summaryrefslogtreecommitdiff
path: root/drivers/net/sfc
AgeCommit message (Collapse)AuthorFilesLines
2009-03-22sfc: Implement adaptive IRQ moderationBen Hutchings6-21/+73
Calculate a score for each 1000 IRQs: - TX completions are worth 1 point - RX completions are worth 4 if merged using LRO or 2 otherwise Reduce moderation if the score is less than 10000, down to a minimum of 5 us. Increase moderation if the score is more than 20000, up to the specified maximum. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22sfc: Optimise falcon_writel_page_locked() for page > 0Ben Hutchings1-5/+8
The bug this function works around only applies to the first set of page-mapped registers; other pages can be written without locking. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22sfc: Remove unused private PCI register definitionsBen Hutchings1-7/+0
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22sfc: Work around unreliable legacy interrupt statusBen Hutchings1-12/+14
In rare cases, reading the legacy interrupt status register can acknowledge an event queue whose attention flag has not yet been set in the register. Until we service this event queue it will not generate any more interrupts. Therefore, as a secondary check, poll the next slot in each active event queue whose flag is not set. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22sfc: Pad packets to 33 bytes to prevent TX packet parser lockupBen Hutchings2-0/+10
The packet parser used in the TX data path for locating checksum fields can lose synchronisation with the TX queue manager when handling packets that look like IPv4 but are too short (17-32 bytes). Work around this by padding to 33 bytes. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Improve NIC internal error recoveryBen Hutchings1-4/+19
Make the error count a per-NIC variable. Reset this the count after an hour if it has not reached the critical value. Set the critical value back to 5. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Fix search for flush completion eventsBen Hutchings1-12/+9
When flushing queues we disable normal interrupt and event handling and poll event queue 0 looking for flush completions. Unfortunately the flush event polling loop fails to move past any other type of event. This problem has not been observed in production hardware but appears to be a possibility. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Don't wake TX queues while they're being flushedBen Hutchings1-1/+1
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Clear I2C adapter structure in falcon_remove_nic()Ben Hutchings1-0/+2
i2c_del_adapter() leaves dangling pointers in the structure. If we retry the NIC probe and pass the structure to i2c_add_adapter() again it will lead to an oops unless we clear it first. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Clean up properly on reset failure pathsBen Hutchings1-3/+6
If MAC switching fails, stop the port properly. If PHY reinitialisation fails, clear the port_initialized flag. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Reject packets from the kernel TX queue during a loopback self-testBen Hutchings1-0/+3
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-05sfc: Fix efx_ethtool_nway_result() to use clause 45 MDIO registersBen Hutchings1-1/+8
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Add support for SFN4112F SFP+ reference designBen Hutchings2-0/+63
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Clean up LED controlBen Hutchings3-12/+11
Reinitialise LEDs after overriding them for identification. Rename set_fault_led method to set_id_led since we always use it for NIC identification and not faults. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Delete unused efx_blinker::led_num fieldBen Hutchings2-3/+0
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Add support for QT2025C PHYBen Hutchings4-10/+91
This is a new PHY supporting SFP+ modules, used in the SFN4112F reference design. It is similar to the QT2022C2 and shares much of its support code. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Fix reporting of PHY idBen Hutchings3-7/+22
Shuffle bits of the OUI into the conventional written order. Replace PHY id component macros with functions. Zero-pad PHY id components in log messages. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Remove "XFP" from log messages that are not specific to XFPBen Hutchings1-4/+4
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisationBen Hutchings3-40/+72
During SFN4111T initialisation, check whether the PHY boot status indicates a bad firmware checksum. If so, prepare to reflash rather than continuing with normal initialisation. Remove redundant PHY boot status check from tenxpress_phy_init(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: Fix test for MDIO read failureBen Hutchings1-6/+7
Commit 27dd2caca4eabe7c13a052b7456495ba75535e6a changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02sfc: SFT9001: Include non-breaking cable diagnostics in online self-testsBen Hutchings1-21/+24
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-19drivers/net/sfc: fix sparse warnings: Should it be static?Hannes Eder1-0/+1
Impact: Include the header file. If CONFIG_SFC_MTD is not defined then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined 'static inline' with an empty function body in the header file, but the the whole file mtd.c is not built in this case. Fix this sparse warnings: drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static? drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static? drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-18drivers/net/sfc: fix sparse warning: symbol shadows an earlier oneHannes Eder1-4/+3
Impact: Move variable declaration as close to their usage as possible. Fix this sparse warning: drivers/net/sfc/tenxpress.c:589:22: warning: symbol 'link_ok' shadows an earlier one drivers/net/sfc/tenxpress.c:575:30: originally declared here Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01net: replace uses of __constant_{endian}Harvey Harrison1-2/+2
Base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31Merge branch 'master' of ↵David S. Miller12-302/+279
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000/e1000_main.c
2009-01-31sfc: Replace stats_enabled flag with a disable countBen Hutchings6-25/+57
Currently we use a spin-lock to serialise statistics fetches and also to inhibit them for short periods of time, plus a flag to enable/disable statistics fetches for longer periods of time, during online reset. This was apparently insufficient to deal with the several reasons for stats being disabled. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFX7101/SFT9001: Fix AN advertisementsBen Hutchings6-201/+141
All 10Xpress PHYs require autonegotiation all the time; enforce this in the set_settings() method and do not treat it as a workaround. Remove claimed support for 100M HD mode since it is not supported by current firmware. Do not set speed override bits when AN is enabled, and do not use register 1.49192 for AN configuration as it can override what we set elsewhere. Always set the AN selector bits to 1 (802.3). Fix confusion between Next Page and Extended Next Page. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFT9001: Always enable XNP exchange on SFT9001 rev BBen Hutchings1-1/+1
This workaround is not specific to rev A. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: Update board info for hardware monitor on SFN4111T-R5 and laterBen Hutchings1-2/+10
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: Test for PHYXS faults whenever we cannot test link state bitsSteve Hodgson1-7/+9
Depending on the loopback mode, there may be no pertinent link state bits. In this case we test the PHYXS RX fault bit instead. Make sure to do this in all cases where there are no link state bits. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: Reinitialise the PHY completely in case of a PHY or NIC resetSteve Hodgson4-13/+28
In particular, set pause advertising bits properly. A PHY reset is not necessary to recover from the register self-test, so use a "invisible" reset there instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: Fix post-reset MAC selectionSteve Hodgson1-7/+8
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the MAC is the same as it was before. This ensures that the value is correct after an online reset. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1Ben Hutchings1-6/+9
Change sfn4111t_reset() to change only GPIO output enables so that it doesn't break subsequent I2C operations. Update comments to explain exactly what we're doing. Add a short sleep to make sure the FLASH_CFG_1 value is latched before any subsequent I2C operations. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFT9001: Fix speed reporting in 1G PHY loopbackSteve Hodgson3-18/+18
Instead of disabling AN in loopback, just prevent restarting AN and override the speed in sft9001_get_settings(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFX7101: Remove workaround for bad link trainingSteve Hodgson4-28/+0
Early versions of the SFX7101 firmware could complete link training in a state where it would not adequately cancel noise (Solarflare bug 10750). We previously worked around this by resetting the PHY after seeing many Ethernet CRC errors. This workaround is unsafe since it takes no account of the interval between errors; it also appears to be unnecessary with production firmware. Therefore remove it. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-31sfc: SFT9001: Enable robust link trainingSteve Hodgson1-1/+5
Enable a firmware option that appears to be necessary for reliable operation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-28net: Add skb_record_rx_queue() calls to multiqueue capable drivers.David S. Miller1-0/+2
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22sfc: Replace LRO with GROHerbert Xu7-214/+19
This patch makes sfc invoke the GRO hooks instead of LRO. As GRO has a compatible external interface to LRO this is a very straightforward replacement. Everything should appear identical to the user except that the offload is now controlled by the GRO ethtool option instead of LRO. I've kept the lro module parameter as is since that's for compatibility only. I have eliminated efx_rx_mk_skb as the GRO layer can take care of all packets regardless of whether GRO is enabled or not. So the only case where we don't call GRO is if the packet checksum is absent. This is to keep the behaviour changes of the patch to a minimum. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-22net: Remove redundant NAPI functionsBen Hutchings2-3/+3
Following the removal of the unused struct net_device * parameter from the NAPI functions named *netif_rx_* in commit 908a7a1, they are exactly equivalent to the corresponding *napi_* functions and are therefore redundant. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-11sfc: SFT9001: Fix condition for LNPGA power-offBen Hutchings1-2/+3
Only the SFX7101 requires software power control. This was incorrectly being applied to the SFT9001 rev A as well. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-07net: sfc: Use pci_clear_master() to disable bus masteringBen Hutchings1-2/+2
pci_disable_device() disables many features, like MSI-X, which we never reenable in efx_reset(). Further, calls to pci_enable_device() and pci_disable_device() must be matched since the nesting count was introduced, so switch to using pci_clear_master() instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2008-12-27net: Fix warning fallout from recent NAPI interface changes.David S. Miller1-1/+0
When we removed the network device argument from several NAPI interfaces in 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused netdev arg from some NAPI interfaces.") several drivers now started getting unused variable warnings. This fixes those up. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings1-7/+10
When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings1-24/+23
This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: SFT9001: Add cable diagnosticsBen Hutchings1-8/+107
The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Add support for multiple PHY self-testsBen Hutchings5-15/+44
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Merge top-level functions for self-testsBen Hutchings3-55/+48
Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Clean up PHY mode management in loopback self-testBen Hutchings1-12/+7
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Fix unreliable link detection in some loopback modesBen Hutchings3-13/+24
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-27sfc: Generate unique names for per-NIC workqueuesBen Hutchings2-1/+6
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-17 01:49:07 +0300