| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the device, different VRFs (routing tables) are represented using
different virtual routers (VRs) and thus the kernel's table IDs are
mapped to VR IDs.
Allow internal users of the IP router to query the VR ID based on a
kernel table ID.
This is needed - for example - when configuring the underlay VR where
VxLAN encapsulated packets will undergo an L3 lookup. In this case, the
kernel's table ID is derived from the VxLAN device's configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an NVE tunnel with an IP underlay (e.g., VxLAN) is configured the
local route to the tunnel's source IP needs to be promoted to perform
NVE decapsulation.
Expose an API in the unicast IP router to promote / demote local routes.
The case where a local route is configured after the creation of the NVE
tunnel will be handled in a subsequent patch in the set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current APIs only allow looking for a FID and creating it in case it
does not exist.
With VxLAN, in case the bridge to which the VxLAN device was enslaved
does not already have a corresponding FID, then it means that something
went wrong that we need to be aware of.
Add an API to look up a FID, but without creating it in order to catch
above-mentioned situation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the device, the VNI and the list of remote VTEPs a packet should be
flooded to is a property of the filtering identifier (FID).
During encapsulation, the VNI is taken from the FID the packet was
classified to. During decapsulation, the overlay packet is injected into
a bridge and classified to a FID based on the VNI it came with.
Allow NVE configuration for a FID. Currently, this is only supported
with 802.1D FIDs which are used for VLAN-unaware bridges. However, NVE
configuration is going to be supported with 802.1Q FIDs which is why the
related fields are placed in the common FID struct.
Since the device requires a 1:1 mapping between FID and VNI, the driver
maintains a hashtable keyed by VNI and checks if the VNI is already
associated with an existing FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we fail when user specify a non-zero chain, this patch adds the
support for it and tc priorities. To get to a new chain, use the tc
goto action.
Currently we support a fixed prio range 1-16, and chain range 0-3.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When adding a vxlan tc rule, and a neighbour isn't available, we
don't insert any rule to hardware. Once we enable offloading flows
with multiple priorities, a packet that should have matched this rule
will continue in hardware pipeline and might match a wrong one.
This is unlike in tc software path where it will be matched and
forwarded to the vxlan device (which will cause a ARP lookup
eventually) and stop processing further tc filters.
To address that, when when a neighbour isn't available (EAGAIN from
attach_encap), or gets deleted, change the original action to be a
forward to slow path instead. Neighbour update will restore the original
action once the neighbour becomes available. This will be done atomically
so at any given time we will have a the correct match.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
A pre-step for the tc offloads code to use this when a neigh is
not available for encap rules.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The code for adding/deleting fdb flow is repeated when
user-space does flow add/del and when we add/del from
the neigh update path - unify them to avoid the duplication.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When replacing a tc flower rule, flower first requests to add the
new rule (new action), then deletes the old one.
But currently when asked to add a new tc flower flow, we append the
actions (and counters to it).
This can result in a fte with two flow counters or conflicting
actions (drop and encap action) which firmware complains/errs
about and isn't achieving what the user aimed for.
Instead, insert the flow using the new no-append flag which will add a
new HW rule, the old flow and rule will be deleted later by flower
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanmox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If no-append flag is set, we will add a new FTE, instead of appending
the actions of the inserted rule when the same match already exists.
While here, move the has_flow_tag boolean indicator to be a flag too.
This patch doesn't change any functionality.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanmox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
A chain is a group of priorities, so use the fdb parallel
sub namespaces to implement chains, and a flow table for each
priority in them.
Because these namespaces are parallel and in series to the slow path
fdb, the chains aren't connected to one another (but to the slow path),
and one must use a explicit goto action to reach a different chain.
Flow tables for the priorities will be created on demand and destroyed
once not used.
The Firmware has four pools of tables for sizes S/XS/M/L (4k, 64k, 1m, 4m).
We maintain ghost copies of the pools occupancy.
When a new table is to be created, we scan the pools from large to small
and find the 1st table size which can be now created. When a table is
destroyed, we update the relevant pool.
Multi chain/prio isn't enabled yet by this patch, for now all flows
will use the default chain 0, and prio 1.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Be symmetric with the e-switch API to add rules which has a
specific function to add fwd rules which are used as part of
vport mirroring.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Towards supporting multi-chains and priorities, split the FDB fast path
to multiple namespaces (sub namespaces), each with multiple priorities.
This patch adds a new flow steering type, FS_TYPE_PRIO_CHAINS, which is
like current FS_TYPE_PRIO, but may contain only namespaces, and those
will be in parallel to one another in terms of managing of the flow
tables connections inside them. Meaning, while searching for the next
or previous flow table to connect for a new table inside such namespace
we skip the parallel namespaces in the same level under the
FS_TYPE_PRIO_CHAINS prio we originated from.
We use this new type for splitting the fast path prio into multiple
parallel namespaces, each containing normal prios.
The prios inside them (and their tables) will be connected to one
another, but not from one parallel namespace to another, instead the
last prio in each namespace will be connected to the next prio in
the containing FDB namespace, which is the slow path prio.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move to have clear separation on the code path to add nic vs e-switch
flows. While here we break the code that deals with adding offloaded
TC tool to few smaller stages, each on helper function.
Besides getting us simpler and readable code, these are pre-steps
for being able to have two HW flows serving one SW TC flow for some
e-switch use cases.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Refactor the flow add utility functions to return err code instead of rule
pointers. This will allow for simpler logic when one tc rule is
duplicated to two HW rules in downstream patches.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, when a flow rule is created using the FS core layer, the caller
has to pass the entire flow counter object and not just the counter HW
handle (ID). This requires both the FS core and the caller to have
knowledge about the inner implementation of the FS layer flow counters
cache and limits the possible users.
Move to use the counter ID across the place when dealing with flows.
Doing this decoupling, now can we privatize the inner implementation
of the flow counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There's no real reason for the e-switch logic to manage the creation of
counters for offloaded flows. The API already has the directive for the
caller to denote they want to attach a counter to the created flow.
As such, we go and move the management of flow counters to the mlx5e
tc offload logic. This also lets us remove an inelegant interface where
the FS layer had to provide a way to retrieve a counter from a flow rule.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into net-next
mlx5 updates for both net-next and rdma-next
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux: (21 commits)
net/mlx5: Expose DC scatter to CQE capability bit
net/mlx5: Update mlx5_ifc with DEVX UID bits
net/mlx5: Set uid as part of DCT commands
net/mlx5: Set uid as part of SRQ commands
net/mlx5: Set uid as part of SQ commands
net/mlx5: Set uid as part of RQ commands
net/mlx5: Set uid as part of QP commands
net/mlx5: Set uid as part of CQ commands
net/mlx5: Rename incorrect naming in IFC file
net/mlx5: Export packet reformat alloc/dealloc functions
net/mlx5: Pass a namespace for packet reformat ID allocation
net/mlx5: Expose new packet reformat capabilities
{net, RDMA}/mlx5: Rename encap to reformat packet
net/mlx5: Move header encap type to IFC header file
net/mlx5: Break encap/decap into two separated flow table creation flags
net/mlx5: Add support for more namespaces when allocating modify header
net/mlx5: Export modify header alloc/dealloc functions
net/mlx5: Add proper NIC TX steering flow tables support
net/mlx5: Cleanup flow namespace getter switch logic
net/mlx5: Add memic command opcode to command checker
...
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Code completion, remove obsolete code
Add watchdog methods
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add link establishment methods
Add auto negotiation methods
Add read MAC address method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add code for NVM support and get MAC address, complete probe
method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add code for hardware initialization and reset
Add code for semaphore handling
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for allocating, configuring, and freeing Tx/Rx ring
resources. With these changes in place the descriptor queues are in a
state where they are ready to transmit or receive if provided buffers.
This also adds the transmit and receive fastpath and interrupt handlers.
With this code in place the network device is now able to send and receive
frames over the network interface using a single queue.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch set adds interrupt support for the igc interfaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that we have the ability to configure the basic settings on the device
we can start allocating and configuring a netdev for the interface.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the basic defines and structures needed by the PF for
operation. With this it is possible to bring up the interface,
but without being able to configure any of the filters on
the interface itself.
Add skeleton for a function pointers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the beginning framework onto which I am going to add
the igc driver which supports the Intel(R) I225-LM/I225-V 2.5G
Ethernet Controller.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Stephen writes:
"clk fixes for v4.19-rc8
One fix for the Allwinner A10 SoC's audio PLL that wasn't properly
set and generating noise."
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi-ng: sun4i: Set VCO and PLL bias current to lowest setting
|
|
Program translation stage checks that program can be offloaded to
the netdev which was passed during the load (bpf_attr->prog_ifindex).
After program sharing was introduced, however, the netdev on which
program is loaded can theoretically be different, and therefore
we should recheck the program size and max stack size at load time.
This was found by code inspection, AFAIK today all vNICs have
identical caps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Atomic operations on the NFP are currently always in big endian.
The driver keeps track of regions of memory storing atomic values
and byte swaps them accordingly. There are corner cases where
the map values may be initialized before the driver knows they
are used as atomic counters. This can happen either when the
datapath is performing the update and the stack contents are
unknown or when map is updated before the program which will
use it for atomic values is loaded.
To avoid situation where user initializes the value to 0 1 2 3
and then after loading a program which uses the word as an atomic
counter starts reading 3 2 1 0 - only allow atomic counters to be
initialized to endian-neutral values.
For updates from the datapath the stack information may not be
as precise, so just allow initializing such values to 0.
Example code which would break:
struct bpf_map_def SEC("maps") rxcnt = {
.type = BPF_MAP_TYPE_HASH,
.key_size = sizeof(__u32),
.value_size = sizeof(__u64),
.max_entries = 1,
};
int xdp_prog1()
{
__u64 nonzeroval = 3;
__u32 key = 0;
__u64 *value;
value = bpf_map_lookup_elem(&rxcnt, &key);
if (!value)
bpf_map_update_elem(&rxcnt, &key, &nonzeroval, BPF_ANY);
else
__sync_fetch_and_add(value, 1);
return XDP_PASS;
}
$ offload bpftool map dump
key: 00 00 00 00 value: 00 00 00 03 00 00 00 00
should be:
$ offload bpftool map dump
key: 00 00 00 00 value: 03 00 00 00 00 00 00 00
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When sending a big fragment using multiple buffer descriptor,
hns3 does one maping, but do multiple unmapping when tx is done,
which may cause unmapping problem.
To fix it, this patch makes sure the value of desc_cb.length of
the non-first bd is zero. If desc_cb.length is zero, we do not
unmap the buffer.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To keep symmetrical, this patch renames hns_nic_dma_unmap to
hns3_clear_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch unifies big tx fragment handling for tso and non-tso
case.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To solve the L3 checksum error problem which happens when driver
does not clear L3 checksum, DMA map should be done after calling
skb_cow_head.
This patch moves DMA map into hns3_fill_desc to ensure that DMA
map is done after calling skb_cow_head.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes hns3_fill_desc_tso in preparation for
fixing some desc filling bug, because for tso or non-tso
case, we will use the unified hns3_fill_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newly added link modes are required to be added
during setting link modes. If the new link mode
is not available during qed_set_link, it may cause
link getting down due to empty supported capability,
being passed to MFW, after setting autoneg off/on
with current/supported speed.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set link mode after checking available "supported" link caps
of the port.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HSI.
Added transceiver modes with different speed and media type,
speed capability and supported board types in HSI, which
will be utilizing to display correct specification of link
modes and speed type.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Align the use of local PTT to propagate through the qed_mcp* API's.
Global ptt should not be used.
Register access should be done through layers. Register address is
mapped into a PTT, PF translation table. Several interface functions
require a PTT to direct read/write into register. There is a pool of
PTT maintained, and several PTT are used simultaneously to access
device registers in different flows. Same PTT should not be used in
flows that can run concurrently.
To avoid running out of PTT resources, too many PTT should not be
acquired without releasing them. Every PF has a global PTT, which is
used throughout the life of PF, in most important flows for register
access. Generic functions acquire the PTT locally and release after
the use. This patch aligns the use of Global PTT and Local PTT
accordingly.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c:282:5: warning:
symbol 'aq_fw2x_update_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David writes:
"Sparc fixes
1) Revert the %pOF change, it causes regressions.
2) Wire up io_pgetevents().
3) Fix perf events on single-PCR sparc64 cpus.
4) Do proper perf event throttling like arm and x86."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
Revert "sparc: Convert to using %pOFn instead of device_node.name"
sparc64: Set %l4 properly on trap return after handling signals.
sparc64: Make proc_id signed.
sparc: Throttle perf events properly.
sparc: Fix single-pcr perf event counter management.
sparc: Wire up io_pgetevents system call.
sunvdc: Remove VLA usage
|
|
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucma.c:1686 ucma_write() warn: potential
spectre issue 'ucma_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucm.c:1127 ib_ucm_write() warn: potential
spectre issue 'ucm_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
HDMI Forum VSDB YCBCR420 deep color capability bits are 2:0. Correct
definitions in the header for the mask to work correctly.
Fixes: e6a9a2c3dc43 ("drm/edid: parse ycbcr 420 deep color information")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107893
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538776335-12569-1-git-send-email-clinton.a.taylor@intel.com
|
|
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Previously when populating the set ipv6 address action, we incorrectly
made use of pedit's key index to determine which 32bit word should be
set. We now calculate which word has been selected based on the offset
provided by the pedit action.
Fixes: 354b82bb320e ("nfp: add set ipv6 source and destination address")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
