| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 699ca30162686bf305cdf94861be02eb0cf9bda2 ]
If __get_free_pages() fails, return -ENOMEM to avoid a NULL pointer
dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 954b4b752a4c4e963b017ed8cef4c453c5ed308d ]
The MSI message address in the RC address space can be 64 bit. The
R-Car PCIe RC supports such a 64bit MSI message address as well.
The code currently uses virt_to_phys(__get_free_pages()) to obtain
a reserved page for the MSI message address, and the return value
of which can be a 64 bit physical address on 64 bit system.
However, the driver only programs PCIEMSIALR register with the bottom
32 bits of the virt_to_phys(__get_free_pages()) return value and does
not program the top 32 bits into PCIEMSIAUR, but rather programs the
PCIEMSIAUR register with 0x0. This worked fine on older 32 bit R-Car
SoCs, however may fail on new 64 bit R-Car SoCs.
Since from a PCIe controller perspective, an inbound MSI is a memory
write to a special address (in case of this controller, defined by
the value in PCIEMSIAUR:PCIEMSIALR), which triggers an interrupt, but
never hits the DRAM _and_ because allocation of an MSI by a PCIe card
driver obtains the MSI message address by reading PCIEMSIAUR:PCIEMSIALR
in rcar_msi_setup_irqs(), incorrectly programmed PCIEMSIAUR cannot
cause memory corruption or other issues.
There is however the possibility that if virt_to_phys(__get_free_pages())
returned address above the 32bit boundary _and_ PCIEMSIAUR was programmed
to 0x0 _and_ if the system had physical RAM at the address matching the
value of PCIEMSIALR, a PCIe card driver could allocate a buffer with a
physical address matching the value of PCIEMSIALR and a remote write to
such a buffer by a PCIe card would trigger a spurious MSI.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0d14edd2ba43b995bef4dd5da5ffe0ae19321a1 ]
In case __get_free_pages() fails and returns NULL, fix the return
value to -ENOMEM and release resources to avoid dereferencing a
NULL pointer.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd8a44bd5b76dc77133f814dd63d414d49dc74c0 ]
Platforms which populate msi_host_init() have their own MSI controller
logic. Writing to MSI control registers on platforms which do not use
Designware's MSI controller logic might have side effects.
To be safe, do not write to MSI control registers if the platform uses
its own MSI controller logic instead of Designware's MSI one.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f316a2b53cd7f37963ae20ec7072eb27a349a4ce ]
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b22af42b3e57c3a49a4c4a54c7d8a1363af75e90 ]
SERDES connected to the PCIe controller in AM654 requires
power on reset enable (POR_EN) to be set in the SERDES. The
SERDES driver sets POR_EN in the reset ops and it has to be
invoked before init or enable ops. In order for SERDES driver
to set POR_EN, invoke the phy_reset() API in pci-keystone driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6b7330303a8186fb211357e6d379237fe9d2ece1 ]
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc69a3d567941784c3d00e1d0834582b42b0b3e7 ]
To avoid a memory leak, free the page allocated for MSI IRQ in
dw_pcie_free_msi().
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9e2b5de5604a6ff2626c51e77014d92c9299722c ]
If we ever did MSI-related initializations, we need to call
dw_pcie_free_msi() in the error code path.
Remove the IS_ENABLED(CONFIG_PCI_MSI) check for MSI init because
pci_msi_enabled() already has a stub for !CONFIG_PCI_MSI.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit be20bbcb0a8cb5597cc62b3e28d275919f3431df upstream.
Reestablish the PCIe link very early in the resume process in case it
went down to prevent PCI accesses from hanging the bus. Such accesses
can happen early in the PCI resume process, as early as the
SUSPEND_RESUME_NOIRQ step, thus the link must be reestablished in the
driver resume_noirq() callback.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar")
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
[lorenzo.pieralisi@arm.com: reformatted commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 340d455699400f2c2c0f9b3f703ade3085cdb501 upstream.
When we hot-remove a device, usually the host sends us a PCI_EJECT message,
and a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
When we execute the quick hot-add/hot-remove test, the host may not send
us the PCI_EJECT message if the guest has not fully finished the
initialization by sending the PCI_RESOURCES_ASSIGNED* message to the
host, so it's potentially unsafe to only depend on the
pci_destroy_slot() in hv_eject_device_work() because the code path
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
is not called in this case. Note: in this case, the host still sends the
guest a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
In the quick hot-add/hot-remove test, we can have such a race before
the code path
pci_devices_present_work()
-> new_pcichild_device()
adds the new device into the hbus->children list, we may have already
received the PCI_EJECT message, and since the tasklet handler
hv_pci_onchannelcallback()
may fail to find the "hpdev" by calling
get_pcichild_wslot(hbus, dev_message->wslot.slot)
hv_pci_eject_device() is not called; Later, by continuing execution
create_root_hv_pci_bus()
-> hv_pci_assign_slots()
creates the slot and the PCI_BUS_RELATIONS message with
bus_rel->device_count == 0 removes the device from hbus->children, and
we end up being unable to remove the slot in
hv_pci_remove()
-> hv_pci_remove_slots()
Remove the slot in pci_devices_present_work() when the device
is removed to address this race.
pci_devices_present_work() and hv_eject_device_work() run in the
singled-threaded hbus->wq, so there is not a double-remove issue for the
slot.
We cannot offload hv_pci_eject_device() from hv_pci_onchannelcallback()
to the workqueue, because we need the hv_pci_onchannelcallback()
synchronously call hv_pci_eject_device() to poll the channel
ringbuffer to work around the "hangs in hv_compose_msi_msg()" issue
fixed in commit de0aa7b2f97d ("PCI: hv: Fix 2 hang issues in
hv_compose_msi_msg()")
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: rewritten commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15becc2b56c6eda3d9bf5ae993bafd5661c1fad1 upstream.
When we unload the pci-hyperv host controller driver, the host does not
send us a PCI_EJECT message.
In this case we also need to make sure the sysfs PCI slot directory is
removed, otherwise a command on a slot file eg:
"cat /sys/bus/pci/slots/2/address"
will trigger a
"BUG: unable to handle kernel paging request"
and, if we unload/reload the driver several times we would end up with
stale slot entries in PCI slot directories in /sys/bus/pci/slots/
root@localhost:~# ls -rtl /sys/bus/pci/slots/
total 0
drwxr-xr-x 2 root root 0 Feb 7 10:49 2
drwxr-xr-x 2 root root 0 Feb 7 10:49 2-1
drwxr-xr-x 2 root root 0 Feb 7 10:51 2-2
Add the missing code to remove the PCI slot and fix the current
behaviour.
Fixes: a15f2c08c708 ("PCI: hv: support reporting serial number as slot information")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: reformatted the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05f151a73ec2b23ffbff706e5203e729a995cdc2 upstream.
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Use match_string() instead of reimplementing it (Andy Shevchenko)
- Enable SERR# forwarding for all bridges (Bharat Kumar Gogada)
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
- Fix DPC use of uninitialized data (Dongdong Liu)
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more
reliably (Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
- Reorder pciehp cached state/hardware state updates to avoid missed
interrupts (Mika Westerberg)
- Turn ibmphp semaphores into completions or mutexes (Arnd Bergmann)
- Mark expected switch fall-through (Mathieu Malaterre)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Add ACS and pciehp quirks for HXT SD4800 (Shunyong Yang)
- Consolidate Rohm Vendor ID definitions (Andy Shevchenko)
- Use u32 (not __u32) for things not exposed to userspace (Logan
Gunthorpe)
- Fix locking semantics of bus and slot reset interfaces (Alex
Williamson)
- Update PCIEPORTBUS Kconfig help text (Hou Zhiqiang)
- Allow portdrv to claim subtractive decode Ports so PCIe services will
work for them (Honghui Zhang)
- Report PCIe links that become degraded at run-time (Alexandru
Gagniuc)
- Blacklist Gigabyte X299 Root Port power management to fix Thunderbolt
hotplug (Mika Westerberg)
- Revert runtime PM suspend/resume callbacks that broke PME on network
cable plug (Mika Westerberg)
- Disable Data Link State Changed interrupts to prevent wakeup
immediately after suspend (Mika Westerberg)
- Extend altera to support Stratix 10 (Ley Foon Tan)
- Allow building altera driver on ARM64 (Ley Foon Tan)
- Replace Douglas with Tom Joseph as Cadence PCI host/endpoint
maintainer (Lorenzo Pieralisi)
- Add DT support for R-Car RZ/G2E (R8A774C0) (Fabrizio Castro)
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo
Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of
open-coded reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
- Fix mvebu prefetchable BAR regression caused by common bridge
emulation that assumed all bridges had prefetchable windows (Thomas
Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
- Configure MPS settings for VMD root ports (Jon Derrick)
* tag 'pci-v5.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (92 commits)
PCI: Update PCIEPORTBUS Kconfig help text
PCI: Fix "try" semantics of bus and slot reset
PCI/LINK: Report degraded links via link bandwidth notification
dt-bindings: PCI: altera: Add altr,pcie-root-port-2.0
PCI: altera: Enable driver on ARM64
PCI: altera: Add Stratix 10 PCIe support
PCI/PME: Fix possible use-after-free on remove
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
...
|
|
- Configure MPS settings for VMD root ports (Jon Derrick)
* remotes/lorenzo/pci/vmd:
PCI/VMD: Configure MPS settings before adding devices
|
|
- Fix mvebu prefetchable BAR regression caused by common bridge emulation
that assumed all bridges had prefetchable windows (Thomas Petazzoni)
- Make advk_pci_bridge_emul_ops static (Wei Yongjun)
* remotes/lorenzo/pci/misc:
PCI: aardvark: Make symbol 'advk_pci_bridge_emul_ops' static
PCI: pci-bridge-emul: Extend pci_bridge_emul_init() with flags
PCI: pci-bridge-emul: Create per-bridge copy of register behavior
|
|
- Fix mediatek MMIO size computation to enable full size of available
MMIO space (Honghui Zhang)
- Fix mediatek DMA window size computation to allow endpoint DMA access
to full DRAM address range (Honghui Zhang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Enlarge PCIe2AHB window size to support 4GB DRAM
PCI: mediatek: Fix memory mapped IO range size computation
|
|
- Remove duplicate struct hv_vp_set in favor of struct hv_vpset (Maya
Nakamura)
- Rework hv_irq_unmask() to use cpumask_to_vpset() instead of open-coded
reimplementation (Maya Nakamura)
- Align Hyper-V struct retarget_msi_interrupt arguments (Maya Nakamura)
* remotes/lorenzo/pci/hv:
PCI: hv: Refactor hv_irq_unmask() to use cpumask_to_vpset()
PCI: hv: Replace hv_vp_set with hv_vpset
PCI: hv: Add __aligned(8) to struct retarget_msi_interrupt
|
|
- Use memcpy_fromio()/memcpy_toio() instead of plain memcpy() in PCI
endpoint framework (Wen Yang)
- Add interface to discover supported endpoint features to replace a
bitfield that wasn't flexible enough (Kishon Vijay Abraham I)
- Implement the new supported-feature interface for designware-plat,
dra7xx, rockchip, cadence (Kishon Vijay Abraham I)
- Fix issues with 64-bit BAR in endpoints (Kishon Vijay Abraham I)
- Add layerscape endpoint mode support (Xiaowei Bao)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: Add the layerscape EP device support
PCI: layerscape: Add EP mode support
arm64: dts: Add the PCIE EP node in dts
dt-bindings: add DT binding for the layerscape PCIe controller with EP mode
PCI: endpoint: Remove features member in struct pci_epc
PCI: designware-plat: Remove setting epc->features in Designware plat EP driver
PCI: rockchip: Remove pci_epf_linkup() from Rockchip EP driver
PCI: cadence: Remove pci_epf_linkup() from Cadence EP driver
PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features
PCI: pci-epf-test: Do not allocate next BARs memory if current BAR is 64Bit
PCI: pci-epf-test: Remove setting epf_bar flags in function driver
PCI: endpoint: Fix pci_epf_alloc_space() to set correct MEM TYPE flags
PCI: endpoint: Add helper to get first unreserved BAR
PCI: cadence: Populate ->get_features() cdns_pcie_epc_ops
PCI: rockchip: Populate ->get_features() dw_pcie_ep_ops
PCI: pci-dra7xx: Populate ->get_features() dw_pcie_ep_ops
PCI: designware-plat: Populate ->get_features() dw_pcie_ep_ops
PCI: dwc: Add ->get_features() callback function to dw_pcie_ep_ops
PCI: endpoint: Add new pci_epc_ops to get EPC features
PCI: endpoint: functions: Use memcpy_fromio()/memcpy_toio()
|
|
- Add dra72x/dra74x/dra76x SoC compatible strings (Kishon Vijay
Abraham I)
- Enable x2 mode support for dra72x/dra74x/dra76x SoC (Kishon Vijay
Abraham I)
- Configure dra7xx PHY to PCIe mode (Kishon Vijay Abraham I)
- Simplify dwc (remove unnecessary header includes, name variables
consistently, reduce inverted logic, etc) (Gustavo Pimentel)
- Add i.MX8MQ support (Andrey Smirnov)
- Add message to help debug dwc MSI-X mask bit errors (Gustavo Pimentel)
- Work around imx7d PCIe PLL erratum (Trent Piepho)
- Don't assert qcom reset GPIO during probe (Bjorn Andersson)
- Skip dwc MSI init if MSIs have been disabled (Lucas Stach)
* remotes/lorenzo/pci/dwc:
PCI: dwc: skip MSI init if MSIs have been explicitly disabled
PCI: dwc: Remove superfluous shifting in definitions
PCI: dwc: Make use of GENMASK/FIELD_PREP
PCI: dwc: Make use of BIT() in constant definitions
PCI: dwc: Share code for dw_pcie_rd/wr_other_conf()
PCI: dwc: Make use of IS_ALIGNED()
PCI: imx6: Add code to request/control "pcie_aux" clock for i.MX8MQ
dt-bindings: imx6q-pcie: Add "pcie_aux" clock for imx8mq
PCI: qcom: Don't deassert reset GPIO during probe
PCI: imx: Add workaround for e10728, IMX7d PCIe PLL failure
ARM: dts: imx7d: Add node for PCIe PHY
dt-bindings: imx6q-pcie: Add description of imx7d pcie phy
PCI: dwc: Print debug error message when MSI-X entry control mask bit is set
PCI: imx6: Add support for i.MX8MQ
PCI: imx6: Convert DIRECT_SPEED_CHANGE quirk code to use a flag
PCI: imx6: Mark PHY functions as i.MX6 specific
PCI: imx6: Introduce drvdata
PCI: dwc: Replace bit rotation operation (1 << bit) with BIT(bit)
PCI: dwc: Improve code readability and simplify mask/unmask operations
PCI: dwc: Rename variable name from data to d on dw_pcie_irq_domain_free()
PCI: dwc: Rename variable name from data to d on dw_pci_msi_set_affinity()
PCI: dwc: Rename variable name from data to d on dw_pci_setup_msi_msg()
PCI: dwc: Rename variable name from data to d on dw_pci_bottom_mask/unmask()
PCI: dwc: Remove unnecessary header include (signal.h)
PCI: dwc: Remove unnecessary header include (of_gpio.h)
PCI: dwc: dra7xx: Invoke phy_set_mode() API to set PHY mode to PHY_MODE_PCIE
PCI: dwc: dra7xx: Enable x2 mode support for dra74x, dra76x and dra72x
dt-bindings: PCI: dra7xx: Add properties to enable x2 lane in dra7
dt-bindings: PCI: dra7xx: Add SoC specific compatible strings
|
|
Enable PCIE_ALTERA on ARM64 platform.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Add PCIe Root Port support for Stratix 10 device.
Main differences compared to the PCIe Root Port IP on Cyclone V
and Arria 10 devices:
- HIP interface to access Root Port configuration register
- TLP programming flow:
- One REG0 register
- Don't need to check alignment
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Fix the following sparse warning:
drivers/pci/controller/pci-aardvark.c:469:28: warning:
symbol 'advk_pci_bridge_emul_ops' was not declared. Should it be static?
Fixes: 8a3ebd8de328 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
|
|
Since 7c5925afbc58 (PCI: dwc: Move MSI IRQs allocation to IRQ domains
hierarchical API) the MSI init claims one of the controller IRQs as a
chained IRQ line for the MSI controller. On some designs, like the i.MX6,
this line is shared with a PCIe legacy IRQ. When the line is claimed for
the MSI domain, any device trying to use this legacy IRQs will fail to
request this IRQ line.
As MSI and legacy IRQs are already mutually exclusive on the DWC core,
as the core won't forward any legacy IRQs once any MSI has been enabled,
users wishing to use legacy IRQs already need to explictly disable MSI
support (usually via the pci=nomsi kernel commandline option). To avoid
any issues with MSI conflicting with legacy IRQs, just skip all of the
DWC MSI initalization, including the IRQ line claim, when MSI is disabled.
Fixes: 7c5925afbc58 ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API")
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: stable@vger.kernel.org
|
|
Remove the duplicate implementation of cpumask_to_vpset() and use the
shared implementation. Export hv_max_vp_index, which is required by
cpumask_to_vpset().
Signed-off-by: Maya Nakamura <m.maya.nakamura@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
|
|
Remove a duplicate definition of VP set (hv_vp_set) and use the common
definition (hv_vpset) that is used in other places.
Change the order of the members in struct hv_pcibus_device so that the
declaration of retarget_msi_interrupt_params is the last member. Struct
hv_vpset, which contains a flexible array, is nested two levels deep in
struct hv_pcibus_device via retarget_msi_interrupt_params.
Add a comment that retarget_msi_interrupt_params should be the last
member of struct hv_pcibus_device.
Signed-off-by: Maya Nakamura <m.maya.nakamura@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
|
|
Because Hyper-V requires that hypercall arguments be aligned on an 8
byte boundary, add __aligned(8) to struct retarget_msi_interrupt.
Link: https://lore.kernel.org/lkml/87k1hlqlby.fsf@vitty.brq.redhat.com/
Signed-off-by: Maya Nakamura <m.maya.nakamura@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
The PCIE_AXI_WINDOW0 register defines the inbound window size for
requests coming from PCI endpoints. Requests outside of this window will
be treated as unsupported requests.
Enlarge this window size from 2^31 to 2^33 to support a 8GB address
space (which gives endpoints DMA access to full 4GB DRAM address range
- physical DRAM starts at 0x40000000).
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Mediatek's HW assigns a MMIO address range (typically starts from
0x20000000 to 0x2fffffff for both mt2712 and mt7622) for PCI usage.
This MMIO address space represents the address space that can
be allocated to PCI devices through Base Address Registers.
Even though the full MMIO address range is available to be allocated, it
should be enabled by the PCIE_AHB_TRANS_BASE register in the host
controller and the size that is enabled is determined by AHB2PCIE_SIZE
bits in this register.
Owing to a bug in the MMIO window size computation, current code does
not enable the full size of the available MMIO address range in the
PCI host controller; if the PCI devices BARs requested size exceeds the
size enabled through the PCIE_AHB_TRANS_BASE register the requests
targeting the disabled address address space will be blocked by the root
complex causing a system error.
Existing code has never run into a system error in production because
even half of the enabled MMIO range (128MB) is big enough for typical
devices BAR requests (4MB) but the full MMIO address range should
be enabled regardless.
Fix the MMIO window size computation by using resource_size(mem) instead
of mem->end - mem->start.
Since the MMIO window size for both MT2712 and MT7622 is 0x10000000,
this change will update the parameter passed to fls() from 0xfffffff to
0x10000000 and calculate the whole memory mapped IO range size
correctly.
Detected through coccinelle semantic patch (and related warning):
scripts/coccinelle/api/resource_size.cocci:
pcie-mediatek.c:720:13-16: WARNING: Suspicious code. resource_size is maybe missing with mem
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[lorenzo.pieralisi@arm.com: rewrote the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Surrounding definitions no longer use explicit shift, so "<< 0" here
serve no purpose. Remove them. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
|
|
Convert various multi-bit fields to be defined using GENMASK/FIELD_PREP.
This way bit field boundaries are defined in a single place only, as
well as defined in a way that makes it easier to verify them against the
reference manual. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
|
|
Avoid using explicit left shifts and convert various definitions to
use BIT() instead. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
[lorenzo.pieralisi@arm.com: fixed PORT_LOGIC_SPEED_CHANGE redefinition]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
|
|
Default implementation of pcie_rd_other_conf() and
dw_pcie_wd_other_conf() share more than 80% of their code. Move shared
code into a dedicated subroutine and convert pcie_rd_other_conf() and
dw_pcie_wd_other_conf() to use it. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
|
|
Make the intent a bit more clear as well as get rid of explicit
arithmetic by using IS_ALIGNED() to determine if "addr" is aligned to
"size". No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
|
|
The PCIe IP block has an additional clock, "pcie_aux", that needs to
be controlled by the driver. Add code to support it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
|
|
Acquiring the reset GPIO low means that reset is being deasserted, this
is followed almost immediately with qcom_pcie_host_init() asserting it,
initializing it and then finally deasserting it again, for the link to
come up.
Some PCIe devices requires a minimum time between the initial deassert
and subsequent reset cycles. In a platform that boots with the reset
GPIO asserted this requirement is being violated by this deassert/assert
pulse.
Acquire the reset GPIO high to prevent this situation by matching the
state to the subsequent asserted state.
Fixes: 82a823833f4e ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org
|
|
Depending on the capabilities of the PCI controller/platform, the
PCI-to-PCI bridge emulation behavior might need to be different. For
example, on platforms that use the pci-mvebu code, we currently don't
support prefetchable memory BARs, so the corresponding fields in the
PCI-to-PCI bridge configuration space should be read-only.
To implement this, extend pci_bridge_emul_init() to take a "flags"
argument, with currently one flag supported:
PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR
that will make the prefetchable memory base and limit registers
read-only.
The pci-mvebu and pci-aardvark drivers are updated accordingly.
Fixes: 1f08673eef123 ("PCI: mvebu: Convert to PCI emulated bridge config space")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
Cc: Luís Mendes <luis.p.mendes@gmail.com>
Cc: Leigh Brown <leigh@solinno.co.uk>
|
|
Add the PCIe EP mode support to the layerscape platform controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <minghuan.lian@nxp.com>
Reviewed-by: Zhiqiang Hou <zhiqiang.hou@nxp.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Now that pci-epf-test uses get_features callback and
dw_plat_pcie_epc_features in Designware plat EP driver already indicates
it doesn't support linkup notification and is MSIX capable, remove setting
epc->features which is not used anymore by the endpoint function driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
pci_epf_linkup() is intended to be invoked if the EPC supports linkup
notification. Now that pci-epf-test uses get_features callback, which
indicates Rockchip EP driver doesn't support linkup notification, remove
pci_epf_linkup() from Rockchip EP driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
pci_epf_linkup() is intended to be invoked if the EPC supports linkup
notification. Now that pci-epf-test uses the get_features() callback,
which indicates Cadence EP driver doesn't support the linkup notification,
remove pci_epf_linkup() from Cadence EP driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by Cadence PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by Rockchip PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by DRA7xx PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Populate ->get_features() dw_pcie_ep_ops to return the EPC features
supported by Designware PCIe endpoint controller.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Each platform using Designware PCIe core can support different set of
endpoint features. Add a new callback function ->get_features() in
dw_pcie_ep_ops so that each platform using Designware PCIe core can
advertise its supported features to the endpoint function driver.
Tested-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This implements the workound described in the NXP IMX7d erratum e10728.
Initial VCO oscillation may fail under corner conditions such as cold
temperature. It causes PCIe PLL to fail to lock in the initialization
phase, which results in the PCIe link failing to come up.
The workaround is to disable Duty-Cycle Corrector (DCC) calibration
after G_RST.
To do this it is necessary to gain access to the undocumented and
currently unused PCIe PHY register bank. A new device tree node of type
"fsl,imx7d-pcie-phy" is created for the PHY block and the existing PCIe
device uses a phandle named "fsl,imx7d-pcie-phy" to point to it.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
[lorenzo.pieralisi@arm.com: updated log string, commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
|
|
Add debug error message when MSI-X entry control mask bit is set, to help
debug the reason why a MSI-X interrupt is not being triggered.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Joao Pinto <joao.pinto@synopsys.com>
|
|
Add code needed to support i.MX8MQ variant.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
|
|
Both i.MX7D and i.MX8MQ have the same behaviour when it comes to
clearing DIRECT_SPEED_CHANGE bit when no speed change occurs, so to
handle variants correctly add a flag instead of checking the IP block
variant.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
|
