bus member, even though the SFP module is not probed (because the node is disabled). We need to ignore disabled SFP bus node. Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages") Signed-off-by: Marek Behún <kabel@kernel.org> Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if ↵Marc Kleine-Budde1-0/+6
length is 0 commit db72589c49fd260bfc99c7160c079675bc7417af upstream. In order to optimize FIFO access, especially on m_can cores attached to slow busses like SPI, in patch | e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors") bulk read/write support has been added to the m_can_fifo_{read,write} functions. That change leads to the tcan driver to call regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0 data length). regmap treats this as an error: | tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22 This patch fixes the problem by not calling the cdev->ops->{read,write)_fifo() in case of a 0 length read/write. Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors") Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Cc: Matt Kline <matt@bitbashing.io> Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com> Reported-by: Michael Anochin <anochin@photo-meter.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-02-01intel-peci-client: Use wr_pkg_cfg struct for write commandJason M. Bills1-5/+1
The write command is incorrectly using the rd_pkg_cfg struct for the PECI command data, which could introduce issues if the structs change in the future. This fixes the write command and the callers (only peci-hwmon.h found using grep) to send the data as a u32 and use the wr_pkg_cfg struct. Tested: Wrote the /sys/class/hwmon/hwmon13/power1_cap attribute which triggers a write command and confirmed that the data written is the same after this change. Signed-off-by: Jason M. Bills <jason.m.bills@intel.com>
2022-01-31Merge tag 'v5.15.18' into dev-5.15Joel Stanley547-3929/+6731
This is the 5.15.18 stable release Signed-off-by: Joel Stanley <joel@jms.id.au>
2022-01-31USB: serial: pl2303: Add IBM device IDsEddie James2-0/+4
IBM manufactures a PL2303 device for UPS communications. Add the vendor and product IDs so that the PL2303 driver binds to the device. OpenBMC-Staging-Count: 1 Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20220128214852.21551-2-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2022-01-31fsi: scom: Remove retries in indirect scomsJoel Stanley1-26/+15
In commit f72ddbe1d7b7 ("fsi: scom: Remove retries") the retries were removed from get and put scoms. That patch missed the retires in get and put indirect scom. For the same reason, remove them from the scom driver to allow the caller to decide to retry. This removes the following special case which would have caused the retry code to return early: - if ((ind_data & XSCOM_DATA_IND_COMPLETE) || (err != SCOM_PIB_BLOCKED)) - return 0; I believe this case is handled. OpenBMC-Staging-Count: 1 Fixes: f72ddbe1d7b7 ("fsi: scom: Remove retries") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20211207033811.518981-3-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-26 16:31:30 +0300