| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.
On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.
Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NVMe fixes from Christoph:
"Three more fixes for 4.13 below:
- fix the incorrect bit for the doorbell buffer features (Changpeng Liu)
- always use a 4k MR page size for RDMA, to not get in trouble with
offset in non-4k page size systems (no-op for x86) (Max Gurtovoy)
- and a fix for the new nvme host memory buffer support to keep the
descriptor list DMA mapped when the buffer is enabled (me)"
|
|
The NVMe 1.3 specification says in section 5.21.1.13:
"After a successful completion of a Set Features enabling the host memory
buffer, the host shall not write to the associated host memory region,
buffer size, or descriptor list until the host memory buffer has been
disabled."
While this doesn't state that the descriptor list must remain accessible
to the device it certainly implies it must remaing readable by the device.
So switch to a dma coherent allocation for the descriptor list just to be
safe - it's not like the cost for it matters compared to the actual
memory buffers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 87ad72a59a38 ("nvme-pci: implement host memory buffer support")
|
|
Due to various page sizes in the system (IOMMU/device/kernel), we
set the fabrics controller page size to 4k and block layer boundaries
accordinglly. In architectures that uses different kernel page size
we'll have a mismatch to the MR page size that may cause a mapping error.
Update the MR page size to correspond to the core ctrl settings.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c280 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.19.x-
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit 2a842acab109 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5bde ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a042 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://people.freedesktop.org/~syeh/repos_linux into drm-fixes
Single vmwgfx fix.
* 'drm-vmwgfx-fixes' of git://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Fix F26 Wayland screen update issue
|
|
The phy is connected at early stage of probe but not properly
disconnected if error occurs. This patch fixes the issue.
Also changing the return type of xgene_enet_check_phy_handle(),
since this function always returns success.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both the nfp_net_pf_app_start() and the nfp_net_pci_probe() functions
call nfp_net_pf_app_stop_ctrl(pf) so there is a double free. The free
should be done from the probe function because it's allocated there so
I have removed the call from nfp_net_pf_app_start().
Fixes: 02082701b974 ("nfp: create control vNICs and wire up rx/tx")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should inform user about wrong firmware version
by printing message in dmesg.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the HW supports up to 32 multicast filters we should
track count of multicast filters to avoid overflow.
If we attempt to add >32 multicast filter - just set NETIF_ALLMULTI flag
instead.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Igor Russkikh <Igor.Russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver choose the optimal interrupt throttling settings depends
of current link speed.
Due this bug link_status field from aq_hw is never updated and as result
always used same interrupt throttling values.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware has the HW Checksum Offload bug when small
TCP patckets (with length <= 60 bytes) has wrong "checksum valid" bit.
The solution is - ignore checksum valid bit for small packets
(with length <= 60 bytes) and mark this as CHECKSUM_NONE to allow
network stack recalculate checksum itself.
Fixes: ccf9a5ed14be ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of RSS queues should be not more than numbers of CPU.
Its does not make sense to increase perfomance, and also cause problems on
some motherboards.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes datapath spinlocks which does not perform any
useful work.
Fixes: 6e70637f9f1e ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vmwgfx currently cannot support non-blocking commit because when
vmw_*_crtc_page_flip is called, drm_atomic_nonblocking_commit()
schedules the update on a thread. This means vmw_*_crtc_page_flip
cannot rely on the new surface being bound before the subsequent
dirty and flush operations happen.
Cc: <stable@vger.kernel.org> # 4.12.x
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
|
|
Compare the number of bytes actually seen on the wire to the byte
count field returned by the slave device.
Previously we just overwrote the byte count returned by the slave
with the real byte count and let the caller figure out if the
message was sane.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
According to Table 15-14 of the C2000 EDS (Intel doc #510524) the
rx data pointed to by the descriptor dptr contains the byte count.
desc->rxbytes reports all bytes read on the wire, including the
"byte count" byte. So if a device sends 4 bytes in response to a
block read, on the wire and in the DMA buffer we see:
count data1 data2 data3 data4
0x04 0xde 0xad 0xbe 0xef
That's what we want to return in data->block to the next level.
Instead we were actually prefixing that with desc->rxbytes:
bad
count count data1 data2 data3 data4
0x05 0x04 0xde 0xad 0xbe 0xef
This was discovered while developing a BMC solution relying on the
ipmi_ssif.c driver which was trying to interpret the bogus length
field as part of the IPMI response.
Signed-off-by: Stephen Douthit <stephend@adiengineering.com>
Tested-by: Dan Priamo <danp@adiengineering.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Driver Changes:
- bridge/sii8620: Fix out-of-bounds write to incorrect register
Cc: Maciej Purski <m.purski@samsung.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
* tag 'drm-misc-fixes-2017-08-28' of git://anongit.freedesktop.org/git/drm-misc:
drm/bridge/sii8620: Fix memory corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Late fixes for libata. There's a minor platform driver fix but the
important one is READ LOG PAGE.
This is a new ATA command which is used to test some optional features
but it broke probing of some devices - they locked up instead of
failing the unknown command.
Christoph tried blacklisting, but, after finding out there are
multiple devices which fail this way, backed off to testing feature
bit in IDENTIFY data first, which is a bit lossy (we can miss features
on some devices) but should be a lot safer"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
Revert "libata: quirk read log on no-name M.2 SSD"
libata: check for trusted computing in IDENTIFY DEVICE data
libata: quirk read log on no-name M.2 SSD
sata: ahci-da850: Fix some error handling paths in 'ahci_da850_probe()'
|
|
This reverts commit 35f0b6a779b8b7a98faefd7c1c660b4dac9a5c26.
We now conditionalize issuing of READ LOG PAGE on the TRUSTED
COMPUTING SUPPORTED bit in the identity data and this shouldn't be
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ATA-8 and later mirrors the TRUSTED COMPUTING SUPPORTED bit in word 48 of
the IDENTIFY DEVICE data. Check this before issuing a READ LOG PAGE
command to avoid issues with buggy devices. The only downside is that
we can't support Security Send / Receive for a device with an older
revision due to the conflicting use of this field in earlier
specifications.
tj: The reason we need this is because some devices which don't
support READ LOG PAGE lock up after getting issued that command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen into for-linus
Pull xen-blkback fix from Konrad:
"[...] A bug-fix when shutting down xen block backend driver with
multiple queues and the driver not clearing all of them."
|
|
git://people.freedesktop.org/~syeh/repos_linux into drm-next
vmwgfx add fence fd support.
* 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Summary:
- Provide NV12MT pixel format support of Mixer driver in generic way.
- Refactor Exynos KMS drivers
. Refactoring to panel detection way
. Refactoring to setting up possible_crtcs
. Refactoring to video and command mode support
- Some cleanups
* tag 'exynos-drm-next-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: simplify set_pixfmt() in DECON and FIMD drivers
drm/exynos: consistent use of cpp
drm/exynos: mixer: remove src offset from mixer_graph_buffer()
drm/exynos: mixer: simplify mixer_graph_buffer()
drm/exynos: mixer: simplify vp_video_buffer()
drm/exynos: mixer: enable NV12MT support for the video plane
drm/exynos: mixer: fix chroma comment in vp_video_buffer()
arm64: dts: exynos: remove i80-if-timings nodes
dt-bindings: exynos5433-decon: remove i80-if-timings property
drm/exynos/decon5433: use mode info stored in CRTC to detect i80 mode
drm/exynos: add mode_valid callback to exynos_drm
drm/exynos/decon5433: refactor irq requesting code
drm/exynos/mic: use mode info stored in CRTC to detect i80 mode
drm/exynos/dsi: propagate info about command mode from panel
drm/exynos/dsi: refactor panel detection logic
drm/exynos: use helper to set possible crtcs
drm/exynos/decon5433: use readl_poll_timeout helpers
|
|
This IOCTL provides a mechanism for userspace to trigger a sync object
directly. There are other ways that userspace can trigger a syncobj
such as submitting a dummy batch somewhere or hanging on to a triggered
sync_file and doing an import. This just provides an easy way to
manually trigger the sync object without weird hacks.
The motivation for this IOCTL is Vulkan fences. Vulkan lets you create
a fence already in the signaled state so that you can wait on it
immediatly without stalling. We could also handle this with a new
create flag to ask the driver to create a syncobj that is already
signaled but the IOCTL seemed a bit cleaner and more generic.
v2:
- Take an array of sync objects (Dave Airlie)
v3:
- Throw -EINVAL if pad != 0
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This just resets the dma_fence to NULL so it looks like it's never been
signaled. This will be useful once we add the new wait API for allowing
wait on "submit and signal" behavior.
v2:
- Take an array of sync objects (Dave Airlie)
v3:
- Throw -EINVAL if pad != 0
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Passing commands for logging to t4_record_mbox() with size
MBOX_LEN, when the actual command size is actually smaller,
causes out-of-bounds stack accesses in t4_record_mbox() while
copying command words here:
for (i = 0; i < size / 8; i++)
entry->cmd[i] = be64_to_cpu(cmd[i]);
Up to 48 bytes from the stack are then leaked to debugfs.
This happens whenever we send (and log) commands described by
structs fw_sched_cmd (32 bytes leaked), fw_vi_rxmode_cmd (48),
fw_hello_cmd (48), fw_bye_cmd (48), fw_initialize_cmd (48),
fw_reset_cmd (48), fw_pfvf_cmd (32), fw_eq_eth_cmd (16),
fw_eq_ctrl_cmd (32), fw_eq_ofld_cmd (32), fw_acl_mac_cmd(16),
fw_rss_glb_config_cmd(32), fw_rss_vi_config_cmd(32),
fw_devlog_cmd(32), fw_vi_enable_cmd(48), fw_port_cmd(32),
fw_sched_cmd(32), fw_devlog_cmd(32).
The cxgb4vf driver got this right instead.
When we call t4_record_mbox() to log a command reply, a MBOX_LEN
size can be used though, as get_mbox_rpl() will fill cmd_rpl up
completely.
Fixes: 7f080c3f2ff0 ("cxgb4: Add support to enable logging of firmware mailbox commands")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the bindings have been controversial, and we follow the DT stable ABI
rule, we shouldn't let a driver with a DT binding that might change slip
through in a stable release.
Remove the compatibles to make sure the driver will not probe and no-one
will start using the binding currently implemented. This commit will
obviously need to be reverted in due time.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the vlan tci field was incorrectly exact matched. This patch
fixes this by using the flow dissector to populate the vlan tci field.
Fixes: 5571e8c9f241 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously when calculating the supported key layers MPLS, IPv4/6
TTL and TOS were not considered. This patch checks that the TTL and
TOS fields are masked out before offloading. Additionally this patch
checks that MPLS packets are correctly handled, by not offloading them.
Fixes: af9d842c1354 ("nfp: extend flower add flow offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously flow dissectors were referenced without first checking that
they are in use and correctly populated by TC. This patch fixes this by
checking each flow dissector key before referencing them.
Fixes: 5571e8c9f241 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The wait ioctl has a bunch of code to read an syncobj handle array from
userspace and turn it into an array of syncobj pointers. We're about to
add two new IOCTLs which will need to work with arrays of syncobj
handles so let's make some helpers.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Vulkan VkFence semantics require that the application be able to perform
a CPU wait on work which may not yet have been submitted. This is
perfectly safe because the CPU wait has a timeout which will get
triggered eventually if no work is ever submitted. This behavior is
advantageous for multi-threaded workloads because, so long as all of the
threads agree on what fences to use up-front, you don't have the extra
cross-thread synchronization cost of thread A telling thread B that it
has submitted its dependent work and thread B is now free to wait.
Within a single process, this can be implemented in the userspace driver
by doing exactly the same kind of tracking the app would have to do
using posix condition variables or similar. However, in order for this
to work cross-process (as is required by VK_KHR_external_fence), we need
to handle this in the kernel.
This commit adds a WAIT_FOR_SUBMIT flag to DRM_IOCTL_SYNCOBJ_WAIT which
instructs the IOCTL to wait for the syncobj to have a non-null fence and
then wait on the fence. Combined with DRM_IOCTL_SYNCOBJ_RESET, you can
easily get the Vulkan behavior.
v2:
- Fix a bug in the invalid syncobj error path
- Unify the wait-all and wait-any cases
v3:
- Unify the timeout == 0 case a bit with the timeout > 0 case
- Use wait_event_interruptible_timeout
v4:
- Use proxy fence
v5:
- Revert to a combination of v2 and v3
- Don't use proxy fences
- Don't use wait_event_interruptible_timeout because it just adds an
extra layer of callbacks
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This requests that the driver create the sync object such that it
already has a signaled dma_fence attached. Because we don't need
anything in particular (just something signaled), we use a dummy null
fence. This is useful for Vulkan which has a similar flag that can be
passed to vkCreateFence.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
It is useful in certain circumstances to know when the fence is replaced
in a syncobj. Specifically, it may be useful to know when the fence
goes from NULL to something valid. This does make syncobj_replace_fence
a little more expensive because it has to take a lock but, in the common
case where there is no callback list, it spends a very short amount of
time inside the lock.
v2:
- Don't lock in drm_syncobj_fence_get. We only really need to lock
around fence_replace to make the callback work.
v3:
- Fix the cb_list comment to make kbuild happy
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This interface will allow sync object to be used to back
Vulkan fences. This API is pretty much the vulkan fence waiting
API, and I've ported the code from amdgpu.
v2: accept relative timeout, pass remaining time back
to userspace.
v3: return to absolute timeouts.
v4: absolute zero = poll,
rewrite any/all code to have same operation for arrays
return -EINVAL for 0 fences.
v4.1: fixup fences allocation check, use u64_to_user_ptr
v5: move to sec/nsec, and use timespec64 for calcs.
v6: use -ETIME and drop the out status flag. (-ETIME
is suggested by ickle, I can feel a shed painting)
v7: talked to Daniel/Arnd, use ktime and ns everywhere.
v8: be more careful in the timeout calculations
use uint32_t for counter variables so we don't overflow
graciously handle -ENOINT being returned from dma_fence_wait_timeout
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The atomic exchange operation in drm_syncobj_replace_fence is sufficient
for the case where it races with itself. However, if you have a race
between a replace_fence and dma_fence_get(syncobj->fence), you may end
up with the entire replace_fence happening between the point in time
where the one thread gets the syncobj->fence pointer and when it calls
dma_fence_get() on it. If this happens, then the reference may be
dropped before we get a chance to get a new one. The new helper uses
dma_fence_get_rcu_safe to get rid of the race.
This is also needed because it allows us to do a bit more than just get
a reference in drm_syncobj_fence_get should we wish to do so.
v2:
- RCU isn't that scary
- Call rcu_read_lock/unlock
- Don't rename fence to _fence
- Make the helper static inline
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The function has far more in common with drm_syncobj_find than with
any in the get/put functions.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Currently the hikey dsi logic cannot generate accurate byte
clocks values for all pixel clock values. Thus if a mode clock
is selected that cannot match the calculated byte clock, the
device will boot with a blank screen.
This patch uses the new mode_valid callback (many thanks to
Jose Abreu for upstreaming it!) to ensure we don't select
modes we cannot generate.
Also, since the ade crtc code will adjust the mode in mode_set,
this patch also adds a mode_fixup callback which we use to make
sure we are validating the mode clock that will eventually be
used.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The mac address is only retrieved from h/w when using PPv2.1. Otherwise
the variable holding it is still checked and used if it contains a valid
value. As the variable isn't initialized to an invalid mac address
value, we end up with random mac addresses which can be the same for all
the ports handled by this PPv2 driver.
Fixes this by initializing the h/w mac address variable to {0}, which is
an invalid mac address value. This way the random assignation fallback
is called and all ports end up with their own addresses.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 2697582144dd ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The u-blox TOBY-L4 is a LTE Advanced (Cat 6) module with HSPA+ and 2G
fallback.
Unlike the TOBY-L2, this module has one single USB layout and exposes
several TTYs for control and a NCM interface for data. Connecting this
module may be done just by activating the desired PDP context with
'AT+CGACT=1,<cid>' and then running DHCP on the NCM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
User-modified input settings no longer survive a suspend/resume cycle.
Starting with 4.12, the touchpad is reinitialized on every reconnect
because the hardware appears to be different. This can be reproduced
by running the following as root:
echo -n reconnect >/sys/devices/platform/i8042/serio1/drvctl
A line like the following will show up in dmesg:
[30378.295794] psmouse serio1: synaptics: hardware appears to be
different: id(149271-149271), model(114865-114865),
caps(d047b3-d047b1), ext(b40000-b40000).
Note the single bit difference in caps: bit 1 (SYN_CAP_MULTIFINGER).
This happens because we modify our stored copy of the device info
capabilities when we enable advanced gesture mode but this change is
not reflected in the actual hardware capabilities.
It worked in the past because synaptics_query_hardware used to modify
the stored synaptics_device_info struct instead of filling in a new
one, as it does now.
Fix it by no longer faking the SYN_CAP_MULTIFINGER bit when setting
advanced gesture mode. This necessitated a small refactoring.
Fixes: 6c53694fb222 ("Input: synaptics - split device info into a separate structure")
Signed-off-by: Anthony Martin <ality@pbrane.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Ido reported that reading the log page on his systems fails,
so quirk it as it won't support ZBC or security protocols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Minor version bump to indicate support for fence FD
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Singh Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Added code to link a fence to a out_fence_fd file descriptor and
thread out_fence_fd down to vmw_execbuf_copy_fence_user() so it can be
copied into the IOCTL reply and be passed back up the the user.
v2:
Make sure to sync and clean up in case of failure
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Singh Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
This allows vmwgfx to wait on a fence created by another
device.
v2:
* Remove special handling for vmwgfx fence and just use dma_fence_wait()
* Use interruptible waits
* Added function documentation
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Singh Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
Make the fields and flags available.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Deepak Singh Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
|
