| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We now reference the arp_tbl, which requires IPv4 support to be
enabled in the kernel, otherwise we get a link error:
drivers/net/built-in.o: In function `mlx5e_tc_update_neigh_used_value':
(.text+0x16afec): undefined reference to `arp_tbl'
drivers/net/built-in.o: In function `mlx5e_rep_neigh_init':
en_rep.c:(.text+0x16c16d): undefined reference to `arp_tbl'
drivers/net/built-in.o: In function `mlx5e_rep_netevent_event':
en_rep.c:(.text+0x16cbb5): undefined reference to `arp_tbl'
This adds a Kconfig dependency for it.
Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Track alignment in BPF verifier so that legitimate programs won't be
rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
2) Make tail calls work properly in arm64 BPF JIT, from Deniel
Borkmann.
3) Make the configuration and semantics Generic XDP make more sense and
don't allow both generic XDP and a driver specific instance to be
active at the same time. Also from Daniel.
4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.
5) Fix use-after-free in VRF driver, from Gao Feng.
6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
qca_spi driver, from Stefan Wahren.
7) Always run cleanup routines in BPF samples when we get SIGTERM, from
Andy Gospodarek.
8) The mdio phy code should bring PHYs out of reset using the shared
GPIO lines before invoking bus->reset(). From Florian Fainelli.
9) Some USB descriptor access endian fixes in various drivers from
Johan Hovold.
10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
Pressman.
11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.
12) Cure netdev leak in AF_PACKET when using timestamping via control
messages. From Douglas Caetano dos Santos.
13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
Lichvar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
ldmvsw: stop the clean timer at beginning of remove
ldmvsw: unregistering netdev before disable hardware
net: netcp: fix check of requested timestamping filter
ipv6: avoid dad-failures for addresses with NODAD
qed: Fix uninitialized data in aRFS infrastructure
mdio: mux: fix device_node_continue.cocci warnings
net/packet: fix missing net_device reference release
net/mlx4_core: Use min3 to select number of MSI-X vectors
macvlan: Fix performance issues with vlan tagged packets
net: stmmac: use correct pointer when printing normal descriptor ring
net/mlx5: Use underlay QPN from the root name space
net/mlx5e: IPoIB, Only support regular RQ for now
net/mlx5e: Fix setup TC ndo
net/mlx5e: Fix ethtool pause support and advertise reporting
net/mlx5e: Use the correct pause values for ethtool advertising
vmxnet3: ensure that adapter is in proper state during force_close
sfc: revert changes to NIC revision numbers
net: ch9200: add missing USB-descriptor endianness conversions
net: irda: irda-usb: fix firmware name on big-endian hosts
net: dsa: mv88e6xxx: add default case to switch
...
|
|
Stop the clean timer earlier to be sure there's no asynchronous
interference while stopping the port.
Orabug: 25748241
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running LDom binding/unbinding test, kernel may panic
in ldmvsw_open(). It is more likely that because we're removing
the ldc connection before unregistering the netdev in vsw_port_remove(),
we set up a window of time where one process could be removing the
device while another trying to UP the device. This also sometimes causes
vio handshake error due to opening a device without closing it completely.
We should unregister the netdev before we disable the "hardware".
Orabug: 25980913, 25925306
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver doesn't support timestamping of all received packets and
should return error when trying to enable the HWTSTAMP_FILTER_ALL
filter.
Cc: WingMan Kwok <w-kwok2@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-05-12
This series contains some mlx5 fixes for net.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Fix ethtool pause support and advertise reporting") kernels >= 4.8
("net/mlx5e: Use the correct pause values for ethtool advertising") kernels >= 4.8
v1->v2:
Dropped statistics spinlock patch, it needs some extra work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current memset is using incorrect type of variable, causing the
upper-half of the strucutre to be left uninitialized and causing:
ethernet/qlogic/qed/qed_init_fw_funcs.c: In function 'qed_set_rfs_mode_disable':
ethernet/qlogic/qed/qed_init_fw_funcs.c:993:3: error: '*((void *)&ramline+4)' is used uninitialized in this function [-Werror=uninitialized]
Fixes: d51e4af5c209 ("qed: aRFS infrastructure support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device node iterators put the previous value of the index variable, so an
explicit put causes a double put.
In particular, of_mdiobus_register can fail before doing anything
interesting, so one could view it as a no-op from the reference count
point of view.
Generated by: scripts/coccinelle/iterators/device_node_continue.cocci
CC: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macvlan always turns on offload features that have sofware
fallback (NETIF_GSO_SOFTWARE). This allows much higher guest-guest
communications over macvtap.
However, macvtap does not turn on these features for vlan tagged traffic.
As a result, depending on the HW that mactap is configured on, the
performance of guest-guest communication over a vlan is very
inconsistent. If the HW supports TSO/UFO over vlans, then the
performance will be fine. If not, the the performance will suffer
greatly since the VM may continue using TSO/UFO, and will force the host
segment the traffic and possibly overlow the macvtap queue.
This patch adds the always on offloads to vlan_features. This
makes sure that any vlan tagged traffic between 2 guest will not
be segmented needlessly.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two pointers in sysfs_display_ring,
one that increments if using normal dma descriptors,
another if using extended dma descriptors.
When printing the normal dma descriptors, the wrong pointer is used,
thus the printed descriptor addresses are incorrect.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Root flow table is dynamically changed by the underlying flow steering
layer, and IPoIB/ULPs have no idea what will be the root flow table in
the future, hence we need a dynamic infrastructure to move Underlay QPs
with the root flow table.
Fixes: b3ba51498bdd ("net/mlx5: Refactor create flow table method to accept underlay QP")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
IPoIB doesn't support striding RQ at the moment, for this
we need to explicitly choose non striding RQ in IPoIB init,
even if the HW supports it.
Fixes: 8f493ffd88ea ("net/mlx5e: IPoIB, RX steering RSS RQTs and TIRs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fail-safe support patches introduced a trivial bug,
setup tc callback is doing a wrong check of the netdevice state,
the fix is simply to invert the condition.
Fixes: 6f9485af4020 ("net/mlx5e: Fail safe tc setup")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pause bit should set when RX pause is on, not TX pause.
Also, setting Asym_Pause is incorrect, and should be turned off.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Query the operational pause from firmware (PFCC register) instead of
always passing zeros.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull some more input subsystem updates from Dmitry Torokhov:
"An updated xpad driver with a few more recognized device IDs, and a
new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
via SPI bus"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cros_ec_keyb - remove extraneous 'const'
Input: add support for PlayStation 1/2 joypads connected via SPI
Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
Input: xpad - sync supported devices with xboxdrv
Input: xpad - sort supported devices by USB ID
|
|
Pull UBI/UBIFS updates from Richard Weinberger:
- new config option CONFIG_UBIFS_FS_SECURITY
- minor improvements
- random fixes
* tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs:
ubi: Add debugfs file for tracking PEB state
ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl
ubifs: Remove unnecessary assignment
ubifs: Fix cut and paste error on sb type comparisons
ubi: fastmap: Fix slab corruption
ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels
ubi: Make mtd parameter readable
ubi: Fix section mismatch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"Incremental fixes and a small feature addition on top of the main
libnvdimm 4.12 pull request:
- Geert noticed that tinyconfig was bloated by BLOCK selecting DAX.
The size regression is fixed by moving all dax helpers into the
dax-core and only specifying "select DAX" for FS_DAX and
dax-capable drivers. He also asked for clarification of the
NR_DEV_DAX config option which, on closer look, does not need to be
a config option at all. Mike also throws in a DEV_DAX_PMEM fixup
for good measure.
- Ben's attention to detail on -stable patch submissions caught a
case where the recent fixes to arch_copy_from_iter_pmem() missed a
condition where we strand dirty data in the cache. This is tagged
for -stable and will also be included in the rework of the pmem api
to a proposed {memcpy,copy_user}_flushcache() interface for 4.13.
- Vishal adds a feature that missed the initial pull due to pending
review feedback. It allows the kernel to clear media errors when
initializing a BTT (atomic sector update driver) instance on a pmem
namespace.
- Ross noticed that the dax_device + dax_operations conversion broke
__dax_zero_page_range(). The nvdimm unit tests fail to check this
path, but xfstests immediately trips over it. No excuse for missing
this before submitting the 4.12 pull request.
These all pass the nvdimm unit tests and an xfstests spot check. The
set has received a build success notification from the kbuild robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
filesystem-dax: fix broken __dax_zero_page_range() conversion
libnvdimm, btt: ensure that initializing metadata clears poison
libnvdimm: add an atomic vs process context flag to rw_bytes
x86, pmem: Fix cache flushing for iovec write < 8 bytes
device-dax: kill NR_DEV_DAX
block, dax: move "select DAX" from BLOCK to FS_DAX
device-dax: Tell kbuild DEV_DAX_PMEM depends on DEV_DAX
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull more power-supply updates from Sebastian Reichel:
"The power-supply subsystem has a few more changes for the v4.12 merge
window:
- New battery driver for AXP20X and AXP22X PMICs
- Improve max17042_battery for usage on x86
- Misc small cleanups & fixes"
* tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (34 commits)
power: supply: cpcap-charger: Keep trickle charger bits disabled
power: supply: cpcap-charger: Fix enable for 3.8V charge setting
power: supply: cpcap-charger: Fix charge voltage configuration
power: supply: cpcap-charger: Fix charger name
power: supply: twl4030-charger: make twl4030_bci_property_is_writeable static
power: supply: sbs-battery: Add alert callback
mailmap: add Sebastian Reichel
power: supply: avoid unused twl4030-madc.h
power: supply: sbs-battery: Correct supply status with current draw
power: supply: sbs-battery: Don't ignore the first external power change
power: supply: pda_power: move from timer to delayed_work
power: supply: max17042_battery: Add support for the SCOPE property
power: supply: max17042_battery: Add support for the CHARGE_NOW property
power: supply: max17042_battery: Add support for the CHARGE_FULL_DESIGN property
power: supply: max17042_battery: mAh readings depend on r_sns value
power: supply: max17042_battery: Add support for the VOLT_MIN property
power: supply: max17042_battery: Add support for the TECHNOLOGY attribute
power: supply: max17042_battery: Add external_power_changed callback
power: supply: max17042_battery: Add support for the STATUS property
power: supply: max17042_battery: Add default platform_data fallback data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Fix a problem where orderly_shutdown() is called for multiple times
due to multiple critical overheating events raised in a short period
by platform thermal driver. (Keerthy)
- Introduce a backup thermal shutdown mechanism, which invokes
kernel_power_off()/emergency_restart() directly, after
orderly_shutdown() being issued for certain amount of time(specified
via Kconfig). This is useful in certain conditions that userspace may
be unable to power off the system in a clean manner and leaves the
system in a critical state, like in the middle of driver probing
phase. (Keerthy)
- Introduce a new interface in thermal devfreq_cooling code so that the
driver can provide more precise data regarding actual power to the
thermal governor every time the power budget is calculated. (Lukasz
Luba)
- Introduce BCM 2835 soc thermal driver and northstar thermal driver,
within a new sub-folder. (Rafał Miłecki)
- Introduce DA9062/61 thermal driver. (Steve Twiss)
- Remove non-DT booting on TI-SoC driver. Also add support to fetching
coefficients from DT. (Keerthy)
- Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)
- Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
Brian Bian)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
thermal: core: Add a back up thermal shutdown mechanism
thermal: core: Allow orderly_poweroff to be called only once
Thermal: Intel SoC DTS: Change interrupt request behavior
trace: thermal: add another parameter 'power' to the tracing function
thermal: devfreq_cooling: add new interface for direct power read
thermal: devfreq_cooling: refactor code and add get_voltage function
thermal: mt8173: minor mtk_thermal.c cleanups
thermal: bcm2835: move to the broadcom subdirectory
thermal: broadcom: ns: specify myself as MODULE_AUTHOR
thermal: da9062/61: Thermal junction temperature monitoring driver
Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
thermal: broadcom: add Northstar thermal driver
dt-bindings: thermal: add support for Broadcom's Northstar thermal
thermal: bcm2835: add thermal driver for bcm2835 SoC
dt-bindings: Add thermal zone to bcm2835-thermal example
thermal: rcar_gen3_thermal: add suspend and resume support
thermal: rcar_gen3_thermal: store device match data in private structure
thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
thermal: rcar_gen3_thermal: record and check number of TSCs found
thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
...
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"AMD, nouveau, one i915, and one EDID fix for v4.12-rc1
Some fixes that it would be good to have in rc1. It contains the i915
quiet fix that you reported.
It also has an amdgpu fixes pull, with lots of ongoing work on Vega10
which is new in this kernel and is preliminary support so may have a
fair bit of movement.
Otherwise a few non-Vega10 AMD fixes, one EDID fix and some nouveau
regression fixers"
* tag 'drm-fixes-for-v4.12-rc1' of git://people.freedesktop.org/~airlied/linux: (144 commits)
drm/i915: Make vblank evade warnings optional
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
drm/nouveau/tmr: handle races with hw when updating the next alarm time
drm/nouveau/tmr: ack interrupt before processing alarms
drm/nouveau/core: fix static checker warning
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
drm/nouveau/kms/nv50: fix source-rect-only plane updates
drm/nouveau/kms/nv50: remove pointless argument to window atomic_check_acquire()
drm/amd/powerplay: refine pwm1_enable callback functions for CI.
drm/amd/powerplay: refine pwm1_enable callback functions for vi.
drm/amd/powerplay: refine pwm1_enable callback functions for Vega10.
drm/amdgpu: refine amdgpu pwm1_enable sysfs interface.
drm/amdgpu: add amd fan ctrl mode enums.
drm/amd/powerplay: add more smu message on Vega10.
drm/amdgpu: fix dependency issue
drm/amd: fix init order of sched job
drm/amdgpu: add some additional vega10 pci ids
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"Things were a lot more calm than previously expected. It's primarily
fixes in various areas, with most of the new functionality centering
around TCMU backend driver work that Xiubo Li has been driving.
Here's the summary on the feature side:
- Make T10-PI verify configurable for emulated (FILEIO + RD) backends
(Dmitry Monakhov)
- Allow target-core/TCMU pass-through to use in-kernel SPC-PR logic
(Bryant Ly + MNC)
- Add TCMU support for growing ring buffer size (Xiubo Li + MNC)
- Add TCMU support for global block data pool (Xiubo Li + MNC)
and on the bug-fix side:
- Fix COMPARE_AND_WRITE non GOOD status handling for READ phase
failures (Gary Guo + nab)
- Fix iscsi-target hang with explicitly changing per NodeACL
CmdSN number depth with concurrent login driven session
reinstatement. (Gary Guo + nab)
- Fix ibmvscsis fabric driver ABORT task handling (Bryant Ly)
- Fix target-core/FILEIO zero length handling (Bart Van Assche)
Also, there was an OOPs introduced with the WRITE_VERIFY changes that
I ended up reverting at the last minute, because as not unusual Bart
and I could not agree on the fix in time for -rc1. Since it's specific
to a conformance test, it's been reverted for now.
There is a separate patch in the queue to address the underlying
control CDB write overflow regression in >= v4.3 separate from the
WRITE_VERIFY revert here, that will be pushed post -rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (30 commits)
Revert "target: Fix VERIFY and WRITE VERIFY command parsing"
IB/srpt: Avoid that aborting a command triggers a kernel warning
IB/srpt: Fix abort handling
target/fileio: Fix zero-length READ and WRITE handling
ibmvscsis: Do not send aborted task response
tcmu: fix module removal due to stuck thread
target: Don't force session reset if queue_depth does not change
iscsi-target: Set session_fall_back_to_erl0 when forcing reinstatement
target: Fix compare_and_write_callback handling for non GOOD status
tcmu: Recalculate the tcmu_cmd size to save cmd area memories
tcmu: Add global data block pool support
tcmu: Add dynamic growing data area feature support
target: fixup error message in target_tg_pt_gp_tg_pt_gp_id_store()
target: fixup error message in target_tg_pt_gp_alua_access_type_store()
target/user: PGR Support
target: Add WRITE_VERIFY_16
Documentation/target: add an example script to configure an iSCSI target
target: Use kmalloc_array() in transport_kmap_data_sg()
target: Use kmalloc_array() in compare_and_write_callback()
target: Improve size determinations in two functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A single ARM Juno clocksource driver fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/arm_arch_timer: Fix arch_timer_mem_find_best_frame()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
|
|
Pull MIPS updates from James Hogan:
"math-emu:
- Add missing clearing of BLTZALL and BGEZALL emulation counters
- Fix BC1EQZ and BC1NEZ condition handling
- Fix BLEZL and BGTZL identification
BPF:
- Add JIT support for SKF_AD_HATYPE
- Use unsigned access for unsigned SKB fields
- Quit clobbering callee saved registers in JIT code
- Fix multiple problems in JIT skb access helpers
Loongson 3:
- Select MIPS_L1_CACHE_SHIFT_6
Octeon:
- Remove vestiges of CONFIG_CAVIUM_OCTEON_2ND_KERNEL
- Remove unused L2C types and macros.
- Remove unused SLI types and macros.
- Fix compile error when USB is not enabled.
- Octeon: Remove unused PCIERCX types and macros.
- Octeon: Clean up platform code.
SNI:
- Remove recursive include of cpu-feature-overrides.h
Sibyte:
- Export symbol periph_rev to sb1250-mac network driver.
- Fix Kconfig warning.
Generic platform:
- Enable Root FS on NFS in generic_defconfig
SMP-MT:
- Use CPU interrupt controller IPI IRQ domain support
UASM:
- Add support for LHU for uasm.
- Remove needless ISA abstraction
mm:
- Add 48-bit VA space and 4-level page tables for 4K pages.
PCI:
- Add controllers before the specified head
irqchip driver for MIPS CPU:
- Replace magic 0x100 with IE_SW0
- Prepare for non-legacy IRQ domains
- Introduce IPI IRQ domain support
MAINTAINERS:
- Update email-id of Rahul Bedarkar
NET:
- sb1250-mac: Add missing MODULE_LICENSE()
CPUFREQ:
- Loongson2: drop set_cpus_allowed_ptr()
Misc:
- Disable Werror when W= is set
- Opt into HAVE_COPY_THREAD_TLS
- Enable GENERIC_CPU_AUTOPROBE
- Use common outgoing-CPU-notification code
- Remove dead define of ST_OFF
- Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
- Stengthen IPI IRQ domain sanity check
- Remove confusing else statement in __do_page_fault()
- Don't unnecessarily include kmalloc.h into <asm/cache.h>.
- Delete unused definition of SMP_CACHE_SHIFT.
- Delete redundant definition of SMP_CACHE_BYTES"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (39 commits)
MIPS: Sibyte: Fix Kconfig warning.
MIPS: Sibyte: Export symbol periph_rev to sb1250-mac network driver.
NET: sb1250-mac: Add missing MODULE_LICENSE()
MAINTAINERS: Update email-id of Rahul Bedarkar
MIPS: Remove confusing else statement in __do_page_fault()
MIPS: Stengthen IPI IRQ domain sanity check
MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support
irqchip: mips-cpu: Introduce IPI IRQ domain support
irqchip: mips-cpu: Prepare for non-legacy IRQ domains
irqchip: mips-cpu: Replace magic 0x100 with IE_SW0
MIPS: Remove CONFIG_ARCH_HAS_ILOG2_U{32,64}
MIPS: generic: Enable Root FS on NFS in generic_defconfig
MIPS: mach-rm: Remove recursive include of cpu-feature-overrides.h
MIPS: Opt into HAVE_COPY_THREAD_TLS
CPUFREQ: Loongson2: drop set_cpus_allowed_ptr()
MIPS: uasm: Remove needless ISA abstraction
MIPS: Remove dead define of ST_OFF
MIPS: Use common outgoing-CPU-notification code
MIPS: math-emu: Fix BC1EQZ and BC1NEZ condition handling
MIPS: r2-on-r6-emu: Clear BLTZALL and BGEZALL debugfs counters
...
|
|
There are several paths in vmxnet3, where settings changes cause the
adapter to be brought down and back up (vmxnet3_set_ringparam among
them). Should part of the reset operation fail, these paths call
vmxnet3_force_close, which enables all napi instances prior to calling
dev_close (with the expectation that vmxnet3_close will then properly
disable them again). However, vmxnet3_force_close neglects to clear
VMXNET3_STATE_BIT_QUIESCED prior to calling dev_close. As a result
vmxnet3_quiesce_dev (called from vmxnet3_close), returns early, and
leaves all the napi instances in a enabled state while the device itself
is closed. If a device in this state is activated again, napi_enable
will be called on already enabled napi_instances, leading to a BUG halt.
The fix is to simply enausre that the QUIESCED bit is cleared in
vmxnet3_force_close to allow quesence to be completed properly on close.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The revision enum values (eg EFX_REV_HUNT_A0) form part of our API,
and are included in ethtool. If these are inconsistent then ethtool
will print garbage for a register dump (ethtool -d).
Fixes: 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing endianness conversions to a debug statement printing
the USB device-descriptor idVendor and idProduct fields during probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing endianness conversion when using the USB device-descriptor
bcdDevice field to construct a firmware file name.
Fixes: 8ef80aef118e ("[IRDA]: irda-usb.c: STIR421x cleanups")
Cc: stable <stable@vger.kernel.org> # 2.6.18
Cc: Nick Fedchik <nfedchik@atlantic-link.com.ua>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add default case to switch in order to avoid any chance of using an
uninitialized variable _low_, in case s->type does not match any of
the listed case values.
Addresses-Coverity-ID: 1398130
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new Kconfig option to enable/disable the extra warnings
from the vblank evade code. For now we'll keep the warning
about an actually missed vblank always enabled as that can have
an actual user visible impact. But if we miss the deadline
othrwise there's no real need to bother the user with that.
We'll want these warnings enabled during development however
so that we can catch regressions.
Based on the reports it looks like this is still very easy
to hit on SKL, so we have more work ahead of us to optimize
the crtiical section further.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: e1edbd44e23b ("drm/i915: Complain if we take too long under vblank evasion.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Quite a few patches, but not much code changed:
- Fixes regression from atomic when only the source rect of a plane
changes (ie. xrandr --right-of)
- Fixes another issue where atomic changed behaviour underneath us,
potentially causing laggy cursor position updates
- Fixes for a bunch of races in thermal code, which lead to random
lockups for a lot of users
* 'linux-4.12' of git://github.com/skeggsb/linux:
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
drm/nouveau/tmr: handle races with hw when updating the next alarm time
drm/nouveau/tmr: ack interrupt before processing alarms
drm/nouveau/core: fix static checker warning
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
drm/nouveau/kms/nv50: fix source-rect-only plane updates
drm/nouveau/kms/nv50: remove pointless argument to window atomic_check_acquire()
|
|
into drm-next
Fixes for 4.12. This is a bit bigger than usual since it's 3 weeks
worth of fixes and most of these changes are for vega10 which is
new for 4.12 and still in a fair amount of flux. It looks like
you missed my last pull request, so those patches are included here
as well. Highlights:
- Lots of vega10 fixes
- Fix interruptable wait mixup
- Fan control method fixes
- Misc display fixes for radeon and amdgpu
- Misc bug fixes
* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (132 commits)
drm/amd/powerplay: refine pwm1_enable callback functions for CI.
drm/amd/powerplay: refine pwm1_enable callback functions for vi.
drm/amd/powerplay: refine pwm1_enable callback functions for Vega10.
drm/amdgpu: refine amdgpu pwm1_enable sysfs interface.
drm/amdgpu: add amd fan ctrl mode enums.
drm/amd/powerplay: add more smu message on Vega10.
drm/amdgpu: fix dependency issue
drm/amd: fix init order of sched job
drm/amdgpu: add some additional vega10 pci ids
drm/amdgpu/soc15: use atomfirmware for setting bios scratch for reset
drm/amdgpu/atomfirmware: add function to update engine hang status
drm/radeon: only warn once in radeon_ttm_bo_destroy if va list not empty
drm/amdgpu: fix mutex list null pointer reference
drm/amd/powerplay: fix bug sclk/mclk level can't be set on vega10.
drm/amd/powerplay: Setup sw CTF to allow graceful exit when temperature exceeds maximum.
drm/amd/powerplay: delete dead code in powerplay.
drm/amdgpu: Use less generic enum definitions
drm/amdgpu/gfx9: derive tile pipes from golden settings
drm/amdgpu/gfx: drop max_gs_waves_per_vgt
drm/amd/powerplay: disable engine spread spectrum feature on Vega10.
...
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-next
Core Changes:
- Add quirk for LGD 764 panel to default 10bpc (Mario)
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
* tag 'drm-misc-next-fixes-2017-05-05' of git://anongit.freedesktop.org/git/drm-misc:
drm/edid: Add 10 bpc quirk for LGD 764 panel in HP zBook 17 G2
|
|
The API convention makes it that a given MDIO bus reset should be able
to access PHY devices in its reset() callback and perform additional
MDIO accesses in order to bring the bus and PHYs in a working state.
Commit 69226896ad63 ("mdio_bus: Issue GPIO RESET to PHYs.") broke that
contract by first calling bus->reset() and then release all PHYs from
reset using their shared GPIO line, so restore the expected
functionality here.
Fixes: 69226896ad63 ("mdio_bus: Issue GPIO RESET to PHYs.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error status err is initialized as zero and then being checked
several times to see if it is less than zero even when it has not
been updated. It may seem that the err should be assigned to the
return code of the call to the various *offload_en_set calls and
then we check for failure, however, these functions are void and
never actually return any status.
Since these error checks are redundant we can remove these
as well as err and the error exit label err_exit.
Detected by CoverityScan, CID#1398313 and CID#1398306 ("Logically
dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bumping up the version as couple of fixes added after 5.3.65
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently driver returns error on speed configurations
for 83xx adapter's non XGBE ports, due to this link doesn't
come up on the ports using 1000Base-T as a connector with
autoneg disabled. This patch fixes this with initializing
appropriate port type based on queried module/connector
types from hardware before any speed/autoneg configuration.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unavoidable crashes in netfront_resume() and netback_changed() after a
previous fail in talk_to_netback() (e.g. when we fail to read MAC from
xenstore) were discovered. The failure path in talk_to_netback() does
unregister/free for netdev but we don't reset drvdata and we try accessing
it after resume.
Fix the bug by removing the whole xen device completely with
device_unregister(), this guarantees we won't have any calls into netfront
after a failure.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-7 warns about 'const SIMPLE_DEV_PM_OPS', as that macro already contains
a 'const' keyword:
drivers/input/keyboard/cros_ec_keyb.c:663:14: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
static const SIMPLE_DEV_PM_OPS(cros_ec_keyb_pm_ops, NULL, cros_ec_keyb_resume);
This removes the extra one.
Fixes: 6af6dc2d2aa6 ("input: Add ChromeOS EC keyboard driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
These were ineffective due to touching the list without the alarm lock,
but should no longer be required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
The idea here was to avoid having to "manually" program the HW if there's
a new earliest alarm. This was lazy and bad, as it leads to loads of fun
races between inter-related callers (ie. therm).
Turns out, it's not so difficult after all. Go figure ;)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
At least therm/fantog "attempts" to work around this issue, which could
lead to corruption of the pending alarm list.
Fix it properly by not updating the timestamp without the lock held, or
trying to add an already pending alarm to the pending alarm list....
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
If the time to the next alarm is short enough, we could race with HW and
end up with an ~4 second delay until it triggers.
Fix this by checking again after we update HW.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
Fixes a race where we can miss an alarm that triggers while we're already
processing previous alarms.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
|
|
object->engine cannot be NULL, it's either valid, or an error pointer.
This particular condition shouldn't actually be possible, but just in
case, we'll keep it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This reg has moved on Pascal, and causes a bus fault.
We never use the value anyway, so just remove the read.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The DRM core used to only call prepare_fb/cleanup_fb() when a plane's
framebuffer changed, which achieved the desired effect.
It's apparently now up to the driver to decide on its own.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.11+]
|
|
This "optimisation" (which was originally meant to skip updating cursor
settings in the core channel on position-only updates) turned out to be
pointless in the final design of the code before it was merged.
Remove it completely, as it breaks other cases.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org [4.10+]
|
