| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Use the return value of dma_map_single(), rather than calling
virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers. This is unsafe because:
- In general, register writes are not serialised with DMA, so we still
have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
RX DMA at the next packet boundary
I applied this patch to the driver to detect DMA writes to freed
buffers:
> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
> /* Free Rx skb ringbuffer */
> if (mdp->rx_skbuff) {
> for (i = 0; i < mdp->num_rx_ring; i++)
> + memcpy(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12);
> + msleep(100);
> + for (i = 0; i < mdp->num_rx_ring; i++) {
> + WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12));
> dev_kfree_skb(mdp->rx_skbuff[i]);
> + }
> }
> kfree(mdp->rx_skbuff);
> mdp->rx_skbuff = NULL;
then ran the loop:
while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine. The
warning fired several times a minute.
To fix these issues:
- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
frame, disable egress and wait a reasonable time to reach a
packet boundary before resetting
- Update statistics before resetting
(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse. These errors are visible in the
statistics anyway.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While being in an ERROR_WARNING state, and receiving further
bus error events with error counters still in the ERROR_WARNING
range of 97-127 inclusive, the state handling code erroneously
reverts back to ERROR_ACTIVE.
Per the CAN standard, only revert to ERROR_ACTIVE when the
error counters are less than 96.
Moreover, in certain Kvaser models, the BUS_ERROR flag is
always set along with undefined bits in the M16C status
register. Thus use bitwise operators instead of full equality
for checking that register against bus errors.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On some x86 laptops, plugging a Kvaser device again after an
unplug makes the firmware always ignore the very first command.
For such a case, provide some room for retries instead of
completely exiting the driver init code.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Send expected argument to the URB completion hander: a CAN
netdevice instead of the network interface private context
`kvaser_usb_net_priv'.
This was discovered by having some garbage in the kernel
log in place of the netdevice names: can0 and can1.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upon receiving a hardware event with the BUS_RESET flag set,
the driver kills all of its anchored URBs and resets all of
its transmit URB contexts.
Unfortunately it does so under the context of URB completion
handler `kvaser_usb_read_bulk_callback()', which is often
called in an atomic context.
While the device is flooded with many received error packets,
usb_kill_urb() typically sleeps/reschedules till the transfer
request of each killed URB in question completes, leading to
the sleep in atomic bug. [3]
In v2 submission of the original driver patch [1], it was
stated that the URBs kill and tx contexts reset was needed
since we don't receive any tx acknowledgments later and thus
such resources will be locked down forever. Fortunately this
is no longer needed since an earlier bugfix in this patch
series is now applied: all tx URB contexts are reset upon CAN
channel close. [2]
Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF
event, which is the recommended handling method advised by
the device manufacturer.
[1] http://article.gmane.org/gmane.linux.network/239442
http://www.webcitation.org/6Vr2yagAQ
[2] can: kvaser_usb: Reset all URB tx contexts upon channel close
889b77f7fd2bcc922493d73a4c51d8a851505815
[3] Stacktrace:
<IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57
[<ffffffff8158b60c>] __schedule_bug+0x41/0x4f
[<ffffffff815904b1>] __schedule+0x5f1/0x700
[<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10
[<ffffffff81590684>] schedule+0x24/0x70
[<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0
[<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110
[<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80
[<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb]
[<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb]
[<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20
[<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb]
[<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0
[<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110
[<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd]
[<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20
[<ffffffff81069f65>] ? local_clock+0x15/0x30
[<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd]
[<ffffffff814fbb31>] ? process_backlog+0xb1/0x130
[<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd]
[<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30
[<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120
[<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60
[<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110
[<ffffffff81004dfd>] handle_irq+0x1d/0x30
[<ffffffff81004727>] do_IRQ+0x57/0x100
[<ffffffff8159482a>] common_interrupt+0x6a/0x6a
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Commit 69ad0dd7af22b61d9e0e68e56b6290121618b0fb
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon May 19 13:59:59 2014 -0300
net: mv643xx_eth: Use dma_map_single() to map the skb fragments
caused a nasty regression by removing the support for highmem skb
fragments. By using page_address() to get the address of a fragment's
page, we are assuming a lowmem page. However, such assumption is incorrect,
as fragments can be in highmem pages, resulting in very nasty issues.
This commit fixes this by using the skb_frag_dma_map() helper,
which takes care of mapping the skb fragment properly. Additionally,
the type of mapping is now tracked, so it can be unmapped using
dma_unmap_page or dma_unmap_single when appropriate.
This commit also fixes the error path in txq_init() to release the
resources properly.
Fixes: 69ad0dd7af22 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments")
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Dual EMAC, the default VLANs are used to segregate Rx packets between
the ports, so adding the same default VLAN to the switch will affect the
normal packet transfers. So returning error on addition of dual EMAC
default VLANs.
Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to
break dual EMAC port separations.
Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation)
Cc: <stable@vger.kernel.org> # v3.9+
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-21
this is a pull request for v3.19, net/master, which consists of a single patch.
Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface
might continue to send frames after the interface has been shut down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip6_route_output() always returns a valid dst pointer unlike in IPv4
case. So the validation has to be different from the IPv4 path. Correcting
that error in this patch.
This was picked up by a static checker with a following warning -
drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound()
warn: 'dst' isn't an ERR_PTR
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.
If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
ath9k:
* fix an IRQ storm caused by commit 872b5d814f99
iwlwifi:
* A fix for scan that fixes a firmware assertion
* A fix that improves roaming behavior. Same fix has been tested for
a while in iwldvm. This is a bit of a work around, but the real fix
should be in mac80211 and will come later.
* A fix for BARs that avoids a WARNING.
* one fix for rfkill while scheduled scan is running.
Linus's system hit this issue. WiFi would be unavailable
after this has happpened because of bad state in cfg80211.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updated hardware documention shows the Rx flow control settings were
moved from the Rx queue operation mode register to a new Rx queue flow
control register. The old flow control settings are now reserved areas
of the Rx queue operation mode register. Update the code to use the new
register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Put controller into init mode in network stop to end pending transmissions. The
issue is observed in cases when transmitted frame is not acked.
Signed-off-by: Viktor Babrian <babrian.viktor@renyi.mta.hu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we
used all 15 characters then the sprintf() would overflow.
I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as
well, even though it can't overflow just to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read OCP register 0xa43a~0xa43b would clear some flags which the hw
would use, and it may let the device lost. However, the unit of
reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling
sram_read() to read OCP_SRAM_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read()
which is used to read the whole 4 byte data, keep the unchanged bytes,
and modify the expected bytes. However, the "byen" could be used to
determine which bytes of the 4 bytes to write, so the action could be
removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi should get registered before the netdev and not after.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To fix invalid hardware accesses, the commit 872b5d814f99 ("ath9k: do not
access hardware on IRQs during reset") made the irq handler ignore interrupts
emitted after queueing a hardware reset (which disables the IRQ). This left a
small time window for the IRQ to get re-enabled by the tasklet, which caused
IRQ storms. Instead of returning IRQ_NONE when ATH_OP_HW_RESET is set, disable
the IRQ entirely for the duration of the reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* one fix for rfkill while scheduled scan is running.
Linus's system hit this issue. WiFi would be unavailable
after this has happpened because of bad state in cfg80211.
|
|
When we have an active scheduled scan, and the RFKILL
interrupt kicks in, the stack will cancel the scheduled
scan as part of the down flow. But cancelling scheduled
scan usually implies sending a command to the firwmare
which has been killed as part of the RFKILL interrupt
handling.
Because of that, we returned an error to mac80211 when
it asked to stop the scheduled scan and didn't notify the
end of the scheduled scan. Besides a fat warning, this led
to a situation in which cfg80211 would refuse any new scan
request.
To disentangle this, fake that the scheduled scan has been
stopped without sending the command to the firwmare, return
0 after having properly let cfg80211 know that the scan
has been cancelled.
This is basically the same as:
commit 9b520d84957d63348e87c0f2cbd21d86e1e8f2f2
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Tue Nov 4 15:54:11 2014 +0200
iwlwifi: mvm: abort scan upon RFKILL
This code existed but not for all the different FW APIs
we support.
Fix this.
but for the scheduled scan case.
Link: http://permalink.gmane.org/gmane.linux.kernel.wireless.general/133232
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
On dm816x we have two emac controllers with separate memory
areas.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
space
Some devices like dm816x have the MDIO registers within the first EMAC
instance address space. Let's fix the issue by allowing to pass an
optional second IO range for the EMAC control register area.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like the phy_id is never set up beyond getting the phandle.
Note that we can remove the ifdef for phy_node as there is a stub
for of_phy_connec() if CONFIG_OF is not set.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only use clk_get() to get the frequency, the rest is done by
the runtime PM calls. Let's free the clock too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ba97381343b ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On davinci_emac, we have pulse interrupts. This means that we need to
clear the EOI bits when disabling interrupts as otherwise the interrupts
keep happening. And we also need to not clear the EOI bits again when
enabling the interrupts as otherwise we will get tons of:
unexpected IRQ trap at vector 00
These errors almost certainly mean that the omap-intc.c is signaling
a spurious interrupt with the reserved irq 127 as we've seen earlier
on omap3.
Let's fix the issue by clearing the EOI bits when disabling the
interrupts. Let's also keep the comment for "Rx Threshold and Misc
interrupts are not enabled" for both enable and disable so people
are aware of this when potentially adding more support.
Note that eventually we should handle the RX and TX interrupts
separately like cpsw is now doing. However, so far I have not seen
any issues with this based on my testing, so it seems to behave a
little different compared to the cpsw that had a similar issue.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-01-15
this is a pull request of 8 patches.
Ahmed S. Darwish contributes 4 fixes for the kvaser_usb driver. The two patches
by Oliver Hartkopp mark the m_can driver as non-ISO, as the CANFD standard was
updated. Roger Quadros's patch for the c_can driver fixes the register access
during RAMINIT. And one patch by my, which updates the MAINTAINERS file, as we
moved the git repos to the kernel.org infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Except for VXLAN steering rules, all offloads should work as they were
under plain DMFS mode. Fix that by enabling all the offloads under
DMFS-A0 mode, except for VXLAN steering rules.
Fixes: d57febe1a478 "net/mlx4: Add A0 hybrid steering"
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes double kfree() calls at init_rx_ring() because
it causes static checker warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the MAC address is provided in the device tree file, the
condition is true and kernel crashes due to NULL dereference.
Signed-off-by: Girish K.S <ks.giri@samsung.com>
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit b284fbe3b3ef9cf8 ("sh_eth: Fix access to TRSCER register") wanted
to add a .trscer_err_mask value to the R-Car Gen2 family-specific data
structure (r8a779x_data), but it was accidentally added to the
SH7724-specific data structure (sh7724_data).
Presumably this happened due to a patch conflict with commit
d407bc0203539031 ("sh-eth: Set fdr_value of R-Car SoCs"), which added
another field at the same position.
Move the field setting to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: b284fbe3b3ef9cf8 ("sh_eth: Fix access to TRSCER register")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
while adding vlan in dual EMAC mode, only specific ports should be
subscribed for the vlan, else it will lead to switching mode and
if both ports connected to same switch cpsw will hung as it creates
a network loop. Fixing this by adding only specific ports in case
of dual EMAC.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not touch the packet after a netif_rx: it might
get freed behind our back.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
