summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)AuthorFilesLines
2008-12-17Merge branch 'mxc-pu-imxfb' of ↵Russell King2-58/+95
git://pasiphae.extern.pengutronix.de/git/imx/linux-2.6 into devel
2008-12-16Merge branch 'omap3-upstream' of ↵Russell King29-59/+221
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
2008-12-13Merge git://git.marvell.com/orion into develRussell King9-21/+67
2008-12-12e1000e: fix double release of mutexJeff Kirsher1-2/+7
During a reset, releasing the swflag after it failed to be acquired would cause a double unlock of the mutex. Instead, test whether acquisition of the swflag was successful and if not, do not release the swflag. The reset must still be done to bring the device to a quiescent state. This resolves [BUG 12200] BUG: bad unlock balance detected! e1000e http://bugzilla.kernel.org/show_bug.cgi?id=12200 Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10sungem: improve ethtool output with internal pcs and serdesHermann Lauer1-0/+15
From: Hermann Lauer <Hermann.Lauer@iwr.uni-heidelberg.de> Attached is a patch which improves the output of ethtool (see below) to some sensefull values with a sungem fibre card which uses the sungem interal pcs connected to a serdes chip. The seriallink case in the driver is untouched. Most values are hardcoded, because gigabit fibre autoneg is anyways limited and the driver don't really support much at the moment with that hardware. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-09sungem: Make PCS PHY support partially work again.David S. Miller1-56/+73
As reported by Hermann Lauer, PCS PHY support in the sungem driver simply doesn't work. When the chip is reset due to open, or some other similar operation, the PCS is reset too but we don't program it back into a running state. The result is no link when the device is brought up. This partially rectifies the situation for the moment, by kicking the PCS after a sungem chip reset so that it will renegotiate and be re-enabled again. The behavior is still a little bit dodgy as the added renegotiate make the link take some time after bringing the interface up, but this is a significant improvement in that things actually work now :-) Based almost entirely upon an initial patch by Hermann. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-05zd1211rw: use unaligned safe memcmp() in-place of compare_ether_addr()Shaddy Baddah1-1/+1
Under my 2.6.28-rc6 sparc64, when associating to an AP through my zd1211rw device, I was seeing kernel log messages like (not exact output): Kernel unaligned access at TPC[10129b68] zd_mac_rx+0x144/0x32c [zd1211rw] For the zd1211rw module, on RX, the 80211 packet will be located after the PLCP header in the skb data buffer. The PLCP header being 5 bytes long, the 80211 header will start unaligned from an aligned skb buffer. As per Documentation/unaligned-memory-access.txt, we must replace the not unaligned() safe compare_ether_addr() with memcmp() to protect architectures that require alignment. Signed-off-by: Shaddy Baddah <shaddy_baddah@hotmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05ipw2200: fix netif_*_queue() removal regressionZhu Yi1-0/+4
In "ipw2200: Call netif_*_queue() interfaces properly", netif_stop_queue() and netif_wake_queue() were removed with the reason "netif_carrier_{on,off}() handles starting and stopping packet flow into the driver". The patch also removes a valid condition check that ipw_tx_skb() cannot be called if device is not in STATUS_ASSOCIATED state. But netif_carrier_off() doesn't guarantee netdev->hard_start_xmit won't be called because linkwatch event is handled in a delayed workqueue. This caused a kernel oops reported by Frank Seidel: https://bugzilla.novell.com/show_bug.cgi?id=397390 This patch fixes the problem by moving the STATUS_ASSOCIATED check back to ipw_tx_skb(). It also adds a missing netif_carrier_off() call to ipw_disassociate(). Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: Chatre, Reinette <reinette.chatre@intel.com> Tested-by: Frank Seidel <fseidel@suse.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-05iwlwifi: clean key table in iwl_clear_stations_table functionTomas Winkler2-3/+24
This patch cleans uCode key table bit map iwl_clear_stations_table since all stations are cleared also the key table must be. Since the keys are not removed properly on suspend by mac80211 this may result in exhausting key table on resume leading to memory corruption during removal This patch also fixes a memory corruption problem reported in http://marc.info/?l=linux-wireless&m=122641417231586&w=2 and tracked in http://bugzilla.kernel.org/show_bug.cgi?id=12040. When the key is removed a second time the offset is set to 255 - this index is not valid for the ucode_key_table and corrupts the eeprom pointer (which is 255 bits from ucode_key_table). Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Reported-by: Carlos R. Mafra <crmafra2@gmail.com> Reported-by: Lukas Hejtmanek <xhejtman@ics.muni.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-12-04netx-eth: initialize per device spinlockUwe Kleine-König1-0/+2
The spinlock used in the netx-eth driver was never properly initialized. This was noticed using CONFIG_DEBUG_SPINLOCK=y Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-04enc28j60: Fix sporadic packet loss (corrected again)Baruch Siach1-2/+14
Packet data read from the RX buffer the when the RSV is at the end of the RX buffer does not warp around. This causes packet loss, as the actual data is never read. Fix this by calculating the right packet data location. Thanks to Shachar Shemesh for suggesting the fix. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03bnx2: Add workaround to handle missed MSI.Michael Chan2-3/+38
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI address/data are stored only when the MSI enable bit is toggled. As a result, SMP affinity no longer works in the latest kernel. A more serious problem is that the driver will no longer receive interrupts when the MSI receiving CPU goes offline. The workaround in this patch only addresses the problem of CPU going offline. When that happens, the driver's timer function will detect that it is making no forward progress on pending interrupt events and will recover from it. Eric Dumazet reported the problem. We also found that if an interrupt is internally asserted while MSI and INTA are disabled, the chip will end up in the same state after MSI is re-enabled. The same workaround is needed for this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Tested-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds21-50/+138
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits) MAINTAINERS: add netdev to ATM ATM: horizon, fix hrz_probe fail path pppol2tp: Add missing sock_put() in pppol2tp_release() net: Fix soft lockups/OOM issues w/ unix garbage collector macvlan: don't broadcast PAUSE frames to macvlan devices Phonet: fix oops in phonet_address_del() on non-Phonet device netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock sungem: Fix PCS_MIICTRL register write in gem_init_phy(). net: make skb_truesize_bug() call WARN() net: hp-plus uses eip_poll net/wireless/reg.c: fix bad WARN_ON in if statement ath5k: disable beacon filter when station is not associated ath5k: fix Security issue in DebugFS part of ath5k ath9k: correct expected max RX buffer size ath9k: Fix SW-IOMMU bounce buffer starvation mac80211 : Fix setting ad-hoc mode and non-ibss channel iwlagn: fix DMA sync phylib: Add Vitesse VSC8221 SGMII PHY rose: zero length frame filtering in af_rose.c bridge: netfilter: fix update_pmtu crash with GRE ...
2008-12-03Merge branch 'for-rmk' of ↵Russell King2-0/+46
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel Conflicts: arch/arm/mach-pxa/pxa25x.c
2008-12-02[ARM] pxa: move UART register definitions into dedicated regs-uart.hEric Miao1-0/+1
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02[ARM] pxa: move FICP register definitions into pxaficp_ir.cEric Miao1-0/+42
Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02[ARM] pxa: explicit #include <mach/dma.h> in various driversEric Miao1-0/+3
Where 'pxa_dma_desc' and 'pxa_{request,free}_dma' are referenced. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-12-02[ARM] fix missing includes for iop33x and sa1100_irRussell King1-1/+1
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-12-01Merge branch 'for-linus' of ↵Linus Torvalds3-1/+47
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/mlx4: Fix MTT leakage in resize CQ IB/ehca: Fix problem with generated flush work completions IB/ehca: Change misleading error message on memory hotplug mlx4_core: Save/restore default port IB capability mask
2008-12-01Merge branch 'merge' of ↵Linus Torvalds1-1/+2
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc: Fix system calls on Cell entered with XER.SO=1 powerpc/cell: Fix GDB watchpoints, again powerpc/mpic: Don't reset affinity for secondary MPIC on boot powerpc/cell/axon-msi: Retry on missing interrupt powerpc: Fix boot freeze on machine with empty memory node powerpc: Fix IRQ assignment for some PCIe devices powerpc/spufs: Fix spinning in spufs_ps_fault on signal powerpc/mpc832x_rdb: fix swapped ethernet ids powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610 powerpc/85xx: L2 cache size wrong in 8572DS dts powerpc/virtex: Update defconfigs powerpc/52xx: update defconfigs xsysace: Fix driver to use resource_size_t instead of unsigned long powerpc/virtex: fix various format/casting printk mismatches powerpc/mpc5200: fix bestcomm Kconfig dependencies powerpc/44x: Fix 460EX/460GT machine check handling powerpc/40x: Limit allocable DRAM during early mapping
2008-11-30get xenbus_driver ->probe() "recognized" by modpostAl Viro1-3/+3
... by giving the instances' names magic suffix recognized by modpost ;-/ Their ->probe() is __devinit Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-30section errors in smc911x/smc91xAl Viro2-10/+10
a) ->probe() can be __devinit; no need to put it into .text b) calling __init stuff from it, OTOH, is wrong c) ->remove() is __devexit fodder Acked-by: rmk+kernel@arm.linux.org.uk Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-30section misannotation in ibmtr_csAl Viro1-1/+1
ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether that's the right thing to do there is a separate question, but since it's PCMCIA and thus will never compile without HOTPLUG... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-30ixgbe section fixesAl Viro1-5/+4
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem. Several helpers called by it also are misannotated __devinit. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-29[ARM] Hide ISA DMA API when ISA_DMA_API is unsetRussell King2-2/+2
When ISA_DMA_API is unset, we're not implementing the ISA DMA API, so there's no point in publishing the prototypes via asm/dma.h, nor including the machine dependent parts of that API. This allows us to remove a lot of mach/dma.h files which don't contain any useful code. Unfortunately though, some platforms put their own private non-ISA definitions into mach/dma.h, so we leave these behind and fix the appropriate #include statments. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-11-29pppol2tp: Add missing sock_put() in pppol2tp_release()Frédéric Moulins1-0/+1
pppol2tp_sock_to_session() do sock_hold() if the session to release is not NULL. Signed-off-by: Frédéric Moulins <frederic.moulins@alsatis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-29mlx4_core: Save/restore default port IB capability maskJack Morgenstein3-1/+47
Commit 7ff93f8b ("mlx4_core: Multiple port type support") introduced support for different port types. As part of that support, SET_PORT is invoked to set the port type during driver startup. However, as a side-effect, for IB ports the invocation of this command also sets the port's capability mask to zero (losing the default value set by FW). To fix this, get the default ib port capabilities (via a MAD_IFC Port Info query) during driver startup, and save them for use in the mlx4_SET_PORT command when setting the port-type to Infiniband. This patch fixes problems with subnet manager (SM) failover such as <https://bugs.openfabrics.org/show_bug.cgi?id=1183>, which occurred because the IsTrapSupported bit in the capability mask was zeroed. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-11-28[ARM] pxa: avoid polluting the kernel's namespaceRussell King2-0/+2
Avoid unnecessarily pollution of the kernel's namespace by avoiding mach/hardware.h. Include this header file where necessary. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-11-27[ARM] clps7500: remove supportRussell King1-5/+1
The CLPS7500 platform has not built since 2.6.22-git7 and there seems to be no interest in fixing it. So, remove the platform support. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-11-27macvlan: don't broadcast PAUSE frames to macvlan devicesPatrick McHardy1-0/+3
PAUSE frames are only relevant for the real device, broadcasting them to all macvlan devices can cause a significant load increase. Reported-by: Ben Greear <greearb@candelatech.com> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26sungem: Fix PCS_MIICTRL register write in gem_init_phy().David S. Miller1-1/+1
Use writel not writeb. Noticed by Hermann Lauer. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26net: hp-plus uses eip_pollRandy Dunlap1-1/+1
hp-plus uses 8390p.c, so it should use eip_poll(), not ei_poll(). drivers/built-in.o: In function `hpp_probe1': hp-plus.c:(.init.text+0x9cbd): undefined reference to `ei_poll' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-26Merge branch 'master' of ↵David S. Miller6-19/+64
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2008-11-26ath5k: disable beacon filter when station is not associatedMartin Xu2-1/+35
Ath5k driver has too many interrupts per second at idle http://bugzilla.kernel.org/show_bug.cgi?id=11749 Signed-off-by: Martin Xu <martin.xu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26ath5k: fix Security issue in DebugFS part of ath5kCheng Renquan1-5/+5
http://bugzilla.kernel.org/show_bug.cgi?id=12076 Remove any write access to groups and others, only keep write permission to its owner, usually only root user. Reported-by: Jérôme Poulin <jeromepoulin@gmail.com> Signed-off-by: Cheng Renquan <crquan@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26ath9k: correct expected max RX buffer sizeLuis R. Rodriguez1-2/+11
We should only tell the hardware its capable of DMA'ing to us only what we asked dev_alloc_skb(). Prior to this it is possible a large RX'd frame could have corrupted DMA data but for us but we were saved only because we were previously also pci_map_single()'ing the same large value. The issue prior to this though was we were unmapping a smaller amount which the prior DMA patch fixed. Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26ath9k: Fix SW-IOMMU bounce buffer starvationLuis R. Rodriguez2-8/+8
This should fix the SW-IOMMU bounce buffer starvation seen ok kernel.org bugzilla 11811: http://bugzilla.kernel.org/show_bug.cgi?id=11811 Users on MacBook Pro 3.1/MacBook v2 would see something like: DMA: Out of SW-IOMMU space for 4224 bytes at device 0000:0b:00.0 Unfortunately its only easy to trigger on MacBook Pro 3.1/MacBook v2 so far so its difficult to debug (even with swiotlb=force). We were pci_unmap_single()'ing less bytes than what we called for with pci_map_single() and as such we were starving the swiotlb from its 64MB amount of bounce buffers. We remain consistent and now always use sc->rxbufsize for RX. While at it we update the beacon DMA maps as well to only use the data portion of the skb, previous to this we were pci_map_single()'ing more data for beaconing than what we tell the hardware it can use, therefore pushing more iotlb abuse. Still not sure why this is so easily triggerable on MacBook Pro 3.1, it may be the hardware configuration tends to use more memory > 3GB mark for DMA. Signed-off-by: Maciej Zenczykowski <zenczykowski@gmail.com> Signed-off-by: Bennyam Malavazi <Bennyam.Malavazi@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-26iwlagn: fix DMA syncJohannes Berg1-3/+5
For the RX DMA fix for iwlwifi ("iwlagn: fix RX skb alignment") Luis pointed out: > aligned_dma_addr can obviously be > real_dma_addr at this point, what > guarantees we can use it on our own whim? I asked around, and he's right, there may be platforms that do not allow passing such such an address to the DMA API functions. This patch changes it by using the proper dma_sync_single_range_for_cpu API invented for this purpose. Cc: Luis R. Rodriguez <mcgrof@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-11-25phylib: Add Vitesse VSC8221 SGMII PHYTrent Piepho1-9/+55
PHY is mostly compatible with the existing VSC8244 PHY. The init sequence is different and the interrupt mask lacks some bits present in the VSC8244. Rather than making a copy of the existing VSC234x config_intr function and change one constant, I modify it to select the interrupt mask based on which driver is calling it. This lets it be used by both drivers. Signed-off-by: Trent Piepho <tpiepho@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-24Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6-mpc52xx into mergePaul Mackerras1-1/+2
2008-11-24drivers/net/chelsio/sge.c: remove redundant argument commentsQinghuang Feng1-4/+0
remove redundant argument comments Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-24driver/net/*: remove redundant argument commentsQinghuang Feng6-12/+0
remove redundant argument comments in files of drivers/net/* Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-22net/hp-plus: fix link errorsRandy Dunlap1-1/+1
Fix hp-plus driver link errors. Builds as loadable module and kernel image driver. All drivers that use 8390.o or 8390p.o that will build on i386 with MCA/PCI/EISA/ISA were built successfully both =m and =y. drivers/built-in.o: In function `hpp_open': hp-plus.c:(.text+0xac06c): undefined reference to `eip_interrupt' hp-plus.c:(.text+0xac0d7): undefined reference to `eip_open' drivers/built-in.o: In function `hpp_close': hp-plus.c:(.text+0xac1bb): undefined reference to `eip_close' drivers/built-in.o: In function `hpp_probe1': hp-plus.c:(.init.text+0xa98a): undefined reference to `NS8390p_init' drivers/built-in.o: In function `hp_plus_probe': (.init.text+0xa9fe): undefined reference to `__alloc_eip_netdev' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-22axnet_cs / pcnet_cs: moving PCMCIA_DEVICE_PROD_ID for Netgear FA411Cord Walter2-1/+1
Hi, after noticing that my Netgear FA411 (PCMCIA-NIC) [1] stopped working with the release of the 2.6.25 kernel (sidux-version), I checked the respective driver sources and noticed that the pcnet_cs driver bailed out with "use axnet_cs instead" for the Netgear FA411, but axnet_cs doesn't claim this ID. I compiled a kernel with the PCMCIA-ID for the netgear card moved to axnet_cs from pcnet_cs which worked. I then contacted sidux-kernel maintainer Stefan Lippers-Hollmann who turned the info into this patch and integrated it into the kernel: <http://svn.berlios.de/svnroot/repos/fullstory/linux-sidux-2.6/trunk/debian/patches/features/2.6.27.4_PCMCIA_move-PCMCIA-ID-for-Netgear-FA411-from-pcnet_cs-to-axnet_cs.patch> This works for me and AFAIK there were no reports of any breakage for other devices on sidux-support. This looks like a trivial patch, but since I have very limited experience with kernel modifications I might be woefully wrong there. But if there are no side effects of this patch, is it possible to get it into the official kernel? I can provide more detailed information on the affected hardware if necessary. -cord [1] Socket 1 Device 0: [axnet_cs] (bus ID: 1.0) Configuration: state: on Product Name: NETGEAR FA411 Fast Ethernet Identification: manf_id: 0x0149 card_id: 0x0411 function: 6 (network) prod_id(1): "NETGEAR" (0x9aa79dc3) prod_id(2): "FA411" (0x40fad875) prod_id(3): "Fast Ethernet" (0xb4be14e3) prod_id(4): --- (---) From: Stefan Lippers-Hollmann <s.l-h@gmx.de> Date: Sat, 1 Nov 2008 23:53:04 +0000 Subject: PCMCIA: move PCMCIA ID for Netgear FA411 from pcnet_cs to axnet_cs: Since kernel 2.6.25, commit 61da96be07ec860e260ca4af0199b9d48d000b80 (pcnet_cs: if AX88190-based card, printk "use axnet_cs instead" message.), pcnet_cs bails out with "use axnet_cs instead" for the Netgear FA411, but axnet_cs doesn't claim this ID. Socket 1 Device 0: [axnet_cs] (bus ID: 1.0) Configuration: state: on Product Name: NETGEAR FA411 Fast Ethernet Identification: manf_id: 0x0149 card_id: 0x0411 function: 6 (network) prod_id(1): "NETGEAR" (0x9aa79dc3) prod_id(2): "FA411" (0x40fad875) prod_id(3): "Fast Ethernet" (0xb4be14e3) prod_id(4): --- (---) Cc: stable <stable@kernel.org> [2.6.25, 2.6.26, 2.6.27] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Cord Walter <qord@cwalter.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-21phy: fix phy_id detection also for broken hardware.Giuseppe Cavallaro1-2/+11
This patch fixes the case when the phy_ids is mostly Fs and in some case 0x0 due to broken hardware. Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20atl2: don't request irq on resume if netif runningAlan Jenkins1-3/+5
If the device is suspended with the cable disconnected, then resumed with the cable connected, dev->open is called before resume. During resume, we request an IRQ, but the IRQ was already assigned during dev->open, resulting in the warning shown below. Don't request an IRQ if the device is running. Call Trace: [<c011b89a>] warn_on_slowpath+0x40/0x59 [<c023df15>] raw_pci_read+0x4d/0x55 [<c023dff3>] pci_read+0x1c/0x21 [<c01bcd81>] __pci_find_next_cap_ttl+0x44/0x70 [<c01bce86>] __pci_find_next_cap+0x1a/0x1f [<c01bcef9>] pci_find_capability+0x28/0x2c [<c01c4144>] pci_msi_check_device+0x53/0x62 [<c01c49c2>] pci_enable_msi+0x3a/0x1cd [<e019f17b>] atl2_write_phy_reg+0x40/0x5f [atl2] [<c01061b1>] dma_generic_alloc_coherent+0x0/0xd7 [<e019f107>] atl2_request_irq+0x15/0x49 [atl2] [<e01a1481>] atl2_open+0x20b/0x297 [atl2] [<c024a35c>] dev_open+0x62/0x91 [<c0248b9a>] dev_change_flags+0x93/0x141 [<c024f308>] do_setlink+0x238/0x2d5 [<c02501b2>] rtnl_setlink+0xa9/0xbf [<c0297f0c>] mutex_lock+0xb/0x19 [<c024ffa7>] rtnl_dump_ifinfo+0x0/0x69 [<c0250109>] rtnl_setlink+0x0/0xbf [<c024fe42>] rtnetlink_rcv_msg+0x185/0x19f [<c0240fd1>] sock_rmalloc+0x23/0x57 [<c024fcbd>] rtnetlink_rcv_msg+0x0/0x19f [<c0259457>] netlink_rcv_skb+0x2d/0x71 [<c024fcb7>] rtnetlink_rcv+0x14/0x1a [<c025929e>] netlink_unicast+0x184/0x1e4 [<c025992a>] netlink_sendmsg+0x233/0x240 [<c023f405>] sock_sendmsg+0xb7/0xd0 [<c0129131>] autoremove_wake_function+0x0/0x2b [<c0129131>] autoremove_wake_function+0x0/0x2b [<c0147796>] mempool_alloc+0x2d/0x9e [<c020c923>] scsi_pool_alloc_command+0x35/0x4f [<c0297f0c>] mutex_lock+0xb/0x19 [<c028e867>] unix_stream_recvmsg+0x357/0x3e2 [<c01b81c9>] copy_from_user+0x23/0x4f [<c02452ea>] verify_iovec+0x3e/0x6c [<c023f5ab>] sys_sendmsg+0x18d/0x1f0 [<c023ffa8>] sys_recvmsg+0x146/0x1c8 [<c0240016>] sys_recvmsg+0x1b4/0x1c8 [<c0118f48>] __wake_up+0xf/0x15 [<c02586cd>] netlink_table_ungrab+0x17/0x19 [<c01b83ba>] copy_to_user+0x25/0x3b [<c023fe4a>] move_addr_to_user+0x50/0x68 [<c0240266>] sys_getsockname+0x6f/0x9a [<c0240280>] sys_getsockname+0x89/0x9a [<c015046a>] do_wp_page+0x3ae/0x41a [<c0151525>] handle_mm_fault+0x4c5/0x540 [<c02405d0>] sys_socketcall+0x176/0x1b0 [<c010376d>] sysenter_do_call+0x12/0x21 Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20Merge branch 'master' of ↵David S. Miller5-16/+23
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2008-11-20smc911x: Fix printf format typo in smc911x driver.Vernon Sauder1-1/+1
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20asix: Fix asix-based cards connecting to 10/100Mbs LAN.Pantelis Koukousoulas1-1/+3
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card. Without this patch, the card is recognized and the interface is brought up fine, but no packets actually flow through the interface. Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com> Acked-by: David Hollis <dhollis@davehollis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-20mv643xx_eth: fix recycle check boundLennert Buytenhek1-1/+2
When mv643xx_eth allocates skbuffs, it adds 'dma_get_cache_alignment() - 1' to the length it needs, so that it can align the skb's ->data pointer to a cache boundary. When checking whether a transmitted skbuff can be reused as a receive buffer, these bytes needs to be included into the minimum bound for the recycle check. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-15 18:48:27 +0300