| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit e8245c68350104b6022b6783719e843d69ea7c43 upstream.
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d0e8e795623bd6229cf48bb7777a1c456c370ed upstream.
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0d106b74c558e3000aa0e058b4725cacb70ce77a upstream.
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 11b86a84bc535a602fcf72ba6b3aa4eaa748764f upstream.
Fix the values of DPAA2_FD_CTRL_FSE and DPAA2_FD_CTRL_FAERR,
which are shifted off by one bit.
Fixes: 39163c0ce0f48 ("staging: fsl-dpaa2/eth: Errors checking update")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 737aed947f9b5bd749a2684e13572ee99a1b8bae upstream.
The crypto API requires saving the last blocks of ciphertext
in req->info for use as IV for CTS mode. The ccree driver
was not doing this. This patch fixes that.
The bug was manifested with cts(cbc(aes)) mode in tcrypt tests.
Fixes: 302ef8ebb4b2 ("Add CryptoCell skcipher support")
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34ff1bf4920471cff66775dc39537b15c5f0feff upstream.
The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0. Fix this by shifting only by 4 bits to correctly get the upper nybble.
Detected by CoverityScan, CID#142891 ("Operands don't affect result")
Fixes: fa590c222fba ("staging: rts5208: add support for rts5208 and rts5288")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ed62ca2f4f51c17841ea39d98c0c409cb53a3e10 upstream.
While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:
[ 14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091
[ 14.012460] lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu
[ 14.012460] /1025536097, .owner_cpu: 0
[ 14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352
[ 14.012468] Hardware name: Google Kevin (DT)
[ 14.012471] Call trace:
[ 14.012483] [<....>] dump_backtrace+0x0/0x160
[ 14.012487] [<....>] show_stack+0x20/0x28
[ 14.012494] [<....>] dump_stack+0xb4/0xf0
[ 14.012500] [<....>] spin_dump+0x8c/0x98
[ 14.012504] [<....>] spin_bug+0x30/0x3c
[ 14.012508] [<....>] do_raw_spin_lock+0x40/0x164
[ 14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74
[ 14.012521] [<....>] __wake_up+0x2c/0x60
[ 14.012528] [<....>] async_completed+0x2d0/0x300
[ 14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138
[ 14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0
[ 14.012544] [<....>] xhci_irq+0x1314/0x1348
[ 14.012548] [<....>] usb_hcd_irq+0x40/0x50
[ 14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0
[ 14.012556] [<....>] handle_irq_event+0x4c/0x7c
[ 14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8
[ 14.012564] [<....>] generic_handle_irq+0x30/0x44
[ 14.012568] [<....>] __handle_domain_irq+0x90/0xbc
[ 14.012572] [<....>] gic_handle_irq+0xcc/0x18c
Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).
I analyzed and instrumented the code and reproduced. My current
belief is that this is happening:
1. async_completed() is called (from IRQ). Moves "as" onto the
completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
async_getcompleted(). Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
lock; removes "as" from completed list and frees it.
5. usbdev_release() is called. Frees "ps".
6. async_completed() finally continues running wake_up(). ...but
wake_up() has a pointer to the freed "ps".
The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time. The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):
<...>-2104 0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055 3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055 3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055 3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055 3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055 3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104 0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200
To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9e18d0c82f0c07f2a41898d4adbb698a953403ee upstream.
These will be required going forward.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 082df8be455ade361748f0385aa6c9c8d07be167 upstream.
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e1806 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5ded
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95463d ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5ded ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aaaa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e1806 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6b422b88b46353cf596e0db6dc0e39d50d90d6e upstream.
The following commit cause a regression on ATI chipsets.
'commit e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4f9 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1279ef74eeeb5f627f091c71d80dd7ac766c99d upstream.
Commit e0429362ab15
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.
Apparently model C920-C has the same issue so applying
the same quirk as well.
See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 169e86546f5712179709de23cd64bbb15f199fab upstream.
This commit adds support (an ID, really) for D-Link DWM-157 hardware
version C1 USB modem to option driver.
According to manufacturer-provided Windows INF file the device has four
serial ports:
"D-Link HSPA+DataCard Diagnostics Interface" (interface 2; modem port),
"D-Link HSPA+DataCard NMEA Device" (interface 3),
"D-Link HSPA+DataCard Speech Port" (interface 4),
"D-Link HSPA+DataCard Debug Port" (interface 5).
usb-devices output:
T: Bus=05 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7d0e Rev=03.00
S: Manufacturer=D-Link,Inc
S: Product=D-Link DWM-157
C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit de3af5bf259d7a0bfaac70441c8568ab5998d80c upstream.
Corsair Strafe RGB keyboard has trouble to initialize:
[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110
Although it may work after several times unpluging/pluging:
[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941
Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.
BugLink: https://bugs.launchpad.net/bugs/1678477
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull MIPS fixes from Ralf Baechle:
"The two indirect syscall fixes have sat in linux-next for a few days.
I did check back with a hardware designer to ensure a SYNC is really
what's required for the GIC fix and so the GIC fix didn't make it into
to linux-next in time for this final pull request.
It builds in local build tests and passes Imagination's test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
irqchip: mips-gic: SYNC after enabling GIC region
MIPS: Remove pt_regs adjustments in indirect syscall handler
MIPS: seccomp: Fix indirect syscall args
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The ismt driver had a problem with a rarely used transaction type and
the designware driver was made even more robust against non standard
ACPI tables"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Round down ACPI provided clk to nearest supported clk
i2c: ismt: Return EMSGSIZE for block reads with bogus length
i2c: ismt: Don't duplicate the receive length for block reads
|
|
Pull networking fixes from David Miller:
1) Fix handling of pinned BPF map nodes in hash of maps, from Daniel
Borkmann.
2) IPSEC ESP error paths leak memory, from Steffen Klassert.
3) We need an RCU grace period before freeing fib6_node objects, from
Wei Wang.
4) Must check skb_put_padto() return value in HSR driver, from FLorian
Fainelli.
5) Fix oops on PHY probe failure in ftgmac100 driver, from Andrew
Jeffery.
6) Fix infinite loop in UDP queue when using SO_PEEK_OFF, from Eric
Dumazet.
7) Use after free when tcf_chain_destroy() called multiple times, from
Jiri Pirko.
8) Fix KSZ DSA tag layer multiple free of SKBS, from Florian Fainelli.
9) Fix leak of uninitialized memory in sctp_get_sctp_info(),
inet_diag_msg_sctpladdrs_fill() and inet_diag_msg_sctpaddrs_fill().
From Stefano Brivio.
10) L2TP tunnel refcount fixes from Guillaume Nault.
11) Don't leak UDP secpath in udp_set_dev_scratch(), from Yossi
Kauperman.
12) Revert a PHY layer change wrt. handling of PHY_HALTED state in
phy_stop_machine(), it causes regressions for multiple people. From
Florian Fainelli.
13) When packets are sent out of br0 we have to clear the
offload_fwdq_mark value.
14) Several NULL pointer deref fixes in packet schedulers when their
->init() routine fails. From Nikolay Aleksandrov.
15) Aquantium devices cannot checksum offload correctly when the packet
is <= 60 bytes. From Pavel Belous.
16) Fix vnet header access past end of buffer in AF_PACKET, from
Benjamin Poirier.
17) Double free in probe error paths of nfp driver, from Dan Carpenter.
18) QOS capability not checked properly in DCB init paths of mlx5
driver, from Huy Nguyen.
19) Fix conflicts between firmware load failure and health_care timer in
mlx5, also from Huy Nguyen.
20) Fix dangling page pointer when DMA mapping errors occur in mlx5,
from Eran Ben ELisha.
21) ->ndo_setup_tc() in bnxt_en driver doesn't count rings properly,
from Michael Chan.
22) Missing MSIX vector free in bnxt_en, also from Michael Chan.
23) Refcount leak in xfrm layer when using sk_policy, from Lorenzo
Colitti.
24) Fix copy of uninitialized data in qlge driver, from Arnd Bergmann.
25) bpf_setsockopts() erroneously always returns -EINVAL even on
success. Fix from Yuchung Cheng.
26) tipc_rcv() needs to linearize the SKB before parsing the inner
headers, from Parthasarathy Bhuvaragan.
27) Fix deadlock between link status updates and link removal in netvsc
driver, from Stephen Hemminger.
28) Missed locking of page fragment handling in ESP output, from Steffen
Klassert.
29) Fix refcnt leak in ebpf congestion control code, from Sabrina
Dubroca.
30) sxgbe_probe_config_dt() doesn't check devm_kzalloc()'s return value,
from Christophe Jaillet.
31) Fix missing ipv6 rx_dst_cookie update when rx_dst is updated during
early demux, from Paolo Abeni.
32) Several info leaks in xfrm_user layer, from Mathias Krause.
33) Fix out of bounds read in cxgb4 driver, from Stefano Brivio.
34) Properly propagate obsolete state of route upwards in ipv6 so that
upper holders like xfrm can see it. From Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (118 commits)
udp: fix secpath leak
bridge: switchdev: Clear forward mark when transmitting packet
mlxsw: spectrum: Forbid linking to devices that have uppers
wl1251: add a missing spin_lock_init()
Revert "net: phy: Correctly process PHY_HALTED in phy_stop_machine()"
net: dsa: bcm_sf2: Fix number of CFP entries for BCM7278
kcm: do not attach PF_KCM sockets to avoid deadlock
sch_tbf: fix two null pointer dereferences on init failure
sch_sfq: fix null pointer dereference on init failure
sch_netem: avoid null pointer deref on init failure
sch_fq_codel: avoid double free on init failure
sch_cbq: fix null pointer dereferences on init failure
sch_hfsc: fix null pointer deref and double free on init failure
sch_hhf: fix null pointer dereference on init failure
sch_multiq: fix double free on init failure
sch_htb: fix crash on init failure
net/mlx5e: Fix CQ moderation mode not set properly
net/mlx5e: Fix inline header size for small packets
net/mlx5: E-Switch, Unload the representors in the correct order
net/mlx5e: Properly resolve TC offloaded ipv6 vxlan tunnel source address
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple drivers fixes (Synaptics PS/2, Xpad)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - fix PowerA init quirk for some gamepad models
Input: synaptics - fix device info appearing different on reconnect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull two more MMC fixes from Ulf Hansson:
"MMC core:
- Fix block status codes
MMC host:
- sdhci-xenon: Fix SD bus voltage select"
* tag 'mmc-v4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: add set_power callback
mmc: block: Fix block status codes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Three more bug fixes for v4.13.
The two memory management related fixes are quite new, they fix kernel
crashes that can be triggered by user space.
The third commit fixes a bug in the vfio ccw translation code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix BUG_ON in crst_table_upgrade
s390/mm: fork vs. 5 level page tabel
vfio: ccw: fix bad ptr math for TIC cda translation
|
|
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc13042f ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"Unfortunately a few issues that warrant sending another pull request,
even if I had hoped to avoid it. This contains:
- A fix for multiqueue xen-blkback, on tear down / disconnect.
- A few fixups for NVMe, including a wrong bit definition, fix for
host memory buffers, and an nvme rdma page size fix"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix the definition of the doorbell buffer config support bit
nvme-pci: use dma memory for the host memory buffer descriptors
nvme-rdma: default MR page size to 4k
xen-blkback: stop blkback thread of every queue in xen_blkif_disconnect
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- A couple fixes for bugs introduced as part of the blk_status_t block
layer changes during the 4.13 merge window
- A printk throttling fix to use discrete rate limiting state for each
DM log level
- A stable@ fix for DM multipath that delays request requeueing to
avoid CPU lockup if/when the request queue is "dying"
* tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: do not lock up a CPU with requeuing activity
dm: fix printk() rate limiting code
dm mpath: retry BLK_STS_RESOURCE errors
dm: fix the second dec_pending() argument in __split_and_process_bio()
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: xen-devel@lists.xenproject.org (moderated for non-subscribers)
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: linux-rdma@vger.kernel.org
Cc: Dean Luick <dean.luick@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Tested-by: Leon Romanovsky <leonro@mellanox.com>
Cc: linux-rdma@vger.kernel.org
Cc: Artemy Kovalyov <artemyko@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Calls to mmu_notifier_invalidate_page() were replaced by calls to
mmu_notifier_invalidate_range() and are now bracketed by calls to
mmu_notifier_invalidate_range_start()/end()
Remove now useless invalidate_page callback.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
wl1251: add a missing spin_lock_init()
This fixes the following kernel warning:
[ 5668.771453] BUG: spinlock bad magic on CPU#0, kworker/u2:3/9745
[ 5668.771850] lock: 0xce63ef20, .magic: 00000000, .owner: <none>/-1,
.owner_cpu: 0
[ 5668.772277] CPU: 0 PID: 9745 Comm: kworker/u2:3 Tainted: G W
4.12.0-03002-gec979a4-dirty #40
[ 5668.772796] Hardware name: Nokia RX-51 board
[ 5668.773071] Workqueue: phy1 wl1251_irq_work
[ 5668.773345] [<c010c9e4>] (unwind_backtrace) from [<c010a274>]
(show_stack+0x10/0x14)
[ 5668.773803] [<c010a274>] (show_stack) from [<c01545a4>]
(do_raw_spin_lock+0x6c/0xa0)
[ 5668.774230] [<c01545a4>] (do_raw_spin_lock) from [<c06ca578>]
(_raw_spin_lock_irqsave+0x10/0x18)
[ 5668.774658] [<c06ca578>] (_raw_spin_lock_irqsave) from [<c048c010>]
(wl1251_op_tx+0x38/0x5c)
[ 5668.775115] [<c048c010>] (wl1251_op_tx) from [<c06a12e8>]
(ieee80211_tx_frags+0x188/0x1c0)
[ 5668.775543] [<c06a12e8>] (ieee80211_tx_frags) from [<c06a138c>]
(__ieee80211_tx+0x6c/0x130)
[ 5668.775970] [<c06a138c>] (__ieee80211_tx) from [<c06a3dbc>]
(ieee80211_tx+0xdc/0x104)
[ 5668.776367] [<c06a3dbc>] (ieee80211_tx) from [<c06a4af0>]
(__ieee80211_subif_start_xmit+0x454/0x8c8)
[ 5668.776824] [<c06a4af0>] (__ieee80211_subif_start_xmit) from
[<c06a4f94>] (ieee80211_subif_start_xmit+0x30/0x2fc)
[ 5668.777343] [<c06a4f94>] (ieee80211_subif_start_xmit) from
[<c0578848>] (dev_hard_start_xmit+0x80/0x118)
...
by adding the missing spin_lock_init().
Reported-by: Pavel Machek <pavel@ucw.cz>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PowerA gamepad initialization quirk worked with the PowerA
wired gamepad I had around (0x24c6:0x543a), but a user reported [0]
that it didn't work for him, even though our gamepads shared the
same vendor and product IDs.
When I initially implemented the PowerA quirk, I wanted to avoid
actually triggering the rumble action during init. My tests showed
that my gamepad would work correctly even if it received a rumble
of 0 intensity, so that's what I went with.
Unfortunately, this apparently isn't true for all models (perhaps
a firmware difference?). This non-working gamepad seems to require
the real magic rumble packet that the Microsoft driver sends, which
actually vibrates the gamepad. To counteract this effect, I still
send the old zero-rumble PowerA quirk packet which cancels the
rumble effect before the motors can spin up enough to vibrate.
[0]: https://github.com/paroj/xpad/issues/48#issuecomment-313904867
Reported-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Tested-by: Kyle Beauchamp <kyleabeauchamp@gmail.com>
Fixes: 81093c9848a7 ("Input: xpad - support some quirky Xbox One pads")
Cc: stable@vger.kernel.org # v4.12
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.
This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.
Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c2188 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into fixes
Pull vfio-ccw fix from Cornelia Huck:
"A bugfix in the ccw translation code."
|
|
This reverts commit 7ad813f208533cebfcc32d3d7474dc1677d1b09a ("net: phy:
Correctly process PHY_HALTED in phy_stop_machine()") because it is
creating the possibility for a NULL pointer dereference.
David Daney provide the following call trace and diagram of events:
When ndo_stop() is called we call:
phy_disconnect()
+---> phy_stop_interrupts() implies: phydev->irq = PHY_POLL;
+---> phy_stop_machine()
| +---> phy_state_machine()
| +----> queue_delayed_work(): Work queued.
+--->phy_detach() implies: phydev->attached_dev = NULL;
Now at a later time the queued work does:
phy_state_machine()
+---->netif_carrier_off(phydev->attached_dev): Oh no! It is NULL:
CPU 12 Unable to handle kernel paging request at virtual address
0000000000000048, epc == ffffffff80de37ec, ra == ffffffff80c7c
Oops[#1]:
CPU: 12 PID: 1502 Comm: kworker/12:1 Not tainted 4.9.43-Cavium-Octeon+ #1
Workqueue: events_power_efficient phy_state_machine
task: 80000004021ed100 task.stack: 8000000409d70000
$ 0 : 0000000000000000 ffffffff84720060 0000000000000048 0000000000000004
$ 4 : 0000000000000000 0000000000000001 0000000000000004 0000000000000000
$ 8 : 0000000000000000 0000000000000000 00000000ffff98f3 0000000000000000
$12 : 8000000409d73fe0 0000000000009c00 ffffffff846547c8 000000000000af3b
$16 : 80000004096bab68 80000004096babd0 0000000000000000 80000004096ba800
$20 : 0000000000000000 0000000000000000 ffffffff81090000 0000000000000008
$24 : 0000000000000061 ffffffff808637b0
$28 : 8000000409d70000 8000000409d73cf0 80000000271bd300 ffffffff80c7804c
Hi : 000000000000002a
Lo : 000000000000003f
epc : ffffffff80de37ec netif_carrier_off+0xc/0x58
ra : ffffffff80c7804c phy_state_machine+0x48c/0x4f8
Status: 14009ce3 KX SX UX KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 0000000000000048
PrId : 000d9501 (Cavium Octeon III)
Modules linked in:
Process kworker/12:1 (pid: 1502, threadinfo=8000000409d70000,
task=80000004021ed100, tls=0000000000000000)
Stack : 8000000409a54000 80000004096bab68 80000000271bd300 80000000271c1e00
0000000000000000 ffffffff808a1708 8000000409a54000 80000000271bd300
80000000271bd320 8000000409a54030 ffffffff80ff0f00 0000000000000001
ffffffff81090000 ffffffff808a1ac0 8000000402182080 ffffffff84650000
8000000402182080 ffffffff84650000 ffffffff80ff0000 8000000409a54000
ffffffff808a1970 0000000000000000 80000004099e8000 8000000402099240
0000000000000000 ffffffff808a8598 0000000000000000 8000000408eeeb00
8000000409a54000 00000000810a1d00 0000000000000000 8000000409d73de8
8000000409d73de8 0000000000000088 000000000c009c00 8000000409d73e08
8000000409d73e08 8000000402182080 ffffffff808a84d0 8000000402182080
...
Call Trace:
[<ffffffff80de37ec>] netif_carrier_off+0xc/0x58
[<ffffffff80c7804c>] phy_state_machine+0x48c/0x4f8
[<ffffffff808a1708>] process_one_work+0x158/0x368
[<ffffffff808a1ac0>] worker_thread+0x150/0x4c0
[<ffffffff808a8598>] kthread+0xc8/0xe0
[<ffffffff808617f0>] ret_from_kernel_thread+0x14/0x1c
The original motivation for this change originated from Marc Gonzales
indicating that his network driver did not have its adjust_link callback
executing with phydev->link = 0 while he was expecting it.
PHYLIB has never made any such guarantees ever because phy_stop() merely just
tells the workqueue to move into PHY_HALTED state which will happen
asynchronously.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 7ad813f20853 ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-08-30
This series contains some misc fixes to the mlx5 driver.
Please pull and let me know if there's any problem.
For -stable:
Kernels >= 4.12
net/mlx5e: Fix CQ moderation mode not set properly
net/mlx5e: Don't override user RSS upon set channels
Kernels >= 4.11
net/mlx5e: Properly resolve TC offloaded ipv6 vxlan tunnel source address
Kernels >= 4.10
net/mlx5e: Fix DCB_CAP_ATTR_DCBX capability for DCBNL getcap
net/mlx5e: Check for qos capability in dcbnl_initialize
Kernels >= 4.9
net/mlx5e: Fix dangling page pointer on DMA mapping error
Kernels >= 4.8
net/mlx5e: Fix inline header size for small packets
net/mlx5: E-Switch, Unload the representors in the correct order
net/mlx5: Fix arm SRQ command for ISSI version 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM7278 has only 128 entries while BCM7445 has the full 256 entries set,
fix that.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Two fixes (a vmwgfx and core drm fix) in the queue for 4.13 final,
hopefully that is it"
* tag 'drm-fixes-for-v4.13-rc8' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix F26 Wayland screen update issue
drm/bridge/sii8620: Fix memory corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: a NULL deref in qedf, an off by one in sg and a fix
to IPR to prevent an error on initialisation"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedf: Fix a potential NULL pointer dereference
scsi: sg: off by one in sg_ioctl()
scsi: ipr: Set no_report_opcodes for RAID arrays
|
|
cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.
Fixes: 6a9764efb255 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix inline header size, make sure it is not greater than skb len.
This bug effects small packets, for example L2 packets with size < 18.
Fixes: ae76715d153e ("net/mlx5e: Check the minimum inline header mode before xmit")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When changing from switchdev to legacy mode, all the representor port
devices (uplink nic and reps) are cleaned up. Part of this cleaning
process is removing the neigh entries and the hash table containing them.
However, a representor neigh entry might be linked to the uplink port
hash table and if the uplink nic is cleaned first the cleaning of the
representor will end up in null deref.
Fix that by unloading the representors in the opposite order of load.
Fixes: cb67b832921c ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.
Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.
Fixes: ce99f6b97fcd ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.
Tested:
when RSS default:
# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.
# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.
Fixes: 8bf368620486 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.
Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a25 ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.
Change arm_srq_cmd to use the correct command opcode for ISSI version
0.
Fixes: af1ba291c5e4 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.
This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.
Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
