summaryrefslogtreecommitdiff
path: root/drivers/usb
AgeCommit message (Collapse)AuthorFilesLines
2020-09-17usblp: fix race between disconnect() and read()Oliver Neukum1-0/+5
read() needs to check whether the device has been disconnected before it tries to talk to the device. Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: syzbot+be5b5f86a162a6c281e6@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20200917103427.15740-1-oneukum@suse.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-17ehci-hcd: Move include to keep CRC stableQuentin Perret2-1/+1
The CRC calculation done by genksyms is triggered when the parser hits EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the types of the function parameters, and uses that as the input for the CRC calculation. In the case of forward-declared structs, the type expands to 'UNKNOWN'. Following this, it appears that the result of the expansion of each type is cached somewhere, and seems to be re-used when/if the same type is seen again for another exported symbol in the same C file. Unfortunately, this can cause CRC 'stability' issues when a struct definition becomes visible in the middle of a C file. For example, let's assume code with the following pattern: struct foo; int bar(struct foo *arg) { /* Do work ... */ } EXPORT_SYMBOL_GPL(bar); /* This contains struct foo's definition */ #include "foo.h" int baz(struct foo *arg) { /* Do more work ... */ } EXPORT_SYMBOL_GPL(baz); Here, baz's CRC will be computed using the expansion of struct foo that was cached after bar's CRC calculation ('UNKOWN' here). But if EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded late, during baz's CRC calculation, which now has visibility over the full struct definition, hence resulting in a different CRC for baz. The proper fix for this certainly is in genksyms, but that will take me some time to get right. In the meantime, we have seen one occurrence of this in the ehci-hcd code which hits this problem because of the way it includes C files halfway through the code together with an unlucky mix of symbol trimming. In order to workaround this, move the include done in ehci-hub.c early in ehci-hcd.c, hence making sure the struct definitions are visible to the entire file. This improves CRC stability of the ehci-hcd exports even when symbol trimming is enabled. Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Quentin Perret <qperret@google.com> Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16usb: typec: intel_pmc_mux: Handle SCU IPC error conditionsMadhusudanarao Amara1-3/+9
Check and return if there are errors. The response bits are valid only on no errors. Fixes: b7404a29cd3d ("usb: typec: intel_pmc_mux: Definitions for response status bits") Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebookPenghao1-0/+4
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook. This notebook come with usb touchpad. And we would like to disable touchpad wakeup on this notebook by default. Signed-off-by: Penghao <penghao@uniontech.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16USB: UAS: fix disconnect by unplugging a hubOliver Neukum1-2/+12
The SCSI layer can go into an ugly loop if you ignore that a device is gone. You need to report an error in the command rather than in the return value of the queue method. We need to specifically check for ENODEV. The issue goes back to the introduction of the driver. Fixes: 115bb1ffa54c3 ("USB: Add UAS driver") Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16usb: typec: ucsi: Prevent mode overrunHeikki Krogerus1-6/+16
Sometimes the embedded controller firmware does not terminate the list of alternate modes that the partner supports in its response to the GET_ALTERNATE_MODES command. Instead the firmware returns the supported alternate modes over and over again until the driver stops requesting them. If that happens, the number of modes for each alternate mode will exceed the maximum 6 that is defined in the USB Power Delivery specification. Making sure that can't happen by adding a check for it. This fixes NULL pointer dereference that is caused by the overrun. Fixes: ad74b8649beaf ("usb: typec: ucsi: Preliminary support for alternate modes") Cc: stable@vger.kernel.org Reported-by: Zwane Mwaikambo <zwanem@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-16usb: typec: ucsi: acpi: Increase command completion timeout valueHeikki Krogerus1-1/+1
UCSI specification quite clearly states that if a command can't be completed in 10ms, the firmware must notify about BUSY condition. Unfortunately almost none of the platforms (the firmware on them) generate the BUSY notification even if a command can't be completed in time. The driver already considered that, and used a timeout value of 5 seconds, but processing especially the alternate mode discovery commands takes often considerable amount of time from the firmware, much more than the 5 seconds. That happens especially after bootup when devices are already connected to the USB Type-C connector. For now on those platforms the alternate mode discovery has simply failed because of the timeout. To improve the situation, increasing the timeout value for the command completion to 1 minute. That should give enough time for even the slowest firmware to process the commands. Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-08Merge tag 'usb-serial-5.9-rc5' of ↵Greg Kroah-Hartman3-8/+16
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for 5.9-rc5 Here are some new device ids for 5.9. All have been in linux-next with no reported issues. * tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: USB: serial: option: support dynamic Quectel USB compositions USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
2020-09-07usb: typec: intel_pmc_mux: Do not configure SBU and HSL Orientation in ↵Utkarsh Patel1-8/+0
Alternate modes According to the PMC Type C Subsystem (TCSS) Mux programming guide rev 0.7, bits 4 and 5 are reserved in Alternate modes. SBU Orientation and HSL Orientation needs to be configured only during initial cable detection in USB connect flow based on device property of "sbu-orientation" and "hsl-orientation". Configuring these reserved bits in the Alternate modes may result in delay in display link training or some unexpected behaviour. So do not configure them while issuing Alternate Mode requests. Fixes: ff4a30d5e243 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation") Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-07usb: typec: intel_pmc_mux: Do not configure Altmode HPD HighUtkarsh Patel1-4/+0
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev 0.7, bit 14 is reserved in Alternate mode. In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the status update command VDO is set to HPD_HIGH, HPD is configured via separate HPD mode request after configuring DP Alternate mode request. Configuring reserved bit may show unexpected behaviour. So do not configure them while issuing the Alternate Mode request. Fixes: 7990be48ef4d ("usb: typec: mux: intel: Handle alt mode HPD_HIGH") Cc: stable@vger.kernel.org Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04usb: core: fix slab-out-of-bounds Read in read_descriptorsZeng Tao1-0/+5
The USB device descriptor may get changed between two consecutive enumerations on the same device for some reason, such as DFU or malicius device. In that case, we may access the changing descriptor if we don't take the device lock here. The issue is reported: https://syzkaller.appspot.com/bug?id=901a0d9e6519ef8dc7acab25344bd287dd3c7be9 Cc: stable <stable@vger.kernel.org> Cc: Alan Stern <stern@rowland.harvard.edu> Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com Fixes: 217a9081d8e6 ("USB: add all configs to the "descriptors" attribute") Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com> Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04Revert "usb: dwc3: meson-g12a: fix shared reset control use"Amjad Ouled-Ameur1-9/+6
This reverts commit 7a410953d1fb4dbe91ffcfdee9cbbf889d19b0d7. This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting the change solves the issue. In fact, according to the reset framework code, consumers must not use reset_control_(de)assert() on shared reset lines when reset_control_reset has been used, and vice-versa. Moreover, with this commit, usb is not guaranted to be reset since the reset is likely to be initially deasserted. Reverting the commit will bring back the suspend warning mentioned in the commit description. Nevertheless, a warning is much less critical than breaking dwc3-meson-g12a USB completely. We will address the warning issue in another way as a 2nd step. Fixes: 7a410953d1fb ("usb: dwc3: meson-g12a: fix shared reset control use") Cc: stable <stable@vger.kernel.org> Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com> Reported-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04usb: typec: ucsi: acpi: Check the _DEP dependenciesHeikki Krogerus1-0/+4
Failing probe with -EPROBE_DEFER until all dependencies listed in the _DEP (Operation Region Dependencies) object have been met. This will fix an issue where on some platforms UCSI ACPI driver fails to probe because the address space handler for the operation region that the UCSI ACPI interface uses has not been loaded yet. Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04usb: typec: intel_pmc_mux: Un-register the USB role switchMadhusudanarao Amara1-0/+2
Added missing code for un-register USB role switch in the remove and error path. Cc: Stable <stable@vger.kernel.org> # v5.8 Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Fixes: 6701adfa9693b ("usb: typec: driver for Intel PMC mux control") Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com> Link: https://lore.kernel.org/r/20200825183811.7262-1-madhusudanarao.amara@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-04usb: Fix out of sync data toggle if a configured device is reconfiguredMathias Nyman1-49/+42
Userspace drivers that use a SetConfiguration() request to "lightweight" reset an already configured usb device might cause data toggles to get out of sync between the device and host, and the device becomes unusable. The xHCI host requires endpoints to be dropped and added back to reset the toggle. If USB core notices the new configuration is the same as the current active configuration it will avoid these extra steps by calling usb_reset_configuration() instead of usb_set_configuration(). A SetConfiguration() request will reset the device side data toggles. Make sure usb_reset_configuration() function also drops and adds back the endpoints to ensure data toggles are in sync. To avoid code duplication split the current usb_disable_device() function and reuse the endpoint specific part. Cc: stable <stable@vger.kernel.org> Tested-by: Martin Thierer <mthierer@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-31USB: serial: option: support dynamic Quectel USB compositionsBjørn Mork1-8/+12
The USB composition, defining the set of exported functions, is dynamic in newer Quectel modems. Default functions can be disabled and alternative functions can be enabled instead. The alternatives includes class functions using interface pairs, which should be handled by the respective class drivers. Active interfaces are numbered consecutively, so static blacklisting based on interface numbers will fail when the composition changes. An example of such an error, where the option driver has bound to the CDC ECM data interface, preventing cdc_ether from handling this function: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Quectel S: Product=EC25-AF C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 4 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00 I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 16 Ivl=32ms I:* If#= 5 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=option I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=option E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Another device with the same id gets correct drivers, since the interface of the network function happens to be blacklisted by option: T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0125 Rev= 3.18 S: Manufacturer=Android S: Product=Android C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Change rules for EC21, EC25, BG96 and EG95 to match vendor specific serial functions only, to prevent binding to class functions. Require 2 endpoints on ff/ff/ff functions, avoiding the 3 endpoint QMI/RMNET network functions. Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Sebastian Sjoholm <ssjoholm@mac.com> Cc: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-31USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modulesAleksander Morgado1-0/+2
These modules have 2 different USB layouts: The default layout with PID 0x9205 (AT+CUSBSELNV=1) exposes 4 TTYs and an ECM interface: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9205 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#=0x5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: AT-capable port (data). In the secondary layout with PID=0x9206 (AT+CUSBSELNV=86) the module exposes 6 TTY ports: T: Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1e0e ProdID=9206 Rev=00.00 S: Manufacturer=SimTech, Incorporated S: Product=SimTech SIM7080 S: SerialNumber=1234567890ABCDEF C: #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#=0x5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option The purpose of each TTY is as follows: * ttyUSB0: DIAG/QCDM port. * ttyUSB1: GNSS data. * ttyUSB2: AT-capable port (control). * ttyUSB3: QFLOG interface. * ttyUSB4: DAM interface. * ttyUSB5: AT-capable port (data). Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-30Merge tag 'usb-5.9-rc3' of ↵Linus Torvalds24-161/+376
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Let's try this again... Here are some USB fixes for 5.9-rc3. This differs from the previous pull request for this release in that the usb gadget patch now does not break some systems, and actually does what it was intended to do. Many thanks to Marek Szyprowski for quickly noticing and testing the patch from Andy Shevchenko to resolve this issue. Additionally, some more new USB quirks have been added to get some new devices to work properly based on user reports. Other than that, the patches are all here, and they contain: - usb gadget driver fixes - xhci driver fixes - typec fixes - new quirks and ids - fixes for USB patches that went into 5.9-rc1. All of these have been tested in linux-next with no reported issues" * tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) usb: storage: Add unusual_uas entry for Sony PSZ drives USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe() USB: gadget: u_f: Unbreak offset calculation in VLAs USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures USB: PHY: JZ4770: Fix static checker warning. USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb() USB: gadget: u_f: add overflow checks to VLA macros xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed xhci: Do warm-reset when both CAS and XDEV_RESUME are set usb: host: xhci: fix ep context print mismatch in debugfs usb: uas: Add quirk for PNY Pro Elite tools: usb: move to tools buildsystem USB: Fix device driver race USB: Also match device drivers using the ->match vfunc usb: host: xhci-tegra: fix tegra_xusb_get_phy() usb: host: xhci-tegra: otg usb2/usb3 port init usb: hcd: Fix use after free in usb_hcd_pci_remove() usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port() ...
2020-08-28usb: storage: Add unusual_uas entry for Sony PSZ drivesAlan Stern1-0/+7
The PSZ-HA* family of USB disk drives from Sony can't handle the REPORT OPCODES command when using the UAS protocol. This patch adds an appropriate quirks entry. Reported-and-tested-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27USB: Ignore UAS for JMicron JMS567 ATA/ATAPI BridgeCyril Roelandt1-1/+1
This device does not support UAS properly and a similar entry already exists in drivers/usb/storage/unusual_uas.h. Without this patch, storage_probe() defers the handling of this device to UAS, which cannot handle it either. Tested-by: Brice Goglin <brice.goglin@gmail.com> Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Cyril Roelandt <tipecaml@gmail.com> Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()Tang Bin1-3/+2
If the function platform_get_irq() failed, the negative value returned will not be detected here. So fix error handling in exynos_ohci_probe(). And when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here. Fixes: 62194244cf87 ("USB: Add Samsung Exynos OHCI diver") Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27USB: gadget: u_f: Unbreak offset calculation in VLAsAndy Shevchenko1-4/+4
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") makes VLA macros to always return 0 due to different scope of two variables of the same name. Obviously we need to have only one. Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Brooke Basile <brookebasile@gmail.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-27USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-DAlan Stern1-0/+5
The Sound Devices MixPre-D audio card suffers from the same defect as the Sound Devices USBPre2: an endpoint shared between a normal audio interface and a vendor-specific interface, in violation of the USB spec. Since the USB core now treats duplicated endpoints as bugs and ignores them, the audio endpoint isn't available and the card can't be used for audio capture. Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist duplicate ep on Sound Devices USBPre2"), this patch adds a quirks entry saying to ignore ep5in for interface 1, leaving it available for use with standard audio interface 2. Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints") Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA ↵Badhri Jagan Sridharan1-3/+25
2.3.1.2 failures The patch addresses the compliance test failures while running TDA 2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD Compliance MOI" test plan published in https://www.usb.org/usbc. For a product to be Type-C compliant, it's expected that these tests are run on usb.org certified Type-C compliance tester as mentioned in https://www.usb.org/usbc. While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that the static and dynamic electrical capabilities of a Source meet the requirements for each PDO offered, while doing so, the tests also monitor that the timing of the VBUS waveform versus the messages meets the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2. TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester Originated Hard Reset Purpose: To perform the appropriate protocol checks relating to any circumstance in which the Hard Reset signal is sent by the Tester. UUT is behaving as source: The Tester sends a Hard Reset signal. 1. Check VBUS stays within present valid voltage range for tPSHardReset min (25ms) after last bit of Hard Reset signal. [PROT_PROC_HR_TSTR_1] 2. Check that VBUS starts to fall below present valid voltage range by tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2] 3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms). [PROT_PROC_HR_TSTR_3] 4. Check that VBUS starts rising to vSafe5V after a delay of tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4] 5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery Compliance Plan 139 6. Check that Source Capabilities are finished sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v min. [PROT_PROC_HR_TSTR_6]. This is in line with 7.1.5 Response to Hard Resets of the USB Power Delivery Specification Revision 3.0, Version 1.2, "Hard Reset Signaling indicates a communication failure has occurred and the Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The USB connection May reset during a Hard Reset since the VBUS voltage will be less than vSafe5V for an extended period of time. After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V. A Source Shall conform to the VCONN timing as specified in [USB Type-C 1.3]." With the above guidelines from the spec in mind, TCPM does not turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of having VCONN on through hardreset. Also, the spec clearly states that "After establishing the vSafe0V voltage condition on VBUS", the Source Shall wait tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V. TCPM does not conform to this requirement. If the TCPC driver calls tcpm_vbus_change with vbus off signal, TCPM right away enters SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover. For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM assumes that the vsafe0v is instantaneous as TCPM only waits tSrcRecover instead of waiting for tSafe0v + tSrcRecover. This patch also fixes this behavior by making sure that TCPM waits for tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when tcpm_vbus_change is called by TCPC. When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case i.e. tSafe0v + tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON. Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25USB: PHY: JZ4770: Fix static checker warning.周琰杰 (Zhou Yanjie)1-0/+1
The commit 2a6c0b82e651 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.") introduced the initialization function for different chips, but left the relevant code involved in the resetting process in the original function, resulting in uninitialized variable calls. Fixes: 2a6c0b82e651 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs."). Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()Brooke Basile1-12/+69
Some values extracted by ncm_unwrap_ntb() could possibly lead to several different out of bounds reads of memory. Specifically the values passed to netdev_alloc_skb_ip_align() need to be checked so that memory is not overflowed. Resolve this by applying bounds checking to a number of different indexes and lengths of the structure parsing logic. Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-25USB: gadget: u_f: add overflow checks to VLA macrosBrooke Basile1-11/+27
size can potentially hold an overflowed value if its assigned expression is left unchecked, leading to a smaller than needed allocation when vla_group_size() is used by callers to allocate memory. To fix this, add a test for saturation before declaring variables and an overflow check to (n) * sizeof(type). If the expression results in overflow, vla_group_size() will return SIZE_MAX. Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Suggested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-24USB: serial: ftdi_sio: add IDs for Xsens Mti USB converterPatrick Riphagen2-0/+2
The device added has an FTDI chip inside. The device is used to connect Xsens USB Motion Trackers. Cc: stable@vger.kernel.org Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com> Signed-off-by: Johan Hovold <johan@kernel.org>
2020-08-24treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva25-42/+41
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2020-08-23xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failedDing Hui1-1/+2
Some device drivers call libusb_clear_halt when target ep queue is not empty. (eg. spice client connected to qemu for usb redir) Before commit f5249461b504 ("xhci: Clear the host side toggle manually when endpoint is soft reset"), that works well. But now, we got the error log: EP not empty, refuse reset xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE bit still set So all the subsequent urb sumbits to the ep will fail with the warn log: Can't enqueue URB while manually clearing toggle We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after xhci_endpoint_reset, even if it failed. Fixes: f5249461b504 ("xhci: Clear the host side toggle manually when endpoint is soft reset") Cc: stable <stable@vger.kernel.org> # v4.17+ Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-23xhci: Do warm-reset when both CAS and XDEV_RESUME are setKai-Heng Feng1-9/+10
Sometimes re-plugging a USB device during system sleep renders the device useless: [ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262 ... [ 176.496485] usb 2-4: Waited 2000ms for CONNECT [ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19 [ 176.497103] usb 2-4: can't resume, status -19 [ 176.497438] usb usb2-port4: logical disconnect Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore, despite of CAS bit is flagged. So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for the port. Cc: stable <stable@vger.kernel.org> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-23usb: host: xhci: fix ep context print mismatch in debugfsLi Jun1-4/+4
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get the ep context. [rename dci to ep_index -Mathias] Cc: stable <stable@vger.kernel.org> # v4.15+ Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver") Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-19usb: uas: Add quirk for PNY Pro EliteThinh Nguyen1-0/+7
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12 pass-through command (i.e. it just hangs). If it doesn't support this command, it should respond properly to the host. Let's just add a quirk to be able to move forward with other operations. Cc: stable@vger.kernel.org Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-19Merge tag 'fixes-for-v5.9-rc2' of ↵Greg Kroah-Hartman2-21/+93
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus Felipe writes: USB: fixes for v5.9-rc Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget Signed-off-by: Felipe Balbi <balbi@kernel.org> * tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: usb: dwc3: gadget: Handle ZLP for sg requests usb: dwc3: gadget: Fix handling ZLP usb: dwc3: gadget: Don't setup more than requested usb: gadget: f_tcm: Fix some resource leaks in some error paths
2020-08-18USB: Fix device driver raceBastien Nocera1-2/+38
When a new device with a specialised device driver is plugged in, the new driver will be modprobe()'d but the driver core will attach the "generic" driver to the device. After that, nothing will trigger a reprobe when the modprobe()'d device driver has finished initialising, as the device has the "generic" driver attached to it. Trigger a reprobe ourselves when new specialised drivers get registered. Fixes: 88b7381a939d ("USB: Select better matching USB drivers when available") Signed-off-by: Bastien Nocera <hadess@hadess.net> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18USB: Also match device drivers using the ->match vfuncBastien Nocera1-2/+3
We only ever used the ID table matching before, but we should also support open-coded match functions. Fixes: 88b7381a939de ("USB: Select better matching USB drivers when available") Signed-off-by: Bastien Nocera <hadess@hadess.net> Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200818110445.509668-1-hadess@hadess.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: host: xhci-tegra: fix tegra_xusb_get_phy()JC Kuo1-1/+1
tegra_xusb_get_phy() should take input argument "name". Signed-off-by: JC Kuo <jckuo@nvidia.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200811092553.657762-1-jckuo@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: host: xhci-tegra: otg usb2/usb3 port initJC Kuo1-0/+2
tegra_xusb_init_usb_phy() should initialize "otg_usb2_port" and "otg_usb3_port" with -EINVAL because "0" is a valid value represents usb2 port 0 or usb3 port 0. Signed-off-by: JC Kuo <jckuo@nvidia.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200811093143.699541-1-jckuo@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: hcd: Fix use after free in usb_hcd_pci_remove()Andy Shevchenko1-1/+4
On the removal stage we put a reference to the controller structure and if it's not used anymore it gets freed, but later we try to dereference a pointer to a member of that structure. Copy necessary field to a temporary variable to avoid use after free. Fixes: 306c54d0edb6 ("usb: hcd: Try MSI interrupts on PCI devices") Reported-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/linux-usb/30a8c4ca-64c2-863b-cfcd-0970599c0ba3@huawei.com/ Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200814182218.71957-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()Hans de Goede2-17/+23
Commit 081da1325d35 ("usb: typec: ucsi: displayport: Fix a potential race during registration") made the ucsi code hold con->lock in ucsi_register_displayport(). But we really don't want any interactions with the connector to run before the port-registration process is fully complete. This commit moves the taking of con->lock from ucsi_register_displayport() into ucsi_register_port() to achieve this. Cc: stable@vger.kernel.org Fixes: 081da1325d35 ("usb: typec: ucsi: displayport: Fix a potential race during registration") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: typec: ucsi: Rework ppm_lock handlingHans de Goede1-34/+22
The ppm_lock really only needs to be hold during 2 functions: ucsi_reset_ppm() and ucsi_run_command(). Push the taking of the lock down into these 2 functions, renaming ucsi_run_command() to ucsi_send_command() which was an existing wrapper already taking the lock for its callers. This simplifies things for the callers and removes the difference between ucsi_send_command() and ucsi_run_command() which has led to various locking bugs in the past. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: typec: ucsi: Fix 2 unlocked ucsi_run_command callsHans de Goede1-2/+4
Fix 2 unlocked ucsi_run_command calls: 1. ucsi_handle_connector_change() contains one ucsi_send_command() call, which takes the ppm_lock for it; and one ucsi_run_command() call which relies on the caller have taking the ppm_lock. ucsi_handle_connector_change() does not take the lock, so the second (ucsi_run_command) calls should also be ucsi_send_command(). 2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which does not hold the ppm_lock, so it also must use ucsi_send_command(). This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to ucsi_run_command() to avoid similar problems getting re-introduced in the future. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: typec: ucsi: Fix AB BA lock inversionHans de Goede1-9/+9
Lockdep reports an AB BA lock inversion between ucsi_init() and ucsi_handle_connector_change(): AB order: 1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the duration of the function) 2. usci_init eventually end up calling ucsi_register_displayport, which takes ucsi_connector->lock BA order: 1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock 2. ucsi_handle_connector_change calls ucsi_send_command which takes ucsi->ppm_lock The ppm_lock really only needs to be hold during 2 functions: ucsi_reset_ppm() and ucsi_run_command(). This commit fixes the AB BA lock inversion by making ucsi_init drop the ucsi->ppm_lock before it starts registering ports; and replacing any ucsi_run_command() calls after this point with ucsi_send_command() (which is a wrapper around run_command taking the lock while handling the command). Some of the replacing of ucsi_run_command with ucsi_send_command in the helpers used during port registration also fixes a number of code paths after registration which call ucsi_run_command() without holding the ppm_lock: 1. ucsi_altmode_update_active() call in ucsi/displayport.c 2. ucsi_register_altmodes() call from ucsi_handle_connector_change() (through ucsi_partner_change()) Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usbip: Implement a match function to fix usbipM. Vefa Bicakci1-0/+6
Commit 88b7381a939d ("USB: Select better matching USB drivers when available") introduced the use of a "match" function to select a non-generic/better driver for a particular USB device. This unfortunately breaks the operation of usbip in general, as reported in the kernel bugzilla with bug 208267 (linked below). Upon inspecting the aforementioned commit, one can observe that the original code in the usb_device_match function used to return 1 unconditionally, but the aforementioned commit makes the usb_device_match function use identifier tables and "match" virtual functions, if either of them are available. Hence, this commit implements a match function for usbip that unconditionally returns true to ensure that usbip is functional again. This change has been verified to restore usbip functionality, with a v5.7.y kernel on an up-to-date version of Qubes OS 4.0, which uses usbip to redirect USB devices between VMs. Thanks to Jonathan Dieter for the effort in bisecting this issue down to the aforementioned commit. Fixes: 88b7381a939d ("USB: Select better matching USB drivers when available") Link: https://bugzilla.kernel.org/show_bug.cgi?id=208267 Link: https://bugzilla.redhat.com/show_bug.cgi?id=1856443 Link: https://github.com/QubesOS/qubes-issues/issues/5905 Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com> Cc: <stable@vger.kernel.org> # 5.7 Cc: Valentina Manea <valentina.manea.m@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Bastien Nocera <hadess@hadess.net> Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20200810160017.46002-1-m.v.b@runbox.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18usb: renesas-xhci: remove version checkVinod Koul1-18/+1
Some devices in wild are reporting bunch of firmware versions, so remove the check for versions in driver Reported by: Anastasios Vacharakis <vacharakis@gmail.com> Reported by: Glen Journeay <journeay@gmail.com> Fixes: 2478be82de44 ("usb: renesas-xhci: Add ROM loader for uPD720201") Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208911 Signed-off-by: Vinod Koul <vkoul@kernel.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200818071739.789720-1-vkoul@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18USB: lvtest: return proper error code in probeEvgeny Novikov1-1/+1
lvs_rh_probe() can return some nonnegative value from usb_control_msg() when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as a failure. Make lvs_rh_probe() return -EINVAL in this case. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Evgeny Novikov <novikov@ispras.ru> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200805090643.3432-1-novikov@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18USB: cdc-acm: rework notification_buffer resizingTom Rix1-12/+10
Clang static analysis reports this error cdc-acm.c:409:3: warning: Use of memory after it is freed acm_process_notification(acm, (unsigned char *)dr); There are three problems, the first one is that dr is not reset The variable dr is set with if (acm->nb_index) dr = (struct usb_cdc_notification *)acm->notification_buffer; But if the notification_buffer is too small it is resized with if (acm->nb_size) { kfree(acm->notification_buffer); acm->nb_size = 0; } alloc_size = roundup_pow_of_two(expected_size); /* * kmalloc ensures a valid notification_buffer after a * use of kfree in case the previous allocation was too * small. Final freeing is done on disconnect. */ acm->notification_buffer = kmalloc(alloc_size, GFP_ATOMIC); dr should point to the new acm->notification_buffer. The second problem is any data in the notification_buffer is lost when the pointer is freed. In the normal case, the current data is accumulated in the notification_buffer here. memcpy(&acm->notification_buffer[acm->nb_index], urb->transfer_buffer, copy_size); When a resize happens, anything before notification_buffer[acm->nb_index] is garbage. The third problem is the acm->nb_index is not reset on a resizing buffer error. So switch resizing to using krealloc and reassign dr and reset nb_index. Fixes: ea2583529cd1 ("cdc-acm: reassemble fragmented notifications") Signed-off-by: Tom Rix <trix@redhat.com> Cc: stable <stable@vger.kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18USB: quirks: Add no-lpm quirk for another Raydium touchscreenKai-Heng Feng1-0/+2
There's another Raydium touchscreen needs the no-lpm quirk: [ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00 [ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.339151] usb 1-9: Product: Raydium Touch System [ 1.339152] usb 1-9: Manufacturer: Raydium Corporation ... [ 6.450497] usb 1-9: can't set config #1, error -110 BugLink: https://bugs.launchpad.net/bugs/1889446 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200731051622.28643-1-kai.heng.feng@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18USB: yurex: Fix bad gfp argumentAlan Stern1-1/+1
The syzbot fuzzer identified a bug in the yurex driver: It passes GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING: do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000370c7c68>] prepare_to_wait+0xb1/0x2a0 kernel/sched/wait.c:247 WARNING: CPU: 1 PID: 340 at kernel/sched/core.c:7253 __might_sleep+0x135/0x190 kernel/sched/core.c:7253 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 340 Comm: syz-executor677 Not tainted 5.8.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xf6/0x16e lib/dump_stack.c:118 panic+0x2aa/0x6e1 kernel/panic.c:231 __warn.cold+0x20/0x50 kernel/panic.c:600 report_bug+0x1bd/0x210 lib/bug.c:198 handle_bug+0x41/0x80 arch/x86/kernel/traps.c:234 exc_invalid_op+0x14/0x40 arch/x86/kernel/traps.c:254 asm_exc_invalid_op+0x12/0x20 arch/x86/include/asm/idtentry.h:536 RIP: 0010:__might_sleep+0x135/0x190 kernel/sched/core.c:7253 Code: 65 48 8b 1c 25 40 ef 01 00 48 8d 7b 10 48 89 fe 48 c1 ee 03 80 3c 06 00 75 2b 48 8b 73 10 48 c7 c7 e0 9e 06 86 e8 ed 12 f6 ff <0f> 0b e9 46 ff ff ff e8 1f b2 4b 00 e9 29 ff ff ff e8 15 b2 4b 00 RSP: 0018:ffff8881cdb77a28 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff8881c6458000 RCX: 0000000000000000 RDX: ffff8881c6458000 RSI: ffffffff8129ec93 RDI: ffffed1039b6ef37 RBP: ffffffff86fdade2 R08: 0000000000000001 R09: ffff8881db32f54f R10: 0000000000000000 R11: 0000000030343354 R12: 00000000000001f2 R13: 0000000000000000 R14: 0000000000000068 R15: ffffffff83c1b1aa slab_pre_alloc_hook.constprop.0+0xea/0x200 mm/slab.h:498 slab_alloc_node mm/slub.c:2816 [inline] slab_alloc mm/slub.c:2900 [inline] kmem_cache_alloc_trace+0x46/0x220 mm/slub.c:2917 kmalloc include/linux/slab.h:554 [inline] dummy_urb_enqueue+0x7a/0x880 drivers/usb/gadget/udc/dummy_hcd.c:1251 usb_hcd_submit_urb+0x2b2/0x22d0 drivers/usb/core/hcd.c:1547 usb_submit_urb+0xb4e/0x13e0 drivers/usb/core/urb.c:570 yurex_write+0x3ea/0x820 drivers/usb/misc/yurex.c:495 This patch changes the call to use GFP_ATOMIC instead of GFP_KERNEL. Reported-and-tested-by: syzbot+c2c3302f9c601a4b1be2@syzkaller.appspotmail.com Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810182954.GB307778@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-17usb: dwc3: gadget: Handle ZLP for sg requestsThinh Nguyen1-0/+31
Currently dwc3 doesn't handle usb_request->zero for SG requests. This change checks and prepares extra TRBs for the ZLP for SG requests. Cc: <stable@vger.kernel.org> # v4.5+ Fixes: 04c03d10e507 ("usb: dwc3: gadget: handle request->zero") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>