summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2019-02-20s390/zcrypt: fix specification exception on z196 during ap probeHarald Freudenberger1-1/+2
commit 8f9aca0c45322a807a343fc32f95f2500f83b9ae upstream. The older machines don't have the QCI instruction available. With support for up to 256 crypto cards the probing of each card has been extended to check card ids from 0 up to 255. For machines with QCI support there is a filter limiting the range of probed cards. The older machines (z196 and older) don't have this filter and so since support for 256 cards is in the driver all cards are probed. However, these machines also require to have the card id fit into 6 bits. Exceeding this limit results in a specification exception which happens on every kernel startup even when there is no crypto configured and used at all. This fix limits the range of probed crypto cards to 64 if there is no QCI instruction available to obey to the older ap architecture and so fixes the specification exceptions on z196 machines. Cc: stable@vger.kernel.org # v4.17+ Fixes: af4a72276d49 ("s390/zcrypt: Support up to 256 crypto adapters.") Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20Input: elantech - enable 3rd button support on Fujitsu CELSIUS H780Matti Kurkela1-0/+9
commit e8b22d0a329f0fb5c7ef95406872d268f01ee3b1 upstream. Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech touchpad, but the driver needs to be told so to enable the middle touchpad button. The elantech_dmi_force_crc_enabled quirk was not necessary with the H780. Also document the fw_version and caps values detected for both H760 and H780 models. Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20Input: bma150 - register input device after setting private dataJonathan Bakker1-4/+5
commit 90cc55f067f6ca0e64e5e52883ece47d8af7b67b upstream. Otherwise we introduce a race condition where userspace can request input before we're ready leading to null pointer dereference such as input: bma150 as /devices/platform/i2c-gpio-2/i2c-5/5-0038/input/input3 Unable to handle kernel NULL pointer dereference at virtual address 00000018 pgd = (ptrval) [00000018] *pgd=55dac831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: bma150 input_polldev [last unloaded: bma150] CPU: 0 PID: 2870 Comm: accelerometer Not tainted 5.0.0-rc3-dirty #46 Hardware name: Samsung S5PC110/S5PV210-based board PC is at input_event+0x8/0x60 LR is at bma150_report_xyz+0x9c/0xe0 [bma150] pc : [<80450f70>] lr : [<7f0a614c>] psr: 800d0013 sp : a4c1fd78 ip : 00000081 fp : 00020000 r10: 00000000 r9 : a5e2944c r8 : a7455000 r7 : 00000016 r6 : 00000101 r5 : a7617940 r4 : 80909048 r3 : fffffff2 r2 : 00000000 r1 : 00000003 r0 : 00000000 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 54e34019 DAC: 00000051 Process accelerometer (pid: 2870, stack limit = 0x(ptrval)) Stackck: (0xa4c1fd78 to 0xa4c20000) fd60: fffffff3 fc813f6c fd80: 40410581 d7530ce3 a5e2817c a7617f00 a5e29404 a5e2817c 00000000 7f008324 fda0: a5e28000 8044f59c a5fdd9d0 a5e2945c a46a4a00 a5e29668 a7455000 80454f10 fdc0: 80909048 a5e29668 a5fdd9d0 a46a4a00 806316d0 00000000 a46a4a00 801df5f0 fde0: 00000000 d7530ce3 a4c1fec0 a46a4a00 00000000 a5fdd9d0 a46a4a08 801df53c fe00: 00000000 801d74bc a4c1fec0 00000000 a4c1ff70 00000000 a7038da8 00000000 fe20: a46a4a00 801e91fc a411bbe0 801f2e88 00000004 00000000 80909048 00000041 fe40: 00000000 00020000 00000000 dead4ead a6a88da0 00000000 ffffe000 806fcae8 fe60: a4c1fec8 00000000 80909048 00000002 a5fdd9d0 a7660110 a411bab0 00000001 fe80: dead4ead ffffffff ffffffff a4c1fe8c a4c1fe8c d7530ce3 20000013 80909048 fea0: 80909048 a4c1ff70 00000001 fffff000 a4c1e000 00000005 00026038 801eabd8 fec0: a7660110 a411bab0 b9394901 00000006 a696201b 76fb3000 00000000 a7039720 fee0: a5fdd9d0 00000101 00000002 00000096 00000000 00000000 00000000 a4c1ff00 ff00: a6b310f4 805cb174 a6b310f4 00000010 00000fe0 00000010 a4c1e000 d7530ce3 ff20: 00000003 a5f41400 a5f41424 00000000 a6962000 00000000 00000003 00000002 ff40: ffffff9c 000a0000 80909048 d7530ce3 a6962000 00000003 80909048 ffffff9c ff60: a6962000 801d890c 00000000 00000000 00020000 a7590000 00000004 00000100 ff80: 00000001 d7530ce3 000288b8 00026320 000288b8 00000005 80101204 a4c1e000 ffa0: 00000005 80101000 000288b8 00026320 000288b8 000a0000 00000000 00000000 ffc0: 000288b8 00026320 000288b8 00000005 7eef3bac 000264e8 00028ad8 00026038 ffe0: 00000005 7eef3300 76f76e91 76f78546 800d0030 000288b8 00000000 00000000 [<80450f70>] (input_event) from [<a5e2817c>] (0xa5e2817c) Code: e1a08148 eaffffa8 e351001f 812fff1e (e590c018) ---[ end trace 1c691ee85f2ff243 ]--- Signed-off-by: Jonathan Bakker <xc-racer2@live.ca> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20mmc: block: handle complete_work on separate workqueueZachary Hays1-1/+9
commit dcf6e2e38a1c7ccbc535de5e1d9b14998847499d upstream. The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set. This generates a rescuer thread for that queue that will trigger when the CPU is under heavy load and collect the uncompleted work. In the case of mmc, this creates the possibility of a deadlock when there are multiple partitions on the device as other blk-mq work is also run on the same queue. For example: - worker 0 claims the mmc host to work on partition 1 - worker 1 attempts to claim the host for partition 2 but has to wait for worker 0 to finish - worker 0 schedules complete_work to release the host - rescuer thread is triggered after time-out and collects the dangling work - rescuer thread attempts to complete the work in order starting with claim host - the task to release host is now blocked by a task to claim it and will never be called The above results in multiple hung tasks that lead to failures to mount partitions. Handling complete_work on a separate workqueue avoids this by keeping the work completion tasks separate from the other blk-mq work. This allows the host to be released without getting blocked by other tasks attempting to claim the host. Signed-off-by: Zachary Hays <zhays@lexmark.com> Fixes: 81196976ed94 ("mmc: block: Add blk-mq support") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20mmc: sunxi: Filter out unsupported modes declared in the device treeChen-Yu Tsai1-0/+15
commit d6f11e7d91f2ac85f66194fe3ef8789b49901d64 upstream. The MMC device tree bindings include properties used to signal various signalling speed modes. Until now the sunxi driver was accepting them without any further filtering, while the sunxi device trees were not actually using them. Since some of the H5 boards can not run at higher speed modes stably, we are resorting to declaring the higher speed modes per-board. Regardless, having boards declare modes and blindly following them, even without proper support in the driver, is generally a bad thing. Filter out all unsupported modes from the capabilities mask after the device tree properties have been parsed. Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISKMauro Ciancio1-0/+1
commit 7ad222b3aed350adfc27ee7eec4587ffe55dfdce upstream. This adds ELAN0617 to the ACPI table to support Elan touchpad found in Lenovo V330-15ISK. Signed-off-by: Mauro Ciancio <mauro@acadeu.com> Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20Revert "Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G"Dmitry Torokhov1-1/+0
commit f420c54e4b12c1361c6ed313002ee7bd7ac58362 upstream. This reverts commit 7db54c89f0b30a101584e09d3729144e6170059d as it breaks Acer Aspire V-371 and other devices. According to Elan: "Acer Aspire F5-573G is MS Precision touchpad which should use hid multitouch driver. ELAN0501 should not be added in elan_i2c." Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202503 Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20gpio: mxc: move gpio noirq suspend/resume to syscore phaseAnson Huang1-17/+24
commit 1a5287a3dbc34cd0c02c8f64c9131bd23cdfe2bb upstream. During noirq suspend/resume phase, GPIO irq could arrive and its registers like IMR will be changed by irq handle process, to make the GPIO registers exactly when it is powered ON after resume, move the GPIO noirq suspend/resume callback to syscore suspend/resume phase, local irq is disabled at this phase so GPIO registers are atomic. Fixes: c19fdaeea0aa ("gpio: mxc: add power management support") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Martin Hundebøll <martin@geanix.com> Cc: <stable@vger.kernel.org> # 4.19.x+ Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/nouveau/falcon: avoid touching registers if engine is offIlia Mirkin1-2/+5
[ Upstream commit a5176a4cb85bb6213daadf691097cf411da35df2 ] Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108980 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/nouveau: Don't disable polling in fallback modeTakashi Iwai1-3/+4
[ Upstream commit 118780066e30c34de3d9349710b51780bfa0ba83 ] When a fan is controlled via linear fallback without cstate, we shouldn't stop polling. Otherwise it won't be adjusted again and keeps running at an initial crazy pace. Fixes: 800efb4c2857 ("drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios") Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103356 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107447 Reported-by: Thomas Blume <thomas.blume@suse.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Martin Peres <martin.peres@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/amdgpu: set WRITE_BURST_LENGTH to 64B to workaround SDMA1 hangJim Qu1-1/+2
[ Upstream commit 0c6c8125582714e1fd3544983eba3d750db0f5b8 ] effect asics: VEGA10 and VEGA12 Signed-off-by: Jim Qu <Jim.Qu@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20nvme: pad fake subsys NQN vid and ssvid with zerosKeith Busch1-1/+1
[ Upstream commit 3da584f57133e51aeb84aaefae5e3d69531a1e4f ] We need to preserve the leading zeros in the vid and ssvid when generating a unique NQN. Truncating these may lead to naming collisions. Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20nvme-multipath: zero out ANA log bufferHannes Reinecke1-0/+2
[ Upstream commit c7055fd15ff46d92eb0dd1c16a4fe010d58224c8 ] When nvme_init_identify() fails the ANA log buffer is deallocated but _not_ set to NULL. This can cause double free oops when this controller is deleted without ever being reconnected. Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20nvme-pci: fix out of bounds access in nvme_cqe_pendingHongbo Yao1-1/+3
[ Upstream commit dcca1662727220d18fa351097ddff33f95f516c5 ] There is an out of bounds array access in nvme_cqe_peding(). When enable irq_thread for nvme interrupt, there is racing between the nvmeq->cq_head updating and reading. nvmeq->cq_head is updated in nvme_update_cq_head(), if nvmeq->cq_head equals nvmeq->q_depth and before its value set to zero, nvme_cqe_pending() uses its value as an array index, the index will be out of bounds. Signed-off-by: Hongbo Yao <yaohongbo@huawei.com> [hch: slight coding style update] Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20nvme-pci: use the same attributes when freeing host_mem_desc_bufs.Liviu Dudau1-4/+6
[ Upstream commit cc667f6d5de023ee131e96bb88e5cddca23272bd ] When using HMB the PCIe host driver allocates host_mem_desc_bufs using dma_alloc_attrs() but frees them using dma_free_coherent(). Use the correct dma_free_attrs() function to free the buffers. Signed-off-by: Liviu Dudau <liviu@dudau.co.uk> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: fix output H/V syncsTomi Valkeinen1-1/+5
[ Upstream commit 7923e09c7a766e2d58de7fc395bb84c18e5bc625 ] The H and V syncs of the DP output are always set to active high. This patch fixes the syncs by configuring them according to the videomode. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-7-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: reject modes which require too much BWTomi Valkeinen1-0/+10
[ Upstream commit 51b9e62eb6950c762162ab7eb8390990179be067 ] The current driver accepts any videomode with pclk < 154MHz. This is not correct, as with 1 lane and/or 1.62Mbps speed not all videomodes can be supported. Add code to reject modes that require more bandwidth that is available. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-6-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: fix initial DP0/1_SRCCTRL valueTomi Valkeinen1-6/+5
[ Upstream commit 9a63bd6fe1b5590ffa42ae2ed22ee21363293e31 ] Initially DP0_SRCCTRL is set to a static value which includes DP0_SRCCTRL_LANES_2 and DP0_SRCCTRL_BW27, even when only 1 lane of 1.62Gbps speed is used. DP1_SRCCTRL is configured to a magic number. This patch changes the configuration as follows: Configure DP0_SRCCTRL by using tc_srcctrl() which provides the correct value. DP1_SRCCTRL needs two bits to be set to the same value as DP0_SRCCTRL: SSCG and BW27. All other bits can be zero. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-5-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: fix single lane configurationTomi Valkeinen1-2/+8
[ Upstream commit 4d9d54a730434cc068dd3515ba6116697196f77b ] PHY_2LANE bit is always set in DP_PHY_CTRL, breaking 1 lane use. Set PHY_2LANE only when 2 lanes are used. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-4-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: add defines for DP1_SRCCTRL & PHY_2LANETomi Valkeinen1-3/+7
[ Upstream commit adf4109896bbee27fd2ac3b48d22d6a0062fe517 ] DP1_SRCCTRL register and PHY_2LANE field did not have matching defines. Add these. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-3-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/bridge: tc358767: add bus flagsTomi Valkeinen1-0/+4
[ Upstream commit 4842379cbe6e851de914a7132f76f4e200b9a98b ] tc358767 driver does not set DRM bus_flags, even if it does configures the polarity settings into its registers. This means that the DPI source can't configure the polarities correctly. Add sync flags accordingly. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190103115954.12785-2-tomi.valkeinen@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20cpufreq: check if policy is inactive early in __cpufreq_get()Sudeep Holla1-8/+4
[ Upstream commit 2f66196208c98b3d1b4294edffb2c5a8197be899 ] cpuinfo_cur_freq gets current CPU frequency as detected by hardware while scaling_cur_freq last known CPU frequency. Some platforms may not allow checking the CPU frequency of an offline CPU or the associated resources may have been released via cpufreq_exit when the CPU gets offlined, in which case the policy would have been invalidated already. If we attempt to get current frequency from the hardware, it may result in hang or crash. For example on Juno, I see: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000188 [0000000000000188] pgd=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: CPU: 5 PID: 4202 Comm: cat Not tainted 4.20.0-08251-ga0f2c0318a15-dirty #87 Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform pstate: 40000005 (nZcv daif -PAN -UAO) pc : scmi_cpufreq_get_rate+0x34/0xb0 lr : scmi_cpufreq_get_rate+0x34/0xb0 Call trace: scmi_cpufreq_get_rate+0x34/0xb0 __cpufreq_get+0x34/0xc0 show_cpuinfo_cur_freq+0x24/0x78 show+0x40/0x60 sysfs_kf_seq_show+0xc0/0x148 kernfs_seq_show+0x44/0x50 seq_read+0xd4/0x480 kernfs_fop_read+0x15c/0x208 __vfs_read+0x60/0x188 vfs_read+0x94/0x150 ksys_read+0x6c/0xd8 __arm64_sys_read+0x24/0x30 el0_svc_common+0x78/0x100 el0_svc_handler+0x38/0x78 el0_svc+0x8/0xc ---[ end trace 3d1024e58f77f6b2 ]--- So fix the issue by checking if the policy is invalid early in __cpufreq_get before attempting to get the current frequency. Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20ACPI: NUMA: Use correct type for printing addresses on i386-PAEChao Fan1-3/+3
[ Upstream commit b9ced18acf68dffebe6888c7ec765a2b1db7a039 ] The addresses of NUMA nodes are not printed correctly on i386-PAE which is misleading. Here is a debian9-32bit with PAE in a QEMU guest having more than 4G of memory: qemu-system-i386 \ -hda /var/lib/libvirt/images/debian32.qcow2 \ -m 5G \ -enable-kvm \ -smp 10 \ -numa node,mem=512M,nodeid=0,cpus=0 \ -numa node,mem=512M,nodeid=1,cpus=1 \ -numa node,mem=512M,nodeid=2,cpus=2 \ -numa node,mem=512M,nodeid=3,cpus=3 \ -numa node,mem=512M,nodeid=4,cpus=4 \ -numa node,mem=512M,nodeid=5,cpus=5 \ -numa node,mem=512M,nodeid=6,cpus=6 \ -numa node,mem=512M,nodeid=7,cpus=7 \ -numa node,mem=512M,nodeid=8,cpus=8 \ -numa node,mem=512M,nodeid=9,cpus=9 \ -serial stdio Because of the wrong value type, it prints as below: [ 0.021049] ACPI: SRAT Memory (0x0 length 0xa0000) in proximity domain 0 enabled [ 0.021740] ACPI: SRAT Memory (0x100000 length 0x1ff00000) in proximity domain 0 enabled [ 0.022425] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 1 enabled [ 0.023092] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 2 enabled [ 0.023764] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 3 enabled [ 0.024431] ACPI: SRAT Memory (0x80000000 length 0x20000000) in proximity domain 4 enabled [ 0.025104] ACPI: SRAT Memory (0xa0000000 length 0x20000000) in proximity domain 5 enabled [ 0.025791] ACPI: SRAT Memory (0x0 length 0x20000000) in proximity domain 6 enabled [ 0.026412] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 7 enabled [ 0.027118] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 8 enabled [ 0.027802] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 9 enabled The upper half of the start address of the NUMA domains between 6 and 9 inclusive was cut, so the printed values are incorrect. Fix the value type, to get the correct values in the log as follows: [ 0.023698] ACPI: SRAT Memory (0x0 length 0xa0000) in proximity domain 0 enabled [ 0.024325] ACPI: SRAT Memory (0x100000 length 0x1ff00000) in proximity domain 0 enabled [ 0.024981] ACPI: SRAT Memory (0x20000000 length 0x20000000) in proximity domain 1 enabled [ 0.025659] ACPI: SRAT Memory (0x40000000 length 0x20000000) in proximity domain 2 enabled [ 0.026317] ACPI: SRAT Memory (0x60000000 length 0x20000000) in proximity domain 3 enabled [ 0.026980] ACPI: SRAT Memory (0x80000000 length 0x20000000) in proximity domain 4 enabled [ 0.027635] ACPI: SRAT Memory (0xa0000000 length 0x20000000) in proximity domain 5 enabled [ 0.028311] ACPI: SRAT Memory (0x100000000 length 0x20000000) in proximity domain 6 enabled [ 0.028985] ACPI: SRAT Memory (0x120000000 length 0x20000000) in proximity domain 7 enabled [ 0.029667] ACPI: SRAT Memory (0x140000000 length 0x20000000) in proximity domain 8 enabled [ 0.030334] ACPI: SRAT Memory (0x160000000 length 0x20000000) in proximity domain 9 enabled Signed-off-by: Chao Fan <fanc.fnst@cn.fujitsu.com> [ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20drm/amdgpu/sriov:Correct pfvf exchange logicEmily Deng2-5/+5
[ Upstream commit b8cf66182eddb22e9c7539821ed6eecdb4f86d1a ] The pfvf exchange need be in exclusive mode. And add pfvf exchange in gpu reset. Signed-off-by: Emily Deng <Emily.Deng@amd.com> Reviewed-By: Xiangliang Yu <Xiangliang.Yu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-20eeprom: at24: add support for 24c2048Adrian Bunk2-1/+4
[ Upstream commit 37cf28d3b5bca1b532a0b6aac722e7f2788a9294 ] Works with ST M24M02. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Sasha Levin <sashal@kernel.org>
2019-02-15drm/vmwgfx: Return error code from vmw_execbuf_copy_fence_userThomas Hellstrom1-1/+1
commit 728354c005c36eaf44b6e5552372b67e60d17f56 upstream. The function was unconditionally returning 0, and a caller would have to rely on the returned fence pointer being NULL to detect errors. However, the function vmw_execbuf_copy_fence_user() would expect a non-zero error code in that case and would BUG otherwise. So make sure we return a proper non-zero error code if the fence pointer returned is NULL. Cc: <stable@vger.kernel.org> Fixes: ae2a104058e2: ("vmwgfx: Implement fence objects") Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15drm/vmwgfx: Fix setting of dma masksThomas Hellstrom1-3/+6
commit 4cbfa1e6c09e98450aab3240e5119b0ab2c9795b upstream. Previously we set only the dma mask and not the coherent mask. Fix that. Also, for clarity, make sure both are initially set to 64 bits. Cc: <stable@vger.kernel.org> Fixes: 0d00c488f3de: ("drm/vmwgfx: Fix the driver for large dma addresses") Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15drm/i915: always return something on DDI clock selectionLucas De Marchi1-1/+1
commit 2a121030d4ee3f84f60c6f415f9c44bffbcde81d upstream. Even if we don't have the correct clock and get a warning, we should not skip the return. v2: improve commit message (from Joonas) Fixes: 1fa11ee2d9d0 ("drm/i915/icl: start adding the TBT pll") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Mika Kahola <mika.kahola@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190125222444.19926-3-lucas.demarchi@intel.com (cherry picked from commit 7a61a6dec3dfb9f2e8c39a337580a3c3036c5cdf) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15drm/amd/powerplay: Fix missing break in switchGustavo A. R. Silva1-0/+1
commit 2f10d823739680d2477ce34437e8a08a53117f40 upstream. Add missing break statement in order to prevent the code from falling through to the default case. The resoning for this is that pclk_vol_table is an automatic variable. So, it makes no sense to update it just before falling through to the default case and return -EINVAL. This bug was found thanks to the ongoing efforts to enabling -Wimplicit-fallthrough. Fixes: cd70f3d6e3fa ("drm/amd/powerplay: PP/DAL interface changes for dynamic clock switch") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15drm/modes: Prevent division by zero htotalTina Zhang1-1/+1
commit a2fcd5c84f7a7825e028381b10182439067aa90d upstream. This patch prevents division by zero htotal. In a follow-up mail Tina writes: > > How did you manage to get here with htotal == 0? This needs backtraces (or if > > this is just about static checkers, a mention of that). > > -Daniel > > In GVT-g, we are trying to enable a virtual display w/o setting timings for a pipe > (a.k.a htotal=0), then we met the following kernel panic: > > [ 32.832048] divide error: 0000 [#1] SMP PTI > [ 32.833614] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.18.0-rc4-sriov+ #33 > [ 32.834438] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.10.1-0-g8891697-dirty-20180511_165818-tinazhang-linux-1 04/01/2014 > [ 32.835901] RIP: 0010:drm_mode_hsync+0x1e/0x40 > [ 32.836004] Code: 31 c0 c3 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 8b 87 d8 00 00 00 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9 b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 f3 c3 66 > [ 32.836004] RSP: 0000:ffffc900000ebb90 EFLAGS: 00010206 > [ 32.836004] RAX: 0000000000000000 RBX: ffff88001c67c8a0 RCX: 0000000000000000 > [ 32.836004] RDX: 0000000000000000 RSI: ffff88001c67c000 RDI: ffff88001c67c8a0 > [ 32.836004] RBP: ffff88001c7d03a0 R08: ffff88001c67c8a0 R09: ffff88001c7d0330 > [ 32.836004] R10: ffffffff822c3a98 R11: 0000000000000001 R12: ffff88001c67c000 > [ 32.836004] R13: ffff88001c7d0370 R14: ffffffff8207eb78 R15: ffff88001c67c800 > [ 32.836004] FS: 0000000000000000(0000) GS:ffff88001da00000(0000) knlGS:0000000000000000 > [ 32.836004] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 32.836004] CR2: 0000000000000000 CR3: 000000000220a000 CR4: 00000000000006f0 > [ 32.836004] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > [ 32.836004] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 > [ 32.836004] Call Trace: > [ 32.836004] intel_mode_from_pipe_config+0x72/0x90 > [ 32.836004] intel_modeset_setup_hw_state+0x569/0xf90 > [ 32.836004] intel_modeset_init+0x905/0x1db0 > [ 32.836004] i915_driver_load+0xb8c/0x1120 > [ 32.836004] i915_pci_probe+0x4d/0xb0 > [ 32.836004] local_pci_probe+0x44/0xa0 > [ 32.836004] ? pci_assign_irq+0x27/0x130 > [ 32.836004] pci_device_probe+0x102/0x1c0 > [ 32.836004] driver_probe_device+0x2b8/0x480 > [ 32.836004] __driver_attach+0x109/0x110 > [ 32.836004] ? driver_probe_device+0x480/0x480 > [ 32.836004] bus_for_each_dev+0x67/0xc0 > [ 32.836004] ? klist_add_tail+0x3b/0x70 > [ 32.836004] bus_add_driver+0x1e8/0x260 > [ 32.836004] driver_register+0x5b/0xe0 > [ 32.836004] ? mipi_dsi_bus_init+0x11/0x11 > [ 32.836004] do_one_initcall+0x4d/0x1eb > [ 32.836004] kernel_init_freeable+0x197/0x237 > [ 32.836004] ? rest_init+0xd0/0xd0 > [ 32.836004] kernel_init+0xa/0x110 > [ 32.836004] ret_from_fork+0x35/0x40 > [ 32.836004] Modules linked in: > [ 32.859183] ---[ end trace 525608b0ed0e8665 ]--- > [ 32.859722] RIP: 0010:drm_mode_hsync+0x1e/0x40 > [ 32.860287] Code: 31 c0 c3 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 8b 87 d8 00 00 00 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9 b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 f3 c3 66 > [ 32.862680] RSP: 0000:ffffc900000ebb90 EFLAGS: 00010206 > [ 32.863309] RAX: 0000000000000000 RBX: ffff88001c67c8a0 RCX: 0000000000000000 > [ 32.864182] RDX: 0000000000000000 RSI: ffff88001c67c000 RDI: ffff88001c67c8a0 > [ 32.865206] RBP: ffff88001c7d03a0 R08: ffff88001c67c8a0 R09: ffff88001c7d0330 > [ 32.866359] R10: ffffffff822c3a98 R11: 0000000000000001 R12: ffff88001c67c000 > [ 32.867213] R13: ffff88001c7d0370 R14: ffffffff8207eb78 R15: ffff88001c67c800 > [ 32.868075] FS: 0000000000000000(0000) GS:ffff88001da00000(0000) knlGS:0000000000000000 > [ 32.868983] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 32.869659] CR2: 0000000000000000 CR3: 000000000220a000 CR4: 00000000000006f0 > [ 32.870599] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 > [ 32.871598] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 > [ 32.872549] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b > > Since drm_mode_hsync() has the logic to check mode->htotal, I just extend it to cover the case htotal==0. Signed-off-by: Tina Zhang <tina.zhang@intel.com> Cc: Adam Jackson <ajax@redhat.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel@ffwll.ch> [danvet: Add additional explanations + cc: stable.] Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/1548228539-3061-1-git-send-email-tina.zhang@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mic: vop: Fix use-after-free on removeVincent Whitchurch1-1/+3
commit 70ed7148dadb812f2f7c9927e98ef3cf4869dfa9 upstream. KASAN detects a use-after-free when vop devices are removed. This problem was introduced by commit 0063e8bbd2b62d136 ("virtio_vop: don't kfree device on register failure"). That patch moved the freeing of the struct _vop_vdev to the release function, but failed to ensure that vop holds a reference to the device when it doesn't want it to go away. A kfree() was replaced with a put_device() in the unregistration path, but the last reference to the device is already dropped in unregister_virtio_device() so the struct is freed before vop is done with it. Fix it by holding a reference until cleanup is done. This is similar to the fix in virtio_pci in commit 2989be09a8a9d6 ("virtio_pci: fix use after free on release"). ================================================================== BUG: KASAN: use-after-free in vop_scan_devices+0xc6c/0xe50 [vop] Read of size 8 at addr ffff88800da18580 by task kworker/0:1/12 CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.0.0-rc4+ #53 Workqueue: events vop_hotplug_devices [vop] Call Trace: dump_stack+0x74/0xbb print_address_description+0x5d/0x2b0 ? vop_scan_devices+0xc6c/0xe50 [vop] kasan_report+0x152/0x1aa ? vop_scan_devices+0xc6c/0xe50 [vop] ? vop_scan_devices+0xc6c/0xe50 [vop] vop_scan_devices+0xc6c/0xe50 [vop] ? vop_loopback_free_irq+0x160/0x160 [vop_loopback] process_one_work+0x7c0/0x14b0 ? pwq_dec_nr_in_flight+0x2d0/0x2d0 ? do_raw_spin_lock+0x120/0x280 worker_thread+0x8f/0xbf0 ? __kthread_parkme+0x78/0xf0 ? process_one_work+0x14b0/0x14b0 kthread+0x2ae/0x3a0 ? kthread_park+0x120/0x120 ret_from_fork+0x3a/0x50 Allocated by task 12: kmem_cache_alloc_trace+0x13a/0x2a0 vop_scan_devices+0x473/0xe50 [vop] process_one_work+0x7c0/0x14b0 worker_thread+0x8f/0xbf0 kthread+0x2ae/0x3a0 ret_from_fork+0x3a/0x50 Freed by task 12: kfree+0x104/0x310 device_release+0x73/0x1d0 kobject_put+0x14f/0x420 unregister_virtio_device+0x32/0x50 vop_scan_devices+0x19d/0xe50 [vop] process_one_work+0x7c0/0x14b0 worker_thread+0x8f/0xbf0 kthread+0x2ae/0x3a0 ret_from_fork+0x3a/0x50 The buggy address belongs to the object at ffff88800da18008 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 1400 bytes inside of 2048-byte region [ffff88800da18008, ffff88800da18808) The buggy address belongs to the page: page:ffffea0000368600 count:1 mapcount:0 mapping:ffff88801440dbc0 index:0x0 compound_mapcount: 0 flags: 0x4000000000010200(slab|head) raw: 4000000000010200 ffffea0000378608 ffffea000037a008 ffff88801440dbc0 raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88800da18480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800da18500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88800da18580: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88800da18600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800da18680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fixes: 0063e8bbd2b62d136 ("virtio_vop: don't kfree device on register failure") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15firmware: arm_scmi: provide the mandatory device release callbackSudeep Holla1-2/+7
commit 46edb8d1322c1763dd04e179992f8e9996085047 upstream. The device/driver model clearly mandates that bus driver that discover and allocate the device must set the release callback. This callback will be used to free the device after all references have gone away. scmi bus driver is missing the obvious callback which will result in the following warning if the device is unregistered: Device 'scmi_dev.1' does not have a release() function, it is broken and must be fixed. See Documentation/kobject.txt. WARNING at drivers/base/core.c:922 device_release+0x8c/0xa0 Hardware name: ARM LTD Juno Development Platform BIOS EDK II Jan 21 2019 Workqueue: events deferred_probe_work_func pstate: 60000005 (nZCv daif -PAN -UAO) pc : device_release+0x8c/0xa0 lr : device_release+0x8c/0xa0 Call trace: device_release+0x8c/0xa0 kobject_put+0x8c/0x208 device_unregister+0x30/0x78 scmi_device_destroy+0x28/0x50 scmi_probe+0x354/0x5b0 platform_drv_probe+0x58/0xa8 really_probe+0x2c4/0x3e8 driver_probe_device+0x12c/0x148 __device_attach_driver+0xac/0x150 bus_for_each_drv+0x78/0xd8 __device_attach+0xe0/0x168 device_initial_probe+0x24/0x30 bus_probe_device+0xa0/0xa8 deferred_probe_work_func+0x8c/0xe0 process_one_work+0x1f0/0x478 worker_thread+0x22c/0x450 kthread+0x134/0x138 ret_from_fork+0x10/0x1c ---[ end trace 420bdb7f6af50937 ]--- Fix the issue by providing scmi_device_release callback. We have everything required for device release already in scmi_device_destroy, so we just need to move freeing of the device to scmi_device_release. Fixes: 933c504424a2 ("firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices") Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org # 4.17+ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15pinctrl: cherryview: fix Strago DMI workaroundDmitry Torokhov1-4/+4
commit e3f72b749da2bf63bed7409e416f160418d475b6 upstream. Well, hopefully 3rd time is a charm. We tried making that check DMI_BIOS_VERSION and DMI_BOARD_VERSION, but the real one is DMI_PRODUCT_VERSION. Fixes: 86c5dd6860a6 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197953 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1631930 Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15pinctrl: sunxi: Correct number of IRQ banks on H6 main pin controllerChen-Yu Tsai1-1/+1
commit 10098709b4ee6f6f19f25ba81d9c6f83518c584c upstream. The H6 main pin controller has four banks of interrupt-triggering pins. The driver as originally submitted only specified three, but had pin descriptions referencing a fourth bank. This results in a out-of-bounds access into .irq_array of struct sunxi_pinctrl. This however did not result in a crash until v4.20, with commit a66d972465d1 ("devres: Align data[] to ARCH_KMALLOC_MINALIGN"), which changed the alignment of memory region returned by devm_kcalloc(). The increase likely moved the out-of-bounds access into the next, unmapped page. With KASAN on, the bug is quite clear: BUG: KASAN: slab-out-of-bounds in sunxi_pinctrl_init_with_variant+0x49c/0x12b8 Write of size 4 at addr ffff80002c680280 by task swapper/0/1 CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.0.0-rc1-00016-gc480a5e6a077 #3 Hardware name: OrangePi Lite2 (DT) Call trace: dump_backtrace+0x0/0x220 show_stack+0x14/0x20 dump_stack+0xac/0xd4 print_address_description+0x60/0x25c kasan_report+0x14c/0x1ac __asan_store4+0x80/0xa0 sunxi_pinctrl_init_with_variant+0x49c/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Allocated by task 1: kasan_kmalloc.part.0+0x4c/0x100 kasan_kmalloc+0xc4/0xe8 kasan_slab_alloc+0x14/0x20 __kmalloc_track_caller+0x130/0x238 devm_kmalloc+0x34/0xd0 sunxi_pinctrl_init_with_variant+0x1d8/0x12b8 h6_pinctrl_probe+0x18/0x20 platform_drv_probe+0x6c/0xc8 really_probe+0x244/0x4b0 driver_probe_device.part.4+0x11c/0x164 __driver_attach+0x120/0x190 bus_for_each_dev+0xe8/0x158 driver_attach+0x30/0x40 bus_add_driver+0x308/0x318 driver_register+0xbc/0x1d0 __platform_driver_register+0x7c/0x88 h6_pinctrl_driver_init+0x18/0x20 do_one_initcall+0xd4/0x208 kernel_init_freeable+0x230/0x2c8 kernel_init+0x10/0x108 ret_from_fork+0x10/0x1c Freed by task 0: (stack is not available) The buggy address belongs to the object at ffff80002c680080 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 0 bytes to the right of 512-byte region [ffff80002c680080, ffff80002c680280) The buggy address belongs to the page: page:ffff7e0000b1a000 count:1 mapcount:0 mapping:ffff80002e00c780 index:0xffff80002c683c80 compound_mapcount: 0 flags: 0x10200(slab|head) raw: 0000000000010200 ffff80002e003a10 ffff80002e003a10 ffff80002e00c780 raw: ffff80002c683c80 0000000000100001 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff80002c680180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff80002c680200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff80002c680280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff80002c680300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff80002c680380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Correct the number of IRQ banks so there are no more mismatches. Fixes: c8a830904991 ("pinctrl: sunxi: add support for the Allwinner H6 main pin controller") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mei: me: add ice lake point device id.Tomas Winkler2-0/+4
commit efe814e90b98aed6d655b5a4092b9114b8b26e42 upstream. Add icelake mei device id. Cc: <stable@vger.kernel.org> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15misc: vexpress: Off by one in vexpress_syscfg_exec()Dan Carpenter1-1/+1
commit f8a70d8b889f180e6860cb1f85fed43d37844c5a upstream. The > comparison should be >= to prevent reading beyond the end of the func->template[] array. (The func->template array is allocated in vexpress_syscfg_regmap_init() and it has func->num_templates elements.) Fixes: 974cc7b93441 ("mfd: vexpress: Define the device as MFD cells") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15iio: ti-ads8688: Update buffer allocation for timestampsDan Murphy1-1/+2
commit f214ff521fb1f861c8d7f7d0af98b06bf61b3369 upstream. Per Jonathan Cameron, the buffer needs to allocate room for a 64 bit timestamp as well as the channels. Change the buffer to allocate this additional space. Fixes: 2a86487786b5c ("iio: adc: ti-ads8688: add trigger and buffer support") Signed-off-by: Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsiusMatt Ranostay1-4/+3
commit 0808831dc62e90023ad14ff8da4804c7846e904b upstream. IIO_TEMP scale value for temperature was incorrect and not in millicelsius as required by the ABI documentation. Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com> Fixes: 27dec00ecf2d (iio: chemical: add Atlas pH-SM sensor support) Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15iio: adc: axp288: Fix TS-pin handlingHans de Goede1-16/+60
commit 9bcf15f75cac3c6a00d8f8083a635de9c8537799 upstream. Prior to this commit there were 3 issues with our handling of the TS-pin: 1) There are 2 ways how the firmware can disable monitoring of the TS-pin for designs which do not have a temperature-sensor for the battery: a) Clearing bit 0 of the AXP20X_ADC_EN1 register b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring Prior to this commit we were unconditionally setting both bits to the value used on devices with a TS. This causes the temperature protection to kick in on devices without a TS, such as the Jumper ezbook v2, causing them to not charge under Linux. This commit fixes this by using regmap_update_bits when updating these 2 registers, leaving the 2 mentioned bits alone. The next 2 problems are related to our handling of the current-source for the TS-pin. The current-source used for the battery temp-sensor (TS) is shared with the GPADC. For proper fuel-gauge and charger operation the TS current-source needs to be permanently on. But to read the GPADC we need to temporary switch the TS current-source to ondemand, so that the GPADC can use it, otherwise we will always read an all 0 value. 2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl register, overwriting various other unrelated bits. Specifically we were overwriting the current-source setting for the TS and GPIO0 pins, forcing it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet this was causing us to get a too high adc value (due to a too high current-source) resulting in the following errors being logged: ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR This commit fixes this by using regmap_update_bits to change only the relevant bits. 3) After reading the GPADC channel we were unconditionally enabling the TS current-source even on devices where the TS-pin is not used and the current-source thus was off before axp288_adc_read_raw call. This commit fixes this by making axp288_adc_set_ts a nop on devices where the ADC is not enabled for the TS-pin. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545 Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSDHans de Goede1-0/+1
commit dd957493baa586f1431490f97f9c7c45eaf8ab10 upstream. We've received a bugreport that using LPM with a SAMSUNG MZ7TE512HMHP-000L1 SSD leads to system instability, we already have a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 / PM851 OEM model, so it seems some of these models have a LPM issue. This commits adds a NOLPM quirk for the model string from the new bugeport, to avoid the reported stability issues. Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mtd: rawnand: gpmi: fix MX28 bus master lockup problemMartin Kepplinger1-7/+6
commit d5d27fd9826b59979b184ec288e4812abac0e988 upstream. Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft reset may cause bus master lock up") for MX28 too. It has the same problem. Observed problem: once per 100,000+ MX28 reboots NAND read failed on DMA timeout errors: [ 1.770823] UBI: attaching mtd3 to ubi0 [ 2.768088] gpmi_nand: DMA timeout, last DMA :1 [ 3.958087] gpmi_nand: BCH timeout, last DMA :1 [ 4.156033] gpmi_nand: Error in ECC-based read: -110 [ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64 bytes from PEB 0:0, read only 0 bytes, retry [ 4.171283] step 1 error [ 4.173846] gpmi_nand: Chip: 0, Error -1 Without BCH soft reset we successfully executed 1,000,000 MX28 reboots. I have a quote from NXP regarding this problem, from July 18th 2016: "As the i.MX23 and i.MX28 are of the same generation, they share many characteristics. Unfortunately, also the erratas may be shared. In case of the documented erratas and the workarounds, you can also apply the workaround solution of one device on the other one. This have been reported, but I’m afraid that there are not an estimated date for updating the Errata documents. Please accept our apologies for any inconveniences this may cause." Fixes: 6f2a6a52560a ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems") Cc: stable@vger.kernel.org Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com> Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Acked-by: Han Xu <han.xu@nxp.com> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mtd: spinand: Fix the error/cleanup path in spinand_init()Boris Brezillon1-2/+2
commit c3c7dbf4887ab3ed9d611cd1f6e16937f8700743 upstream. The manufacturer specific initialization has already been done when block unlocking takes place, and if anything goes wrong during this procedure we should call spinand_manufacturer_cleanup(). Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mtd: spinand: Handle the case where PROGRAM LOAD does not reset the cacheBoris Brezillon1-22/+20
commit 13c15e07eedf26092054c8c71f2f47edb8388310 upstream. Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset the cache content to 0xFF (depends on vendor implementation), so we must fill the page cache entirely even if we only want to program the data portion of the page, otherwise we might corrupt the BBM or user data previously programmed in OOB area. Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Reported-by: Stefan Roese <sr@denx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-15mtd: Make sure mtd->erasesize is valid even if the partition is of size 0Boris Brezillon1-0/+4
commit ad4635153034c20c6f6e211e2ed3fd38b658649a upstream. Commit 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent erase properties") introduced a check to make sure ->erasesize and ->_erase values are consistent with the MTD_NO_ERASE flag. This patch did not take the 0 bytes partition case into account which can happen when the defined partition is outside the flash device memory range. Fix that by setting the partition erasesize to the parent erasesize. Fixes: 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent erase properties") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: <stable@vger.kernel.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-14Merge tag 'v4.19.21' into dev-4.19Joel Stanley216-869/+1691
This is the 4.19.21 stable release Signed-off-by: Joel Stanley <joel@jms.id.au>
2019-02-12ath9k: dynack: check da->enabled first in sampling routinesLorenzo Bianconi1-2/+2
commit 9d3d65a91f027b8a9af5e63752d9b78cb10eb92d upstream. Check da->enabled flag first in ath_dynack_sample_tx_ts and ath_dynack_sample_ack_ts routines in order to avoid useless processing Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12ath9k: dynack: make ewma estimation fasterLorenzo Bianconi4-12/+29
commit 0c60c490830a1a756c80f8de8d33d9c6359d4a36 upstream. In order to make propagation time estimation faster, use current sample as ewma output value during 'late ack' tracking Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12IB/hfi1: Add limit test for RC/UC send via loopbackMike Marciniszyn2-2/+12
commit 09ce351dff8e7636af0beb72cd4a86c3904a0500 upstream. Fix potential memory corruption and panic in loopback for IB_WR_SEND variants. The code blindly assumes the posted length will fit in the fetched rwqe, which is not a valid assumption. Fix by adding a limit test, and triggering the appropriate send completion and putting the QP in an error state. This mimics the handling for non-loopback QPs. Fixes: 15703461533a ("IB/{hfi1, qib, rdmavt}: Move ruc_loopback to rdmavt") Cc: <stable@vger.kernel.org> #v4.20+ Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
2019-02-12cacheinfo: Keep the old value if of_property_read_u32 failsHuacai Chen1-4/+2
commit 3a34c986324c07dde32903f7bb262e6138e77c2a upstream. Commit 448a5a552f336bd7b847b1951 ("drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number") makes cache size and number_of_sets be 0 if DT doesn't provide there values. I think this is unreasonable so make them keep the old values, which is the same as old kernels. Fixes: 448a5a552f33 ("drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number") Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12serial: sh-sci: Do not free irqs that have already been freedChris Brandt1-1/+8
commit 4d95987a32db53f3beca76f8c4c8309ef6a5f192 upstream. Since IRQs might be muxed on some parts, we need to pay attention when we are freeing them. Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20". Fixes: 628c534ae735 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts") Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2025-10-01 19:00:40 +0300