| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719a5 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allwinner A64 EHCI requires 4 clocks to be enabled.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)
The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.
It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).
There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dynamic debugging will already add the function (and the line number)
to a debug message if one requests that. It makes no sense to add
them unconditionally in a driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.8-rc2
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc1
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
|
|
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
block any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the correct response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
[AmitP: Cherry-picked this patch and folded other relevant
fixes from Android common kernel android-4.4]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The udc device needs to be deleted if error occurs
Fixes: 855ed04a3758 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=.
Fixes: 3948f0e0c999 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix io submissions failing with ENODEV.
Signed-off-by: Mathieu Laurendeau <mat.lau@laposte.net>
Fixes: 7fe3976e0f3a ("gadget: switch ep_io_operations to ->read_iter/->write_iter")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In 'composite_os_desc_req_prepare', if one of the memory allocations fail,
0 will be returned, which means success.
We should return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If this memory allocation fail, we will return 0, which means success.
Return -ENOMEM instead.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When reading synchronously from a non-zero endpoint, gadgetfs will
return -EFAULT even if the read succeeds, due to a bad check of the
copy_to_iter() return value.
This fix compares the return value of copy_to_iter to the amount of
bytes that was passed, and only fails if they are not the same.
Signed-off-by: Binyamin Sharet <s.binyamin@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc705 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add missing platform_set_drvdata() in omap_otg_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There may be a race condition if f_fs calls unregister_gadget_item in
ffs_closed() when unregister_gadget is called by UDC store at the same time.
this leads to a kernel NULL pointer dereference:
[ 310.644928] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 310.645053] init: Service 'adbd' is being killed...
[ 310.658938] pgd = c9528000
[ 310.662515] [00000004] *pgd=19451831, *pte=00000000, *ppte=00000000
[ 310.669702] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 310.675211] Modules linked in:
[ 310.678294] CPU: 0 PID: 1537 Comm: ->transport Not tainted 4.1.15-03725-g793404c #2
[ 310.685958] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 310.692493] task: c8e24200 ti: c945e000 task.ti: c945e000
[ 310.697911] PC is at usb_gadget_unregister_driver+0xb4/0xd0
[ 310.703502] LR is at __mutex_lock_slowpath+0x10c/0x16c
[ 310.708648] pc : [<c075efc0>] lr : [<c0bfb0bc>] psr: 600f0113
<snip..>
[ 311.565585] [<c075efc0>] (usb_gadget_unregister_driver) from [<c075e2b8>] (unregister_gadget_item+0x1c/0x34)
[ 311.575426] [<c075e2b8>] (unregister_gadget_item) from [<c076fcc8>] (ffs_closed+0x8c/0x9c)
[ 311.583702] [<c076fcc8>] (ffs_closed) from [<c07736b8>] (ffs_data_reset+0xc/0xa0)
[ 311.591194] [<c07736b8>] (ffs_data_reset) from [<c07738ac>] (ffs_data_closed+0x90/0xd0)
[ 311.599208] [<c07738ac>] (ffs_data_closed) from [<c07738f8>] (ffs_ep0_release+0xc/0x14)
[ 311.607224] [<c07738f8>] (ffs_ep0_release) from [<c023e030>] (__fput+0x80/0x1d0)
[ 311.614635] [<c023e030>] (__fput) from [<c014e688>] (task_work_run+0xb0/0xe8)
[ 311.621788] [<c014e688>] (task_work_run) from [<c010afdc>] (do_work_pending+0x7c/0xa4)
[ 311.629718] [<c010afdc>] (do_work_pending) from [<c010770c>] (work_pending+0xc/0x20)
for functions using functionFS, i.e. android adbd will close /dev/usb-ffs/adb/ep0
when usb IO thread fails, but switch adb from on to off also triggers write
"none" > UDC. These 2 operations both call unregister_gadget, which will lead
to the panic above.
add a mutex before calling unregister_gadget for api used in f_fs.
Signed-off-by: Winter Wang <wente.wang@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
dev->port_usb is checked for null pointer at above code, so dev->port_usb
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
cdev->config is checked for null pointer at above code, so cdev->config
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.
Fixes: 6e4b74e4690d ("usb: renesas: fix scheduling in atomic context bug")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -16
This issue causes the followings:
1) A pipe is enabled as transmission
2) The pipe sent a data
3) The pipe is disabled and re-enabled as reception.
4) The pipe got a queue
Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.
Cc: <stable@vger.kernel.org> # v4.1+ (usbhs_xxxsts_clear() is needed)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
