summaryrefslogtreecommitdiff
path: root/drivers/net/wireless
AgeCommit message (Collapse)AuthorFilesLines
2011-01-19ath9k_hw: fix carrier leakage calibration for AR9271Rajkumar Manoharan1-1/+4
AR9285 carrier leakage calibration related workaround on high temperature is not applicable for AR9271. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k_htc: keep calibrated noise floor value for oper channelRajkumar Manoharan2-4/+5
The ath9k_hw assumes that caldata is valid only for oper channel. But with ath9k_htc case, the caldata is passed for all channels on hw_reset though we are not doing calibration on that channel. So the oper channel's nf history got cleared to default due to mismatch in channel flags. This patch also saves some space. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k: preserve caldata history buffer across scanningRajkumar Manoharan1-3/+2
caldata's channel info is never filled with operating channel info which is causing the operating channel's noise floor history buffer is reset to default nf during channel change. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k_hw: partially revert "fix dma descriptor rx error bit parsing"Felix Fietkau2-8/+14
The rx error bit parsing was changed to consider PHY errors and various decryption errors separately. While correct according to the documentation, this is causing spurious decryption error reports in some situations. Fix this by restoring the original order of the checks in those places, where the errors are meant to be mutually exclusive. If a CRC error is reported, then MIC failure and decryption errors are irrelevant, and a PHY error is unlikely. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath5k: Fix return codes for eeprom read functions.Wojciech Dubowik4-26/+19
Eeprom read functions are of bool type and not int. Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k: reduce the likelihood of baseband hang check false positivesFelix Fietkau1-1/+12
Since baseband hangs are rare, but the hang check function has a high false positive rate in some situations, we need to add more reliable indicators. In AP mode we can use blocked beacon transmissions as an indicator, they should be rare enough. In station mode, we can skip the hang check entirely, since a true hang will trigger beacon loss detection, and mac80211 will rescan, which leads to a hw reset that will bring the hardware back to life. To make this more reliable, we need to skip fast channel changes if the hardware appears to be stuck. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k: reinitialize block ack window data when starting aggregationFelix Fietkau1-0/+3
There might be some old stale data left, which could confuse tracking of pending tx frames. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k: fix initial sequence number after starting an ampdu sessionFelix Fietkau1-1/+1
txtid->seq_start may not always be up to date, when there is HT non-AMPDU traffic just before starting an AMPDU session. Relying on txtid->seq_next is better, since it is also used to generate the sequence numbers for all QoS data frames. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k: fix bogus sequence number increases on aggregation tid flushFelix Fietkau1-1/+1
When a tid pointer is passed to ath_tx_send_normal(), it increases the starting sequence number for the next AMPDU action frame, which should only be done if the sequence number assignment is fresh. In this case it is clearly not. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090RA-Jay Hung2-8/+23
Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value when call rt2800_init_rfcsr Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19rt2x00: Fix radio off hang issue for PCIE interfaceRA-Jay Hung2-32/+10
PCI/PCIE radio off behavior is different from SOC/USB. They mainly use MCU command to disable DMA, TX/RX and enter power saving mode. Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k_hw: Offload USB eeprom reading to targetSujith Manoharan5-29/+123
For USB devices, reading the EEPROM data can be offloaded to the target. Use multiple register reads to take advantage of this feature to reduce initialization time. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19ath9k_htc: Add multiple register read APISujith Manoharan3-0/+34
This would decrease latency in reading bulk registers. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19mwl8k: Enable HW encryption for AP modeNishant Sarmukadam1-3/+277
set_key callback is defined for mac80211 to install keys for HW crypto in AP mode. Driver currently falls back to SW crypto in STA mode. Add support to configure the keys appropriately in the hardware after the set_key routine is called. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19mwl8k: Set mac80211 rx status flags appropriately when hw crypto is enabledNishant Sarmukadam1-3/+98
When hw crypto is enabled, set rx status flags appropriately depending on whether hw crypto is enabled for a particular bss. Also report MIC errors to mac80211, so that counter measures can be initiated Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: yogesh powar <yogeshp@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19mwl8k: Add encapsulation of data packet for cryptoNishant Sarmukadam1-1/+53
Different tail pads will be needed for crypto depending on the crypto mode. Add support to encapsulate the packets with appropriate pad value. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-19mwl8k: Modify add_dma_header to include pad parametersNishant Sarmukadam1-6/+10
Add capability to add_dma_header to support padding at tail of the data packet to be transmitted when crypto is enabled. Padding is required for adding crypto information in data packets for supporting 802.11 security modes. Signed-off-by: Nishant Sarmukadam <nishants@marvell.com> Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com> Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18iwlwifi: fix valid chain reading from EEPROMWey-Yi Guy1-1/+1
When read valid tx/rx chains from EEPROM, there is a bug to use the tx chain value for both tx and rx, the result of this cause low receive throughput on 1x2 devices becuase rx will only utilize single chain instead of two chains Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18ath5k: fix locking in tx_complete_poll_workBob Copeland1-0/+4
ath5k_reset must be called with sc->lock. Since the tx queue watchdog runs in a workqueue and accesses sc, it's appropriate to just take the lock over the whole function. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18ath9k_hw: do PA offset calibration only on longcal intervalRajkumar Manoharan1-5/+5
The power detector adc offset calibration has to be done on 4 minutes interval (longcal * pa_skip_count). But the commit "ath9k_hw: fix a noise floor calibration related race condition" makes the PA calibration executed more frequently beased on nfcal_pending value. Running PAOffset calibration lesser than longcal interval doesn't help anything and the worse part is that it causes NF load timeouts and RX deaf conditions. In a very noisy environment, where the distance b/w AP & station is ~10 meter and running a downlink udp traffic with frequent background scan causes "Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state. This issue was originaly reported in Android platform where the network-manager application does bgscan more frequently on AR9271 chips. (AR9285 family usb device). Cc: stable@kernel.org Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18ath9k_htc: Fix endian issue in tx headerRajkumar Manoharan2-4/+6
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-18ath9k_hw: ASPM interoperability fix for AR9380/AR9382Luis R. Rodriguez2-3/+3
There is an interoperability with AR9382/AR9380 in L1 state with a few root complexes which can cause a hang. This is fixed by setting some work around bits on the PCIE PHY. We fix by using a new ini array to modify these bits when the radio is idle. Cc: stable@kernel.org Cc: Jack Lee <jack.lee@atheros.com> Cc: Carl Huang <carl.huang@atheros.com> Cc: David Quan <david.quan@atheros.com> Cc: Nael Atallah <nael.atallah@atheros.com> Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds8-23/+51
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits) GRETH: resolve SMP issues and other problems GRETH: handle frame error interrupts GRETH: avoid writing bad speed/duplex when setting transfer mode GRETH: fixed skb buffer memory leak on frame errors GRETH: GBit transmit descriptor handling optimization GRETH: fix opening/closing GRETH: added raw AMBA vendor/device number to match against. cassini: Fix build bustage on x86. e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs e1000e: update Copyright for 2011 e1000: Avoid unhandled IRQ r8169: keep firmware in memory. netdev: tilepro: Use is_unicast_ether_addr helper etherdevice.h: Add is_unicast_ether_addr function ks8695net: Use default implementation of ethtool_ops::get_link ks8695net: Disable non-working ethtool operations USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable. vxge: Remember to release firmware after upgrading firmware netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr ipsec: update MAX_AH_AUTH_LEN to support sha512 ...
2011-01-14Merge branch 'linux-next' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6 * 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: PCI/PM: Report wakeup events before resuming devices PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events PCI: sysfs: Update ROM to include default owner write access x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available PCI/ACPI: Request _OSC control once for each root bridge (v3) PCI: enable pci=bfsort by default on future Dell systems PCI/PCIe: Clear Root PME Status bits early during system resume PCI: pci-stub: ignore zero-length id parameters x86/PCI: irq and pci_ids patch for Intel Patsburg PCI: Skip id checking if no id is passed PCI: fix __pci_device_probe kernel-doc warning PCI: make pci_restore_state return void PCI: Disable ASPM if BIOS asks us to PCI: Add mask bit definition for MSI-X table PCI: MSI: Move MSI-X entry definition to pci_regs.h Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the meantime been converted to not use legacy PCI power management, and thus no longer use pci_restore_state() at all (and that caused trivial conflicts with the "make pci_restore_state return void" patch)
2011-01-13rt2x00: Don't leak mem in error path of rt2x00lib_request_firmware()Jesper Juhl1-0/+1
We need to release_firmware() in order not to leak memory. Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Pekka Enberg <penberg@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-13iwmc3200wifi: Return proper error for iwm_if_allocAxel Lin1-0/+2
In the case of alloc_netdev_mq failure and kmalloc failure, current implementation returns ERR_PTR(0). As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR macro. Fix it by setting proper error code for ret variable in the failure cases. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-13Merge branch 'for-next' of ↵Linus Torvalds15-23/+23
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits) Documentation/trace/events.txt: Remove obsolete sched_signal_send. writeback: fix global_dirty_limits comment runtime -> real-time ppc: fix comment typo singal -> signal drivers: fix comment typo diable -> disable. m68k: fix comment typo diable -> disable. wireless: comment typo fix diable -> disable. media: comment typo fix diable -> disable. remove doc for obsolete dynamic-printk kernel-parameter remove extraneous 'is' from Documentation/iostats.txt Fix spelling milisec -> ms in snd_ps3 module parameter description Fix spelling mistakes in comments Revert conflicting V4L changes i7core_edac: fix typos in comments mm/rmap.c: fix comment sound, ca0106: Fix assignment to 'channel'. hrtimer: fix a typo in comment init/Kconfig: fix typo anon_inodes: fix wrong function name in comment fix comment typos concerning "consistent" poll: fix a typo in comment ... Fix up trivial conflicts in: - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c) - fs/ext4/ext4.h Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-10hostap_cs: fix sleeping function called from invalid contextStanislaw Gruszka1-9/+6
pcmcia_request_irq() and pcmcia_enable_device() are intended to be called from process context (first function allocate memory with GFP_KERNEL, second take a mutex). We can not take spin lock and call them. It's safe to move spin lock after pcmcia_enable_device() as we still hold off IRQ until dev->base_addr is 0 and driver will not proceed with interrupts when is not ready. Patch resolves: https://bugzilla.redhat.com/show_bug.cgi?id=643758 Reported-and-tested-by: rbugz@biobind.com Cc: stable@kernel.org # 2.6.34+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ipw2200: Check for -1 INTA in tasklet too.Indan Zupancic1-0/+7
This is an attempt to fix a long standing open bug: http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334 The interrupt handler checks for INTA being -1, apparently that means that the hardware is gone. But the interrupt handler defers actual interrupt processing to a tasklet. By the time the tasklet is run and checks INTA again, the hardware might be gone and INTA be -1, which confuses the driver because all event bits are set. The patch applies to 2.6.37. Signed-off-by: Indan Zupancic <indan@nul.nu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10p54: fix sequence no. accounting off-by-one errorChristian Lamparter1-1/+1
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the firmware that "the frame's sequence number has already been set by the application." Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for frames which lack a valid sequence number and either the driver or firmware has to assign one. Yup, it's the exact opposite! Cc: <stable@kernel.org> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_htc: Really fix packet injectionSujith Manoharan2-11/+27
The chainmask value along with other configuration has to be set on the target for packet injection. Fix this and also move the monitor interface addition before the channel set segment to ensure that the opmode is updated properly. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix RX handling for USB devicesSujith Manoharan1-1/+1
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset" uncondionally added aborting RX DMA in a HW reset, though it is a bit unclear as to why this is needed. Anyway, RX DMA is handled in the target for USB devices, and this would interfere with normal operations (scanning etc.), so fix this. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix thermal issue with UB94Sujith Manoharan1-0/+4
Hardcode the output voltage of x-PA bias LDO to the lowest value for UB94. The card doesn't get too hot now. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix calibration for AR9287 devicesSujith Manoharan1-0/+3
AR9287 based devices have issues with ADC gain calibration which would cause uplink throughput drops in HT40 mode. Remove ADC gain from the supported calibration algorithms. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-10ath9k_hw: Fix chip testSujith Manoharan1-1/+2
USB devices do not require the chip test routine. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-08Merge branch 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wqLinus Torvalds1-2/+1
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits) usb: don't use flush_scheduled_work() speedtch: don't abuse struct delayed_work media/video: don't use flush_scheduled_work() media/video: explicitly flush request_module work ioc4: use static work_struct for ioc4_load_modules() init: don't call flush_scheduled_work() from do_initcalls() s390: don't use flush_scheduled_work() rtc: don't use flush_scheduled_work() mmc: update workqueue usages mfd: update workqueue usages dvb: don't use flush_scheduled_work() leds-wm8350: don't use flush_scheduled_work() mISDN: don't use flush_scheduled_work() macintosh/ams: don't use flush_scheduled_work() vmwgfx: don't use flush_scheduled_work() tpm: don't use flush_scheduled_work() sonypi: don't use flush_scheduled_work() hvsi: don't use flush_scheduled_work() xen: don't use flush_scheduled_work() gdrom: don't use flush_scheduled_work() ... Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c as per Tejun.
2011-01-06Merge branch 'master' of ↵John W. Linville82-1501/+5036
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: net/bluetooth/Makefile
2011-01-05ath9k: correct MODULE_PARM_DESC parameters for force_new_aniJohn W. Linville1-1/+1
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05ath5k: qualify global modparam_nohwcrypt variableJohn W. Linville2-4/+4
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05ath9k: qualify global modparam_nohwcrypt variableJohn W. Linville3-5/+5
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-05Merge branch 'master' of ↵John W. Linville3-5/+11
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-01-04libertas: down_interruptible() can return -EINTR, not EINTRroel kluin1-1/+1
Fix test in lbs_spi_thread(). down_interruptible() can return -EINTR, but not EINTR. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Fix packet injectionSujith Manoharan1-8/+64
To inject a packet in monitor mode, a dummy station has to be associated with the monitor interface in the target. Failing to do this would result in a firmware crash on the device. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath5k: ath5k_eeprom_mode_from_channel() returns signedDan Carpenter1-2/+4
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing the result in "ee_mode" which is an unsigned char. This breaks the error handling. This patch makes "ee_mode" an int. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k : few rate control clean upsMohammed Shafi Shajakhan2-11/+8
Remove some obvious looking dead code and rename few functions Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k: fix beacon restart on channel changeRajkumar Manoharan1-1/+2
Restart the beacon timers only if the beacon was already configured. Otherwise beacons timers are restarted unnecessarily in unassociated state too. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04Revert "ath9k: Parse DTIM period from mac80211"Mohammed Shafi Shajakhan2-4/+2
This reverts commit 0ce3bcfc84900a64347b0fe1140229bd81314008. Event though with the above commit we obtain the configured DTIM period from the AP rather than always hardcoding it to '1', this seems to cause problems under the following scenarios: * Preventing association with broken AP's * Adds latency in roaming So its better to always use the safe value of '1' for dtim period Cc: Jouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_hw: fix dma descriptor rx error bit parsingFelix Fietkau2-9/+11
An Rx DMA descriptor can have multiple error bits set, and some error bits (e.g. MIC failure) are filtered by the driver based on other criteria. Remove the 'else' in various error bit checks so that all error information is properly passed to the driver. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Move LED/RFKILL code to htc_drv_gpio.cSujith Manoharan3-312/+333
And add the copyright/license header. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-04ath9k_htc: Fix fast channel changeSujith Manoharan2-16/+11
When returning to the operating channel, a full HW reset has to be done instead of a fast channel change. Since sw_scan_complete() is called after the config() call for the home channel, we end up doing a FCC. Fix this issue by checking the OFFCHANNEL flag to determine FCC. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>