summaryrefslogtreecommitdiff
path: root/drivers/net/usb/rndis_host.c
AgeCommit message (Collapse)AuthorFilesLines
2017-10-04rndis_host: support Novatel Verizon USB730LAleksander Morgado1-0/+4
Treat the ef/04/01 interface class/subclass/protocol combination used by the Novatel Verizon USB730L (1410:9030) as a possible RNDIS interface. T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 17 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 3 P: Vendor=1410 ProdID=9030 Rev=03.10 S: Manufacturer=Novatel Wireless S: Product=MiFi USB730L S: SerialNumber=0123456789ABCDEF C: #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid Once the network interface is brought up, the user just needs to run a DHCP client to get IP address and routing setup. As a side note, other Novatel Verizon USB730L models with the same vid:pid end up exposing a standard ECM interface which doesn't require any other kernel update to make it work. Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16networking: make skb_push & __skb_push return void pointersJohannes Berg1-1/+1
It seems like a historic accident that these return unsigned char *, and in many places that means casts are required, more often than not. Make these functions return void * and remove all the casts across the tree, adding a (u8 *) cast only where the unsigned char pointer was used directly, all done with the following spatch: @@ expression SKB, LEN; typedef u8; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - *(fn(SKB, LEN)) + *(u8 *)fn(SKB, LEN) @@ expression E, SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; type T; @@ - E = ((T *)(fn(SKB, LEN))) + E = fn(SKB, LEN) @@ expression SKB, LEN; identifier fn = { skb_push, __skb_push, skb_push_rcsum }; @@ - fn(SKB, LEN)[0] + *(u8 *)fn(SKB, LEN) Note that the last part there converts from push(...)[0] to the more idiomatic *(u8 *)push(...). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-04net: usbnet: support 64bit statsGreg Ungerer1-0/+1
Add support for the net stats64 counters to the usbnet core. With that in place put the hooks into every usbnet driver to use it. This is a strait forward addition of 64bit counters for RX and TX packet and byte counts. It is done in the same style as for the other net drivers that support stats64. Note that the other stats fields remain as 32bit sized values (error counts, etc). The motivation to add this is that it is not particularly difficult to get the RX and TX byte counts to wrap on 32bit platforms. Signed-off-by: Greg Ungerer <gerg@linux-m68k.org> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-28lib/vsprintf.c: remove %Z supportAlexey Dobriyan1-1/+1
Now that %z is standartised in C99 there is no reason to support %Z. Unlike %L it doesn't even make format strings smaller. Use BUILD_BUG_ON in a couple ATM drivers. In case anyone didn't notice lib/vsprintf.o is about half of SLUB which is in my opinion is quite an achievement. Hopefully this patch inspires someone else to trim vsprintf.c more. Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-07-17rndis_host: Set valid random MAC on buggy devicesKristian Evensen1-1/+5
Some devices of the same type all export the same, random MAC address. This behavior has been seen on the ZTE MF910, MF823 and MF831, and there are probably more devices out there. Fix this by generating a valid random MAC address if we read a random MAC from device. Also, changed the memcpy() to ether_addr_copy(), as pointed out by checkpatch. Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-02-17usbnet: remove generic hard_header_len checkEmil Goode1-0/+4
This patch removes a generic hard_header_len check from the usbnet module that is causing dropped packages under certain circumstances for devices that send rx packets that cross urb boundaries. One example is the AX88772B which occasionally send rx packets that cross urb boundaries where the remaining partial packet is sent with no hardware header. When the buffer with a partial packet is of less number of octets than the value of hard_header_len the buffer is discarded by the usbnet module. With AX88772B this can be reproduced by using ping with a packet size between 1965-1976. The bug has been reported here: https://bugzilla.kernel.org/show_bug.cgi?id=29082 This patch introduces the following changes: - Removes the generic hard_header_len check in the rx_complete function in the usbnet module. - Introduces a ETH_HLEN check for skbs that are not cloned from within a rx_fixup callback. - For safety a hard_header_len check is added to each rx_fixup callback function that could be affected by this change. These extra checks could possibly be removed by someone who has the hardware to test. - Removes a call to dev_kfree_skb_any() and instead utilizes the dev->done list to queue skbs for cleanup. The changes place full responsibility on the rx_fixup callback functions that clone skbs to only pass valid skbs to the usbnet_skb_return function. Signed-off-by: Emil Goode <emilgoode@gmail.com> Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-16drivers/net: delete non-required instances of include <linux/init.h>Paul Gortmaker1-1/+0
None of these files are actually using any __init type directives and hence don't need to include <linux/init.h>. Most are just a left over from __devinit and __cpuinit removal, or simply due to code getting copied from one driver to the next. This covers everything under drivers/net except for wireless, which has been submitted separately. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-12-06usb: Fix FSF address in file headersJeff Kirsher1-2/+1
Several files refer to an old address for the Free Software Foundation in the file header comment. Resolve by replacing the address with the URL <http://www.gnu.org/licenses/> so that we do not have to keep updating the header comments anytime the address changes. CC: Oliver Neukum <oliver@neukum.org> CC: Steve Glendinning <steve.glendinning@shawell.net> CC: Oliver Neukum <oneukum@suse.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-09remove init of dev->perm_addr in driversJiri Pirko1-1/+0
perm_addr is initialized correctly in register_netdevice() so to init it in drivers is no longer needed. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-23Merge tag 'usb-3.5-rc1' of ↵Linus Torvalds1-0/+1
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB 3.5-rc1 changes from Greg Kroah-Hartman: "Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window. It's touches a lot of different parts of the kernel, all USB drivers, due to some API cleanups (getting rid of the ancient err() macro) and some changes that are needed for USB 3.0 power management updates. There are also lots of new drivers, pimarily gadget, but others as well. We deleted a staging driver, which was nice, and finally dropped the obsolete usbfs code, which will make Al happy to never have to touch that again. There were some build errors in the tree that linux-next found a few days ago, but those were fixed by the most recent changes (all were due to us not building with CONFIG_PM disabled.) Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>" * tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits) xhci: Fix DIV_ROUND_UP compile error. xhci: Fix compile with CONFIG_USB_SUSPEND=n USB: Fix core compile with CONFIG_USB_SUSPEND=n brcm80211: Fix compile error for .disable_hub_initiated_lpm. Revert "USB: EHCI: work around bug in the Philips ISP1562 controller" MAINTAINERS: Add myself as maintainer to the USB PHY Layer USB: EHCI: fix command register configuration lost problem USB: Remove races in devio.c USB: ehci-platform: remove update_device USB: Disable hub-initiated LPM for comms devices. xhci: Add Intel U1/U2 timeout policy. xhci: Add infrastructure for host-specific LPM policies. USB: Add macros for interrupt endpoint types. xhci: Reserve one command for USB3 LPM disable. xhci: Some Evaluate Context commands must succeed. USB: Disable USB 3.0 LPM in critical sections. USB: Add support to enable/disable USB3 link states. USB: Allow drivers to disable hub-initiated LPM. USB: Calculate USB 3.0 exit latencies for LPM. USB: Refactor code to set LPM support flag. ... Conflicts: arch/arm/mach-exynos/mach-nuri.c arch/arm/mach-exynos/mach-universal_c210.c drivers/net/wireless/ath/ath6kl/usb.c
2012-05-19USB: Disable hub-initiated LPM for comms devices.Sarah Sharp1-0/+1
Hub-initiated LPM is not good for USB communications devices. Comms devices should be able to tell when their link can go into a lower power state, because they know when an incoming transmission is finished. Ideally, these devices would slam their links into a lower power state, using the device-initiated LPM, after finishing the last packet of their data transfer. If we enable the idle timeouts for the parent hubs to enable hub-initiated LPM, we will get a lot of useless LPM packets on the bus as the devices reject LPM transitions when they're in the middle of receiving data. Worse, some devices might blindly accept the hub-initiated LPM and power down their radios while they're in the middle of receiving a transmission. The Intel Windows folks are disabling hub-initiated LPM for all USB communications devices under a xHCI USB 3.0 host. In order to keep the Linux behavior as close as possible to Windows, we need to do the same in Linux. Set the disable_hub_initiated_lpm flag for for all USB communications drivers. I know there aren't currently any USB 3.0 devices that implement these class specifications, but we should be ready if they do. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Gustavo Padovan <gustavo@padovan.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: Hansjoerg Lipp <hjlipp@web.de> Cc: Tilman Schmidt <tilman@imap.cc> Cc: Karsten Keil <isdn@linux-pingi.de> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Jan Dumon <j.dumon@option.com> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com> Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: Brett Rudley <brudley@broadcom.com> Cc: Roland Vossen <rvossen@broadcom.com> Cc: Arend van Spriel <arend@broadcom.com> Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com> Cc: Kan Yan <kanyan@broadcom.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Daniel Drake <dsd@gentoo.org> Cc: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-12rndis_host: cleanup: change oid from __le32 to u32 in rndis_query()Jussi Kivilinna1-6/+6
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-12rndis_host: cleanup: byteswap data from device instead of RNDIS_* definesJussi Kivilinna1-25/+28
All other values from device provided buffer are byteswapped, so it seems more logical to do same for these. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-12usb/net: rndis: eliminate first set of duplicate OIDsLinus Walleij1-3/+3
The RNDIS protocol contains a vast number of Object ID:s (OIDs). The current definitions had multiple definitions of these ID:s, let's use the nicely RNDIS_*-prefixed defines from the HyperV implementation, rename everywhere they're used, and copy+rename the few that were missing from this list of objects. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-12usb/net: rndis: inline the cpu_to_le32() macroLinus Walleij1-26/+28
The header file <linux/usb/rndis_host.h> used a number of #defines that included the cpu_to_le32() macro to assure the result will be in LE endianness. Inlining this into the code instead of using it in the code definitions yields consolidation opportunities later on as you will see in the following patches. The individual drivers also used local defines - all are switched over to the pattern of doing the conversion at the call sites instead. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-18USB: convert drivers/net/* to use module_usb_driver()Greg Kroah-Hartman1-11/+1
This converts the drivers in drivers/net/* to use the module_usb_driver() macro which makes the code smaller and a bit simpler. Added bonus is that it removes some unneeded kernel log messages about drivers loading and/or unloading. Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Samuel Ortiz <samuel@sortiz.org> Cc: Oliver Neukum <oliver@neukum.name> Cc: Peter Korsgaard <jacmet@sunsite.dk> Cc: Petko Manolov <petkan@users.sourceforge.net> Cc: Steve Glendinning <steve.glendinning@smsc.com> Cc: Christian Lamparter <chunkeey@googlemail.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Dan Williams <dcbw@redhat.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Cc: Herton Ronaldo Krzesinski <herton@canonical.com> Cc: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Chaoming Li <chaoming_li@realsil.com.cn> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: "David S. Miller" <davem@davemloft.net> Cc: Roel Kluin <roel.kluin@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: Pavel Roskin <proski@gnu.org> Cc: Yoann DI-RUZZA <y.diruzza@lim.eu> Cc: George <george0505@realtek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-15rndis_host: Quirky devices are still 'point-to-point'Ben Hutchings1-1/+1
My changes in commit 4d42d417be75d750b82798922b6e775915e11bce were written some time before the introduction of FLAG_POINTTOPOINT, so didn't include that flag in the new driver_info. Change the new driver_info to be consistent. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-14rndis_host: Poll status before control channel where necessaryBen Hutchings1-7/+32
Some RNDIS devices don't respond on the control channel until polled on the status channel. In particular, this was reported to be the case for the 2Wire HomePortal 1000SW and for some Windows Mobile devices. This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk> which is currently applied by Mandriva. Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-02usbnet: use eth%d name for known ethernet devicesArnd Bergmann1-1/+1
The documentation for the USB ethernet devices suggests that only some devices are supposed to use usb0 as the network interface name instead of eth0. The logic used there, and documented in Kconfig for CDC is that eth0 will be used when the mac address is a globally assigned one, but usb0 is used for the locally managed range that is typically used on point-to-point links. Unfortunately, this has caused a lot of pain on the smsc95xx device that is used on the popular pandaboard without an EEPROM to store the MAC address, which causes the driver to call random_ether_address(). Obviously, there should be a proper MAC addressed assigned to the device, and discussions are ongoing about how to solve this, but this patch at least makes sure that the default interface naming gets a little saner and matches what the user can expect based on the documentation, including for new devices. The approach taken here is to flag whether a device might be a point-to-point link with the new FLAG_POINTTOPOINT setting in the usbnet driver_info. A driver can set both FLAG_POINTTOPOINT and FLAG_ETHER if it is not sure (e.g. cdc_ether), or just one of the two. The usbnet framework only looks at the MAC address for device naming if both flags are set, otherwise it trusts the flag. Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org> Tested-by: Andy Green <andy.green@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-03net: Revert "rndis_host: Poll status channel before control channel"Ben Hutchings1-12/+6
This reverts commit c17b274dc2aa538b68c1f02b01a3c4e124b435ba. That change was reported to break rndis_wlan support for the WUSB54GS. Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-16rndis_host: Poll status channel before control channelBen Hutchings1-6/+12
Some RNDIS devices don't respond on the control channel until polled on the status channel. In particular, this was reported to be the case for the 2Wire HomePortal 1000SW. This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk> which is reported to be needed for use with some Windows Mobile devices and which is currently applied by Mandriva. Reported-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Mark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo1-0/+1
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-02-18drivers/net/usb: Use netif_<level> logging facilitiesJoe Perches1-8/+6
Convert from: if (netif_msg_<foo>(priv)) dev_<level>(dev... to netif_<level>(priv, foo, dev... Also convert a few: if (i < REG_TIMEOUT) { etc... return ret; } to if (i >= REG_TIMEOUT) goto fail; etc... return ret; Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-18usbnet: Convert dev(dbg|err|warn|info) macros to netdev_<level>Joe Perches1-5/+5
These macros are too similar to the dev_<level> equivalents but take a usbnet * argument. Convert them to the recently introduced netdev_<level> macros and remove the old macros. The old macros had "\n" appended to the format string. Add the "\n" to the converted uses. Some existing uses of the dev<foo> macros in cdc_eem.c probably mistakenly had trailing "\n". No "\n" added there. Fix net1080 this/other log message inversion. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-04drivers/net: Move && and || to end of previous lineJoe Perches1-5/+5
Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-31USB: rndis_host: debug info clobbered before it is loggedGeorge Nassar1-3/+3
The MTU throttle-down if a RNDIS device doesn't support a particular packet size is being incorrectly logged. The attempted packet size is being clobbered before it gets logged. First patch; please inform if I'm doing this incorrectly. Diff'd against latest official source as per the FAQ; forward port to current git version is straightforward. Signed-off-by: George Nassar <george.nassar@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-07rndis_host: support ETHTOOL_GPERMADDRJohn W. Linville1-0/+1
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-05rndis_host: allow rndis_wlan to see all indicationsJussi Kivilinna1-21/+29
Allow rndis_wlan to see all indications. Currently rndis_host lets rndis_wlan to know about link state changes only, but there is whole set of other 802.11-specific indications that rndis_wlan should handle properly. So rename link_change() to indication() and convert rndis_wlan to use it. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-07-01rndis_host: Use netdev stats structureHerbert Xu1-1/+1
Now that netdev has its own stats structure we should use that instead. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22usbnet: convert rndis driver to net_device_opsStephen Hemminger1-1/+12
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15rndis: remove private wrapper of __constant_cpu_to_le32Harvey Harrison1-14/+11
Use cpu_to_le32 directly as it handles constant folding now, replace direct uses of __constant_cpu_to_{endian} as well. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-23rndis_host: support WM6 devices as modemsThomas Backlund1-0/+4
This patch allows Windows Mobile 6 devices to be used for tethering -- that is, used as modems. It was requested by AdamW in kernel bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=11119 and Mandriva kernel-discuss list. It is tested and confirmed to work by Peterl: http://forum.eeeuser.com/viewtopic.php?pid=323543#p323543 This patch is based on the patch in the above kernel bugzilla, which is from the usb-rndis-lite tree. [ dbrownell@users.sourceforge.net: misc fixes ] Signed-off-by: Thomas Backlund <tmb@mandriva.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-28rndis_host: pass buffer length to rndis_commandJussi Kivilinna1-7/+7
Pass buffer length to rndis_command so that rndis_command can read full response buffer from device instead of max CONTROL_BUFFER_SIZE bytes. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-29Merge branch 'upstream-next-davem' of ↵David S. Miller1-2/+2
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
2008-05-22misc drivers/net endianness noiseAl Viro1-2/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-22rndis_host: increase delay in command response loopPierre Ynard1-1/+1
Some devices running some WinCE firmware (with SC_* Samsung processors according to the SynCE project, verified on a HTC P3600 device) fail to register because they apparently need extra time to respond correctly to requests. Increase the existing delay to satisfy them. Based on code from the SynCE project, on a suggestion of David Brownell. This patch Works For Me(tm). Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr> Acked-by: David Brownell <david-b@pacbell.net> Cc: Greg KH <greg@kroah.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-03-28Merge branch 'master' of ↵David S. Miller1-3/+6
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/usb/rndis_host.c drivers/net/wireless/b43/dma.c net/ipv6/ndisc.c
2008-03-26endianness annotations: rndisAl Viro1-1/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-26misc drivers/net annotationsAl Viro1-1/+1
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-26rndis_host: fix oops when query for OID_GEN_PHYSICAL_MEDIUM failsJussi Kivilinna1-3/+6
When query for OID_GEN_PHYSICAL_MEDIUM fails, uninitialized pointer 'phym' is being accessed in generic_rndis_bind(), resulting OOPS. Patch fixes phym to be initialized and setup correctly when rndis_query() for physical medium fails. Bug was introduced by following commit: commit 039ee17d1baabaa21783a0d5ab3e8c6d8c794bdf Author: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Date: Sun Jan 27 23:34:33 2008 +0200 Reported-by: Dmitri Monakhov <dmonakhov@openvz.org> Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-17rndis_host: fix transfer size negotiationJean-Christophe Dubois1-4/+8
This patch should resolve a problem that's troubled support for some RNDIS peripherals. It seems to have boiled down to using a variable to establish transfer size limits before it was assigned, which caused those devices to fallback to a default "jumbogram" mode we don't support. Fix by assigning it earlier for RNDIS. Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net> [ cleanups ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-01Move usbnet.h and rndis_host.h to include/linux/usbJussi Kivilinna1-3/+2
Move headers usbnet.h and rndis_host.h to include/linux/usb and fix includes for drivers/net/usb modules. Headers are moved because rndis_wlan will be outside drivers/net/usb in drivers/net/wireless and yet need these headers. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()Jussi Kivilinna1-3/+33
Add RNDIS physical medium checking into generic_rndis_bind() and also make rndis_host to be only bind on every medium except wireless. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Add link_change function pointer to 'struct rndis_data'.Jussi Kivilinna1-4/+20
Callback to signal link state changes from minidriver to 'subminidrivers'. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Add early_init function pointer to 'struct rndis_data'.Jussi Kivilinna1-0/+6
Function pointer is for 'subminidrivers' that need to do work on device right after minidriver has initialized hardware. For example, rndis_wlan setting device specific configuration parameters with OID_GEN_RNDIS_CONFIG_PARAMETER right after rndis_host has initialized hardware with RNDIS_INIT. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: export functionsJussi Kivilinna1-7/+13
Export rndis_host functions and also rename rndis_bind() to generic_rndis_bind() for modules using rndis_host as base. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Split up rndis_host.cJussi Kivilinna1-222/+1
Split up rndis_host.c into rndis_host.h and rndis_base.c. This is done so that rndis_wlan can reuse common parts with rndis_host. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Fix rndis packet filter flags.Jussi Kivilinna1-1/+22
RNDIS packet filter flags are not exactly the same as CDC flags so we cannot reuse them. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Bjorge Dijkstra <bjd@jooz.net> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Halt device if rndis_bind fails.Jussi Kivilinna1-3/+9
When bind fails after device was initialized, shutdown device properly by sending RNDIS_MSG_HALT. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Bjorge Dijkstra <bjd@jooz.net> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-01rndis_host: Use 1KB buffer in rndis_unbindJussi Kivilinna1-1/+1
rndis_command requires the caller to pass in a buffer of at least 1KB. Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: Bjorge Dijkstra <bjd@jooz.net> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-12-01 06:49:39 +0300