| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
PTP and MMC modules base address can depend on the GMAC version. As this
is HW specific lets move this base address calculation to hwif.c. Also,
add an entry in the HW table so that we can specify the module offset.
This can later be extended to more modules, if deemed necessary.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the introducion of callbacks check in hwif.h we only call the
callback if HW supports it so there is no longer need to check for GMAC
version.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of relying on the GMAC version for choosing if we need to use
dma_{rx/tx}_mode or just dma_mode callback lets uniformize this and
always use the dma_{rx/tx}_mode callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop using if conditions depending on the GMAC version for clearing the
descriptor and use instead a helper implemented in the descriptor files.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop using if conditions depending on the GMAC version for setting the
the descriptor skbuff address and use instead a helper implemented in
the descriptor files.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is cutting down performance. Once the timer is armed it should run
after the time expires for the first packet sent and not the last one.
After this change, running iperf, the performance gain is +/- 24%.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables OSP (Operate on Second Packet) for GMAC4. The feature
allows DMA to fetch second descriptor while its still processing the
first one.
Running iperf, the performance gain is +/- 38%.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the representor only report the SW (slow-path) traffic
counters.
Add packet/bytes reporting of the HW counters, which account for the
total amount of traffic that was handled by the vport, both slow and
fast (offloaded) paths. The newly exposed counters are named
vport_rx/tx_packets/bytes.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For VF->VF and uplink->VF rules, the TC core (cls_api) attempts
to offload the same flow multiple times into the driver, b/c we
registered to the egdev callback.
Use the flow cookie to ignore attempts to add such flows, we can't
reject them (return error), b/c this will fail the offload attempt,
so we ignore that. We indentify wrong stat/del calls using the flow
ingress/egress flags, here we do return error to the core.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, each representor netdev use their own hash table to keep
the mapping from TC flow (f->cookie) to the driver offloaded instance.
The table is the one which originally was added for offloading TC NIC
(not eswitch) rules.
This scheme breaks when the core TC code calls us to add the same flow
twice, (e.g under egdev use case) since we don't spot that and offload
a 2nd flow into the HW with the wrong source vport.
As a pre-step to solve that, we move to use a single table which keeps
all offloaded TC eswitch flows. The table is located at the eswitch
uplink representor object.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This is a refactoring step to be able and store the hash table which
keeps track of offloaded TC flows in a different location for NIC
vs e-switch rules.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When an e-switch TC rule is offloaded through the egdev (egress
device) mechanism, we treat this as egress, all other cases (NIC
and e-switch) are considred ingress.
This is preparation step that will allow us to identify "wrong"
stat/del offload calls made by the TC core on egdev based flows and
ignore them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the merged eswitch capability is supported, allow offloading rules
between VFs which belong to different PFs (and hence have different
eswitch affinity).
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patches to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set a specific source e-switch when setting a rule that matches on the
ingress port.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Set a specific destination e-switch when setting a destination vport.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When creating FTE, properly distinguish between destination being vport
or tir. The previous code just worked accidentally b/c of both dest being
in the same offset within a union.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the TI drivers build just fine with COMPILE_TEST, cpmac (AR7) is
the exception because it uses a header file from
arch/mips/include/asm/mach-ar7/ar7.h and keystone netcp which requires
help from drivers/soc/ti/ for queue management helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.
This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.
Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32
HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42
HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92
HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41
HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-05-17
This series contains updates to ixgbe, ixgbevf and ice drivers.
Cathy Zhou resolves sparse warnings by using the force attribute.
Mauro S M Rodrigues fixes a bug where IRQs were not freed if a PCI error
recovery system opts to remove the device which causes
ixgbe_io_error_detected() to return PCI_ERS_RESULT_DISCONNECT before
calling ixgbe_close_suspend() which results in IRQs not freed and
crashing when the remove handler calls pci_disable_device(). Resolved
this by calling ixgbe_close_suspend() before evaluating the PCI channel
state.
Pavel Tatashin releases the rtnl_lock during the call to
ixgbe_close_suspend() to allow scaling if device_shutdown() is
multi-threaded.
Emil modifies ixgbe to not validate the MAC address during a reset,
unless the MAC was set on the host so that the VF will get a new MAC
address every time it reloads. Also updates ixgbevf to set
hw->mac.perm_addr in order to retain the custom MAC on a reset.
Anirudh updates the ice NVM read/erase/update AQ commands to align with
the latest specification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't store repr pointer to reprs array until the representor is
successfully created. This avoids message about "representor
destruction" even when it was never created. Also it cleans-up the flow.
Also, check return value after port alloc.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent flood of RX error prints during heavy traffic with weak signal
in link by checking net_ratelimit() before using netdev_err().
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: small rework, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove special stop/start handling from the set_mac_address callback.
All this special care is not needed, and can be removed. It also
simplifies the up/down status in the driver and helps avoiding possible
link status mismatch issues.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid repeating the check for free aggregated descriptors when it
already failed at the beginning of the function.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.
The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.
The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.
I also merged wireless-drivers due to an iwlwifi patch dependency.
Major changes:
iwlwifi
* implement Traffic Condition Monitor and use it for scan, BT coex and
to detect when the AP doesn't support UAPSD properly
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload
qtnfmac
* DFS offload support
rsi
* roaming enhancements
* increase max supported aggregation subframes
* don't advertise 5 GHz support if the device doesn't support it
brcmfmac
* add support for BCM4366E chipset
* add support for bcm43364 wireless chipset
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As documented in Documentation/timers/timers-howto.txt,
replace msleep(1) with usleep_range().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce an new common helper to avoid redundancy.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The early versions of am33xx devices, related to ES1.0 SoC revision
have errata limiting mq support. That's the same errata as
commit 7da1160002f1 ("drivers: net: cpsw: add am335x errata workarround for
interrutps")
AM33xx Errata [1] Advisory 1.0.9
http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
After additional investigation were found that drivers w/a is
propagated on all AM33xx SoCs and on DM814x. But the errata exists
only for ES1.0 of AM33xx family, limiting mq support for revisions
after ES1.0. So, disable mq support only for related SoCs and use
separate polls for revisions allowing mq.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not necessary to disable interrupt lines here during a reset
to handle a non-fatal firmware error. Move that call within the code
block that handles the other cases that do require interrupts to be
disabled and re-enabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the firmware map fails for whatever reason, remember to free
up the memory after.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the NVM read/erase/update AQ commands to align with
the latest specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set hw->mac.perm_addr in ixgbevf_set_mac() in order to avoid losing the
custom MAC on reset. This can happen in the following case:
>ip link set $vf address $mac
>ethtool -r $vf
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Do not validate the MAC address during a reset, unless the MAC was set on
the host. This way the VF will get a new MAC address every time it reloads.
Remove the "no MAC address assigned" message since it will get spammed on
reset and it doesn't help much as the MAC on the VF is randomly generated.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently, during device_shutdown() ixgbe holds rtnl_lock for the duration
of lengthy ixgbe_close_suspend(). On machines with multiple ixgbe cards
this lock prevents scaling if device_shutdown() function is multi-threaded.
It is not necessary to hold this lock during ixgbe_close_suspend()
as it is not held when ixgbe_close() is called also during shutdown but for
kexec case.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since commit f7f37e7ff2b9 ("ixgbe: handle close/suspend race with
netif_device_detach/present") ixgbe_close_suspend is called, from
ixgbe_close, only if the device is present, i.e. if it isn't detached.
That exposed a situation where IRQs weren't freed if a PCI error
recovery system opts to remove the device. For such case the pci channel
state is set to pci_channel_io_perm_failure and ixgbe_io_error_detected
was returning PCI_ERS_RESULT_DISCONNECT before calling
ixgbe_close_suspend consequentially not freeing IRQ and crashing when
the remove handler calls pci_disable_device, hitting a BUG_ON at
free_msi_irqs, which asserts that there is no non-free IRQ associated
with the device to be removed:
BUG_ON(irq_has_action(entry->irq + i));
The issue is fixed by calling the ixgbe_close_suspend before evaluate
the pci channel state.
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Sparse complains valid conversions between restricted types, force
attribute is used to avoid those warnings.
Signed-off-by: Cathy Zhou <cathy.zhou@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch introduces support for the MPLS flow spec and
allows the creation of rules that are matching on the
MPLS label.
Applying the rule matching depends on the flow specs order and
the location of the MPLS in the spec list as there are different
configurations to be made in the device in the cases of MPLSoGRE
and MPLSoUDP vs. non-encapsulated MPLS.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 'kvzalloc()' is used to allocate memory, 'kvfree()' must be used to
free it.
Fixes: fed9ce22bf8ae ("net/mlx5: E-Switch, Add API to create vport rx rules")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When 'kvzalloc()' is used to allocate memory, 'kvfree()' must be used to
free it.
Fixes: 9efa75254593d ("net/mlx5_core: Introduce access functions to query vport RoCE fields")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For T6, clip table is separated from main TCAM. So, update LE-TCAM
collection logic to collect clip table TCAM as well. IPv6 takes
4 entries in clip table TCAM compared to 2 entries in main TCAM.
Also, in case of errors, keep LE-TCAM collected so far and set the
status to partial dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
