| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
loss,SCSI_MLQUEUE_DEVICE_BUSY if device is busy
1 Its observed that the OS was sending request to the driver after it had been
put into blocking state, so the driver was modified to return
SCSI_MLQUEUE_DEVICE_BUSY.
2. Driver will return DID_TRANSPORT_DISRUPTED when sdev is haivng nexus loss.
This occurrs when sdev is blocked, between the
MPI2_EVENT_SAS_TOPO_RC_DELAY_NOT_RESPONDING and
MPI2_EVENT_SAS_TOPO_RC_TARG_NOT_RESPONDING events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
READY state
The driver needs to retrieve the ioc facts prior to putting the controller
into READY state. The current design is calling ioc facts after putting the
controller into READY state, which means the driver is sending a diag reset
instead of message unit reset becuase the capability information is not yet
available.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
(1) for the MPI2_EVENT_IR_OPERATION_STATUS event, add support to print
"background init" or "make data consistent" for debugging purposes. If the
RAIDOperation is set to a value not defined, then don't print anything
(2) for the MPI2_EVENT_SAS_DEVICE_STATUS_CHANGE event, add support to print
"expander reduced functionality" and "expander reduced functionality
complete", which are new events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
part of volume
Added sanity check in _scsih_change_queue_depth to limit the max_depth to 32
for SATA devices. This is only for physical devices not part of a volume.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added support to set the TimeStamp when sending ioc_init.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added tests for registry entries of EXBuffSize, EXImmed, and EXType to
support the new Extended diag buffer type. Modified code where necessary to
handle the new ExtendedType field in the F/W diagnostic Post and Release
messages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added command line option diag_buffer_enable. When the command line option is
set, the driver will automatically post diag buffers at driver load time.
The command line option diag_buffer_enable is bitwise, so it's possible to
enable both and/or snapshot + trace buffers. For trace, the driver will
allocate 1MB buffer, whereas for snapshot its 2MB. The purpose for this is
so the enduser doesn't have to manually use an application to setup diag
buffers for debugging firmware related issues.
Here is some examples
trace:
# insmod mpt2sas.ko diag_buffer_enable=1
snapshot:
# insmod mpt2sas.ko diag_buffer_enable=2
both trace and snapshot:
# insmod mpt2sas.ko diag_buffer_enable=3
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Fixed some of the comments sections for some of the function so "@ioc:
pointer to scsi command object" was changed to "@ioc: per adapter object"
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added command line option and shost sysfs attribute called
mpt2sas_fwfault_debug. When enduser writes a "1" to this parameter, this
will enable support in the driver for debugging firmware timeout related
issues. This handling was added in three areas (a) scsi error handling
callback called task_abort, (b) IOCTL interface, and (c) other timeouts that
result in diag resets, such as manufacturing config pages. When this
support is enabled, the driver will provide dump_stack to console, halt
controller firmware, and panic driver. The end user probably would want to
setup serial console redirection so the dump stack can be seen.
Here are the three methods for enable this support:
(a) # insmod mpt2sas.ko mpt2sas_fwfault_debug=1
(b) # echo 1 > /sys/module/mpt2sas/parameters/mpt2sas_fwfault_debug
(c) # echo 1 > /sys/class/scsi_host/host#/fwfault_debug (where # is
the host number)
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The new headers contain the following changes:
(1) Added IO Unit Page 7.
(2) Added new device ids for SAS2208.
(3) Added SAS IO Unit Page 5.
(4) Added partial and slumber power management capable flags to SAS Device
Page 0 Flags field.
(5) Added PhyInfo defines for power condition.
(6) Added Ethernet configuration pages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added device ids range for { 0x80 - 87 } , modified mpi/mpi2_cnfg.h containing
MPI2_MFGPAGE_DEVID_SAS2208_X.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support in the driver to check for valid response info in the scsi
state, then check to see if the response code is
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME; when this condition occurrs, the driver
will return DID_SOFT_ERROR. A return code of DID_SOFT_ERROR will result in
a retry at the scsi-mid layer level. An additional change added to obtain
the response code from the 1st byte of the response info instead of last.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
add.
This handles the case where driver receives a expander removal event while
it is in the middle of processing an expander add event. The existing
implementation will stop processing futher device adds when a expander
delete arrives on top of add expander add. Due to a sanity check in the
driver, the devices there were not added, were never handshaked to firmware
with the device removal handshake protocal. Since the driver didnt' do the
handshake, the controller never provide further add events. To fix this
issue, the sanity check was removed so the driver will always do the device
removal handshake protocal.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The device driver was not handling updating device handles in all cases
across diag resets. To fix this issue, the driver is converted to using sas
address instead of handle as a lookup reference to the parent expander or
sas_host. Also, for both expanders and sas host, the phy handle will be one
unique handle. In the sas host case, the phy handle can be different for
every phy, so the change is to set the handle to the handle of the first
phy; every phy will be one single sas address(phy 0) instead of a different
sas address for every phy(previous implementation). So making one consistent
sas address for all the direct attachedports to the sas host, will make it
better user experience when using udev /dev/disk/by-path dev nodes
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] zfcp: Flush SCSI registration work when adding unit
[SCSI] zfcp: Fix timer initialization for ct and els requests
[SCSI] zfcp: Warn about storage devices with broken PLOGI data
[SCSI] zfcp: Handle WWPN mismatch in PLOGI payload
[SCSI] zfcp: fix kfree handling in zfcp_init_device_setup
[SCSI] fix memory leak in initialization
|
|
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The root cause of the problem is the fact that dev_set_name() now
allocates storage instead of using the original array within the kobj.
That means that the SCSI assumption that if you haven't made the
containing object or any sub objects visible, you can just destroy it
(and its component devices) lock stock and barrel becomes false.
Fix this by doing the get of sdev_dev at parent time and thus do an
extra put of it in scsi_destroy_sdev() (and all other destruction
without add paths).
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (34 commits)
[SCSI] qla2xxx: Fix NULL ptr deref bug in fail path during queue create
[SCSI] st: fix possible memory use after free after MTSETBLK ioctl
[SCSI] be2iscsi: Moving to pci_pools v3
[SCSI] libiscsi: iscsi_session_setup to allow for private space
[SCSI] be2iscsi: add 10Gbps iSCSI - BladeEngine 2 driver
[SCSI] zfcp: Fix hang when offlining device with offline chpid
[SCSI] zfcp: Fix lockdep warning when offlining device with offline chpid
[SCSI] zfcp: Fix oops during shutdown of offline device
[SCSI] zfcp: Fix initial device and cfdc for delayed adapter allocation
[SCSI] zfcp: correctly initialize unchained requests
[SCSI] mpt2sas: Bump version 02.100.03.00
[SCSI] mpt2sas: Support dev remove when phy status is MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
[SCSI] mpt2sas: Timeout occurred within the HANDSHAKE logic while waiting on firmware to ACK.
[SCSI] mpt2sas: Call init_completion on a per request basis.
[SCSI] mpt2sas: Target Reset will be issued from Interrupt context.
[SCSI] mpt2sas: Added SCSIIO, Internal and high priority memory pools to support multiple TM
[SCSI] mpt2sas: Copyright change to 2009.
[SCSI] mpt2sas: Added mpi2_history.txt for MPI2 headers.
[SCSI] mpt2sas: Update driver to MPI2 REV K headers.
[SCSI] bfa: Brocade BFA FC SCSI driver
...
|
|
Current code attempts to clean up resources when queue create fails and there it
invokes queue free call with a (NULL) pointer to the queue which could not be
allocated in the first place. Fix it by returning directly without invoking the
queue free call as no resources has been allocated at that point of time.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
A memory use after free bug can manifest if the MTSETBLK or SET_DENS_AND_BLK
ioctl features are used to set the tape's blocksize from 0 to non-zero.
After the driver sets the new block size, in this one case it calls
normalize_buffer() to free the device's internal data buffers. However, the
ioctl code assumes there is always a buffer and does not check or allocate
a buffer if there isn't one. So any following ioctl calls can corrupt
a part of memory by writing data to memory that the st driver had freed.
This patch removes the normalize_buffer() call and the specialness of
changing from a 0 to non-zero blocksize to fix the possible use of
memory after it has been freed by the st driver.
signed-off-by: David Jeffery <djeffery@redhat.com>
Acked-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch contains changes to use pci_pools for iscsi hdr
instead of pci_alloc_consistent. Here we alloc and free to pool
for every IO
v3:
- Remove cleanup loop in beiscsi_session_destroy
- Fixup for allocation failure handling in beiscsi_alloc_pdu
- Removed unused variable in beiscsi_session_destroy.
[jejb: fix up pci_pool_alloc address sizing problem]
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
[v2: fixed up virt_to_bus() issue spotted by sfr]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Bump version to 02.100.03.00
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
Add support to process device removal events when the phy status is set to
MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
firmware to ACK.
Following a diag_reset, a request to send an ioc_init is timing out. The
timeout occurred within the HANDSHAKE logic while waiting on firmware to
acknowledge that the driver had wrote to the doorbell register. This was
root caused to a logic timeout in the firmware code. The proposed solution
is for the driver to call the udelay instead of msleep API in function where
its looping reading the interrupt status. In addition to this change, there
were two additional cases where we deleted the clearing interrupt status
outside handshake context.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Now driver call init_completion on a per request basis. At some
point the wait_for_completion_timeout is not waiting for the timeout,
instead returning immediately, thus going into diag reset. This fix will
address all request using the wait_for_completion_timeout API. The previous
implimentation was only calling init_completion at driver
load time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
(1) Added three new functions to handle sending target resest and OP_REMOVE
from interrupt time, they are _scsih_tm_tr_send, _scsih_tm_tr_complete, and
_scsih_sas_control_complete. This code will create a link list of pending
target resets if there is no more available request in the hipriority
request queue. The list is stored in ioc->delayed_tr_list.
(2) All callback handler return type is changed from void to u8.
Now _base_interrupt will check for return type of callback handlers to
take decision of message frame is already freed or not.
In genral,
Return 1 meaning mf should be freed from _base_interrupt
0 means the mf is freed from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
support multiple TM
1) create a pool of high priority message frames in the region of memory
between message frames and chains. The modifications are in
_base_allocate_memory_pools. Also create a seperate pool of memory for
internal commands located near the same region of memory. The pool of high
priority message frames is restriced by the facts->HighPriorityCredit.
2) Create additional API for accessing request message frames. New function
mpt2sas_base_get_smid_hpr is for highpriority request. New function
mpt2sas_base_get_smid_scsiio for SCSI_IO, passing in the scsi command
pointer. The mpt2sas_base_get_smid function is for requesting internal
commands.
3) Added new function _base_get_cb_idx to obtain the callback
index from one of the three pools of request message frames.
4) Removed wrapper functions _scsih_scsi_lookup_set and
_scsih_scsi_lookup_getclear. These were removed because this handling was
moved into mpt2sas_base_get_smid_scsiio and mpt2sas_base_free_smid.
5) The function mpt2sas_base_free_smid is modified so the request message
frames are put back on one of the three pools of request message frames.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Update the copyright year to 2009 through out the code.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Added new file for MPI2 header version history.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Drivers header are updated to the MPI2 REV K headers.
Renamed VF_ID to msix_index in all call back handlers.
VF_ID is removed from all request descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add new driver for Brocade Hardware
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add missing kernel-doc notation in scsi_transport_fc.c:
Warning(drivers/scsi/scsi_transport_fc.c:3593): No description found for parameter 'q'
Warning(drivers/scsi/scsi_transport_fc.c:3700): No description found for parameter 'q'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Add support for 32-byte READ/WRITE as well as DIF Type 2 protection.
Reject protected 10/12/16 byte READ/WRITE commands when Type 2 is
enabled.
Verify Type 2 reference tag according to Expected Initial LBA in 32-byte
CDB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled. Only the 32-byte variants are supported.
Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
We would leak a scsi_data_buffer if the free_list command was of the
protected variety.
Reported-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled. However, communication between initiator and target should be
independent of protection information DMA. There are DIF-only host
adapters coming out that will be able to take advantage of this.
Move the relevant DIF bits to sd.c.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not. It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.
Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation. Update sd_dif and lpfc
accordingly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Ihab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
A target reset when I/O is ongoing might result
an eventual device offline, as scsi_eh_completed_normally()
might return ADD_TO_MLQUEUE in addition to the
advertised SUCCESS, FAILED, and NEEDS_RETRY.
Which is unfortunate as scsi_send_eh_cmnd() will
therefore map ADD_TO_MLQUEUE to FAILED instead of
the more appropriate NEEDS_RETRY.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Running sg_luns on s390x with CONFIG_DEBUG_PAGEALLOC enabled fails
with EFAULT from the SG_IO ioctl. The EFAULT is the result from
copy_to_user failing in this call chain:
sg_ioctl
sg_new_read
sg_finish_rem_req
blk_rq_unmap_user
__blk_rq_unmap_user
bio_uncopy_user
__bio_copy_iov
copy_to_user
The sg driver calls sg_remove_scat to free the memory pages before
calling blk_rq_unmap_user that tries to copy the data back to
userspace. Change the order to first call blk_rq_unmap_user before
freeing the pages in sg_remove_scat.
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: stable@kernel.org
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
On certain cases, UDF disc doesn't report capacity correctly via
READ_CAPACITY but TOC or trackinfo contains valid information which
can be obtained using cdrom_get_last_written(). ide-cd considers both
values and uses the larger one. Do the same in sr. This fixes
bko#9668.
http://bugzilla.kernel.org/show_bug.cgi?id=9668
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
5706/5708/5709 devices allow driver/user to set page size. By default it is
set to 4096. Current drivers do not program this register based on
architecture type (e.g. x86 = 4K, IA64 = 16K) and by choice lets device use
the defaults. So while mapping connection context memory (doorebll registers),
driver has to match page size used by the device. Included change fixes the
issue we uncovered during IA64 testing
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Most code changes were made to support RR44xx adapters.
- add more PCI device ID.
- using PCI BAR[2] to access RR44xx IOP.
- using PCI BAR[0] to check and clear RR44xx IRQ.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The function mode_select_handle_sense returns SCSI_DH_OK even when there is a sense code which is incorrect. Removing it so that it returns SCSI_DH_IO when there is sense that is not handled by this function.
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Reviewed-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: Bob Stankey <Robert.stankey@lsi.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
1.Changed driver prints to use scmd_printk, sdev_printk
2.Changed dev_err calls to scmd_printk for scsi related print messages
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This is support for Areca SAS/SATA HBA, ARC-1300/1320, which quipped with
88SE6440/88SE9480 respectively.
Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw >
Cc: Ke Wei <kewei.mv@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
[akpm@linux-foundation.org: fix KVM]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
