summaryrefslogtreecommitdiff
path: root/drivers/net/phy
AgeCommit message (Collapse)AuthorFilesLines
2020-05-07ethtool: provide UAPI for PHY master/slave configuration.Oleksij Rempel2-1/+97
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of auto-negotiation support, we needed to be able to configure the MASTER-SLAVE role of the port manually or from an application in user space. The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to force MASTER or SLAVE role. See IEEE 802.3-2018: 22.2.4.3.7 MASTER-SLAVE control register (Register 9) 22.2.4.3.8 MASTER-SLAVE status register (Register 10) 40.5.2 MASTER-SLAVE configuration resolution 45.2.1.185.1 MASTER-SLAVE config value (1.2100.14) 45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32) The MASTER-SLAVE role affects the clock configuration: ------------------------------------------------------------------------------- When the PHY is configured as MASTER, the PMA Transmit function shall source TX_TCLK from a local clock source. When configured as SLAVE, the PMA Transmit function shall source TX_TCLK from the clock recovered from data stream provided by MASTER. iMX6Q KSZ9031 XXX ------\ /-----------\ /------------\ | | | | | MAC |<----RGMII----->| PHY Slave |<------>| PHY Master | |<--- 125 MHz ---+-<------/ | | \ | ------/ \-----------/ \------------/ ^ \-TX_TCLK ------------------------------------------------------------------------------- Since some clock or link related issues are only reproducible in a specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial to provide generic (not 100BASE-T1 specific) interface to the user space for configuration flexibility and trouble shooting. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-07net: phy: mscc: use phy_package_sharedMichael Walle2-70/+32
Use the new phy_package_shared common storage to ease the package initialization and to access the global registers. Signed-off-by: Michael Walle <michael@walle.cc> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-07net: phy: bcm54140: use phy_package_sharedMichael Walle1-46/+11
Use the new phy_package_shared common storage to ease the package initialization and to access the global registers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-07net: phy: add concept of shared storage for PHYsMichael Walle2-0/+139
There are packages which contain multiple PHY devices, eg. a quad PHY transceiver. Provide functions to allocate and free shared storage. Usually, a quad PHY contains global registers, which don't belong to any PHY. Provide convenience functions to access these registers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-02net: phy: DP83TC811: Fix WoL in config init to be disabledDan Murphy1-9/+12
The WoL feature should be disabled when config_init is called and the feature should turned on or off when set_wol is called. In addition updated the calls to modify the registers to use the set_bit and clear_bit function calls. Fixes: 6d749428788b ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy") Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-02net: phy: DP83822: Fix WoL in config init to be disabledDan Murphy1-16/+14
The WoL feature should be disabled when config_init is called and the feature should turned on or off when set_wol is called. In addition updated the calls to modify the registers to use the set_bit and clear_bit function calls. Fixes: 3b427751a9d0 ("net: phy: DP83822 initial driver submission") Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01net: phy: bcm54140: add second PHY IDMichael Walle1-2/+9
This PHY has two PHY IDs depending on its mode. Adjust the mask so that it includes both IDs. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01net: phy: bcm54140: apply the workaround on b0 chipsMichael Walle1-3/+8
The lower three bits of the phy_id specifies the chip stepping. The workaround is specifically for the B0 stepping. Apply it only on these chips. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01net: phy: bcm54140: fix phy_id_maskMichael Walle1-2/+2
Broadcom defines the bits for this PHY as follows: { oui[24:3], model[6:0], revision[2:0] } Thus we have to mask the lower three bits only. Fixes: 6937602ed3f9 ("net: phy: add Broadcom BCM54140 support") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01net: phy: bcm54140: use genphy_soft_reset()Michael Walle1-0/+1
Set the .soft_reset() op to be sure there will be a reset even if there is no hardware reset line registered. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01net: phy: at803x: add downshift supportMichael Walle1-0/+87
The AR8031 and AR8035 support the link speed downshift. Add driver support for it. One peculiarity of these PHYs is that it needs a software reset after changing the setting, thus add the .soft_reset() op and do a phy_init_hw() if necessary. This was tested on a custom board with the AR8031. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-01dp83640: reverse arguments to list_add_tailJulia Lawall1-1/+1
In this code, it appears that phyter_clocks is a list head, based on the previous list_for_each, and that clock->list is intended to be a list element, given that it has just been initialized in dp83640_clock_init. Accordingly, switch the arguments to list_add_tail, which takes the list head as the second argument. Fixes: cb646e2b02b27 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-30net: phy: mdio: add IPQ4019 MDIO driverRobert Marko3-0/+168
This patch adds the driver for the MDIO interface inside of Qualcomm IPQ40xx series SoC-s. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-28net: phy: bcm54140: Make a bunch of functions staticChenTao1-3/+3
Fix the following warning: drivers/net/phy/bcm54140.c:663:5: warning: symbol 'bcm54140_did_interrupt' was not declared. Should it be static? drivers/net/phy/bcm54140.c:672:5: warning: symbol 'bcm54140_ack_intr' was not declared. Should it be static? drivers/net/phy/bcm54140.c:684:5: warning: symbol 'bcm54140_config_intr' was not declared. Should it be static? Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: ChenTao <chentao107@huawei.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-27net: phy: marvell10g: fix temperature sensor on 2110Baruch Siach1-1/+26
Read the temperature sensor register from the correct location for the 88E2110 PHY. There is no enable/disable bit on 2110, so make mv3310_hwmon_config() run on 88X3310 only. Fixes: 62d01535474b61 ("net: phy: marvell10g: add support for the 88x2110 PHY") Cc: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-26net: phy: dp83867: Remove unneeded semicolonZheng Bin1-2/+2
Fixes coccicheck warning: drivers/net/phy/dp83867.c:368:2-3: Unneeded semicolon drivers/net/phy/dp83867.c:403:2-3: Unneeded semicolon Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zheng Bin <zhengbin13@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller3-4/+176
Simple overlapping changes to linux/vermagic.h Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-25net: phy: clear phydev->suspended after soft resetHeiner Kallweit1-1/+11
If a soft reset is triggered whilst PHY is in power-down, then phydev->suspended will remain set. Seems we didn't face any issue yet caused by this, but better reset the suspended flag after soft reset. See also the following from 22.2.4.1.1 Resetting a PHY is accomplished by setting bit 0.15 to a logic one. This action shall set the status and control registers to their default states. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-25net: phy: remove genphy_no_soft_resetHeiner Kallweit5-6/+0
Since 6e2d85ec0559 ("net: phy: Stop with excessive soft reset") we don't need genphy_no_soft_reset() any longer. Not setting callback soft_reset results in a no-op now. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-25net: phy: make phy_suspend a no-op if PHY is suspended alreadyHeiner Kallweit1-0/+3
Gently handle the case that phy_suspend() is called whilst PHY is in power-down. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-25net: phylink, dsa: eliminate phylink_fixed_state_cb()Russell King1-31/+15
Move the callback into the phylink_config structure, rather than providing a callback to set this up. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-24net: phy: bcm54140: fix less than zero comparison on an unsignedColin Ian King1-2/+4
Currently the unsigned variable tmp is being checked for an negative error return from the call to bcm_phy_read_rdb and this can never be true since tmp is unsigned. Fix this by making tmp a plain int. Addresses-Coverity: ("Unsigned compared against 0") Fixes: 4406d36dfdf1 ("net: phy: bcm54140: add hwmon support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-24net: phy: bcm84881: clear settings on link downRussell King1-3/+3
Clear the link partner advertisement, speed, duplex and pause when the link goes down, as other phylib drivers do. This avoids the stale link partner, speed and duplex settings being reported via ethtool. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-23net: phy: marvell10g: limit soft reset to 88x3310Baruch Siach1-1/+2
The MV_V2_PORT_CTRL_SWRST bit in MV_V2_PORT_CTRL is reserved on 88E2110. Setting SWRST on 88E2110 breaks packets transfer after interface down/up cycle. Fixes: 8f48c2ac85ed ("net: marvell10g: soft-reset the PHY when coming out of low power") Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-23net: phy: tja11xx: add delayed registration of TJA1102 PHY1Oleksij Rempel1-7/+105
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1 having no ID. On one hand it is possible to for PHY detection by compatible, on other hand we should be able to reset complete chip before PHY1 configured it, and we need to define dependencies for proper power management. We can solve it by defining PHY1 as child of PHY0: tja1102_phy0: ethernet-phy@4 { reg = <0x4>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; reset-assert-us = <20>; reset-deassert-us = <2000>; tja1102_phy1: ethernet-phy@5 { reg = <0x5>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; }; }; The PHY1 should be a subnode of PHY0 and registered only after PHY0 was completely reset and initialized. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-23net: phy: tja11xx: add initial TJA1102 supportOleksij Rempel1-0/+91
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable. Both PHYs are similar but have different amount of functionality. For example PHY 1 has no PHY ID and no health monitor. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-23net: phy: Use IS_ERR() to check and simplify codeTang Bin1-5/+2
Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO() to simplify code, avoid redundant paramenter definitions and judgements. Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-23net: phy: micrel: add phy-mode support for the KSZ9031 PHYOleksij Rempel1-5/+123
Add support for following phy-modes: rgmii, rgmii-id, rgmii-txid, rgmii-rxid. This PHY has an internal RX delay of 1.2ns and no delay for TX. The pad skew registers allow to set the total TX delay to max 1.38ns and the total RX delay to max of 2.58ns (configurable 1.38ns + build in 1.2ns) and a minimal delay of 0ns. According to the RGMII v1.3 specification the delay provided by PCB traces should be between 1.5ns and 2.0ns. The RGMII v2.0 allows to provide this delay by MAC or PHY. So, we configure this PHY to the best values we can get by this HW: TX delay to 1.38ns (max supported value) and RX delay to 1.80ns (best calculated delay) The phy-modes can still be fine tuned/overwritten by *-skew-ps device tree properties described in: Documentation/devicetree/bindings/net/micrel-ksz90x1.txt Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: add device-managed devm_mdiobus_registerHeiner Kallweit1-1/+7
If there's no special ordering requirement for mdiobus_unregister(), then driver code can be simplified by using a device-managed version of mdiobus_register(). Prerequisite is that bus allocation has been done device-managed too. Else mdiobus_free() may be called whilst bus is still registered, resulting in a BUG_ON(). Therefore let devm_mdiobus_register() return -EPERM if bus was allocated non-managed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: bcm54140: add hwmon supportMichael Walle2-0/+397
The PHY supports monitoring its die temperature as well as two analog voltages. Add support for it. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: add Broadcom BCM54140 supportMichael Walle3-0/+492
The Broadcom BCM54140 is a Quad SGMII/QSGMII Copper/Fiber Gigabit Ethernet transceiver. This also adds support for tunables to set and get downshift and energy detect auto power-down. The PHY has four ports and each port has its own PHY address. There are per-port registers as well as global registers. Unfortunately, the global registers can only be accessed by reading and writing from/to the PHY address of the first port. Further, there is no way to find out what port you actually are by just reading the per-port registers. We therefore, have to scan the bus on the PHY probe to determine the port and thus what address we need to access the global registers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: broadcom: add helper to write/read RDB registersMichael Walle2-0/+89
RDB (Register Data Base) registers are used on newer Broadcom PHYs. Add helper to read, write and modify these registers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: microchip_t1: add lan87xx_phy_init to initialize the lan87xx phy.Yuiko Oshino1-0/+171
lan87xx_phy_init() initializes the lan87xx phy hardware including its TC10 Wake-up and Sleep features. Fixes: 3e50d2da5850 ("Add driver for Microchip LAN87XX T1 PHYs") Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> v0->v1: - Add more details in the commit message and source comments. - Update to the latest initialization sequences. - Add access_ereg_modify_changed(). - Fix access_ereg() to access SMI bank correctly. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-21Update rmk's email address in various driversRussell King1-1/+1
Globally update my email address in six files scattered through the tree. Acked-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2020-04-20net: phy: mscc: use mdiobus_get_phy()Michael Walle1-4/+3
Don't use internal knowledge of the mdio bus core, instead use mdiobus_get_phy() which does the same thing. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net: phy: Propagate error from bus->resetFlorian Fainelli1-3/+6
If a bus->reset() call for the mii_bus structure returns an error (e.g.: -EPROE_DEFER) we should propagate it accordingly. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net: phy: realtek: add delay to resume path of certain internal PHY'sHeiner Kallweit1-2/+13
Internal PHY's from RTL8168h up may not be instantly ready after calling genphy_resume(). So far r8169 network driver adds the needed delay, but better handle this in the PHY driver. The network driver may miss other places where the PHY is resumed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-19net: phy: broadcom: Add support for BCM53125 internal PHYsFlorian Fainelli1-0/+14
BCM53125 has internal Gigabit PHYs which support interrupts as well as statistics, make it possible to configure both of those features with a PHY driver entry. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-19net: phy: mdio-bcm-iproc: Do not show kernel pointerFlorian Fainelli1-1/+1
Displaying the virtual address at which the MDIO base register address has been mapped is not useful and is not visible with pointer hashing in place, replace the message with something indicating successful registration instead. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-19net: phy: at803x: add support for AR8032 PHYDavid Bauer1-0/+17
This adds support for the Qualcomm Atheros AR8032 Fast Ethernet PHY. It shares many similarities with the already supported AR8030 PHY but additionally supports MII connection to the MAC. Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15net: marvell10g: soft-reset the PHY when coming out of low powerRussell King1-3/+13
Soft-reset the PHY when coming out of low power mode, which seems to be necessary with firmware versions 0.3.3.0 and 0.3.10.0. This depends on ("net: marvell10g: report firmware version") Fixes: c9cc1c815d36 ("net: phy: marvell10g: place in powersave mode at probe") Reported-by: Matteo Croce <mcroce@redhat.com> Tested-by: Matteo Croce <mcroce@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15net: marvell10g: report firmware versionRussell King1-0/+20
Report the firmware version when probing the PHY to allow issues attributable to firmware to be diagnosed. Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-15net: phy: micrel: use genphy_read_status for KSZ9131Atsushi Nemoto1-1/+1
KSZ9131 will not work with some switches due to workaround for KSZ9031 introduced in commit d2fd719bcb0e83cb39cfee22ee800f98a56eceb3 ("net/phy: micrel: Add workaround for bad autoneg"). Use genphy_read_status instead of dedicated ksz9031_read_status. Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-12net: phy: marvell: Fix pause frame negotiationClemens Gruber1-22/+24
The negotiation of flow control / pause frame modes was broken since commit fcf1f59afc67 ("net: phy: marvell: rearrange to use genphy_read_lpa()") moved the setting of phydev->duplex below the phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that function, phydev->pause was no longer set. Fix it by moving the parsing of the status variable before the blocks dealing with the pause frames. As the Marvell 88E1510 datasheet does not specify the timing between the link status and the "Speed and Duplex Resolved" bit, we have to force the link down as long as the resolved bit is not set, to avoid reporting link up before we even have valid Speed/Duplex. Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T) Fixes: fcf1f59afc67 ("net: phy: marvell: rearrange to use genphy_read_lpa()") Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-04-08Documentation: mdio_bus.c - fix warningsLothar Rubusch1-1/+1
Fix wrong parameter description and related warnings at 'make htmldocs'. Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-04net: phy: micrel: kszphy_resume(): add delay after genphy_resume() before ↵Oleksij Rempel1-0/+7
accessing PHY registers After the power-down bit is cleared, the chip internally triggers a global reset. According to the KSZ9031 documentation, we have to wait at least 1ms for the reset to finish. If the chip is accessed during reset, read will return 0xffff, while write will be ignored. Depending on the system performance and MDIO bus speed, we may or may not run in to this issue. This bug was discovered on an iMX6QP system with KSZ9031 PHY and attached PHY interrupt line. If IRQ was used, the link status update was lost. In polling mode, the link status update was always correct. The investigation showed, that during a read-modify-write access, the read returned 0xffff (while the chip was still in reset) and corresponding write hit the chip _after_ reset and triggered (due to the 0xffff) another reset in an undocumented bit (register 0x1f, bit 1), resulting in the next write being lost due to the new reset cycle. This patch fixes the issue by adding a 1...2 ms sleep after the genphy_resume(). Fixes: 836384d2501d ("net: phy: micrel: Add specific suspend") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-01net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035Oleksij Rempel1-2/+2
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set for the values that comprise the fields, not zero-bits-set. This patch fixes the clock frequency configuration for ATH8030 and ATH8035 Atheros PHYs by removing the erroneous "~". To reproduce this bug, configure the PHY with the device tree binding "qca,clk-out-frequency" and remove the machine specific PHY fixups. Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reported-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk> Tested-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-30net: phylink: add separate pcs operations structureRussell King1-22/+55
Add a separate set of PCS operations, which MAC drivers can use to couple phylink with their associated MAC PCS layer. The PCS operations include: - pcs_get_state() - reads the link up/down, resolved speed, duplex and pause from the PCS. - pcs_config() - configures the PCS for the specified mode, PHY interface type, and setting the advertisement. - pcs_an_restart() - restarts 802.3 in-band negotiation with the link partner - pcs_link_up() - informs the PCS that link has come up, and the parameters of the link. Link parameters are used to program the PCS for fixed speed and non-inband modes. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-30net: phylink: rename 'ops' to 'mac_ops'Russell King1-15/+15
Rename the bland 'ops' member of struct phylink to be a more descriptive 'mac_ops' - this is necessary as we're about to introduce another set of operations. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-30net: phylink: change phylink_mii_c22_pcs_set_advertisement() prototypeRussell King1-5/+7
Change phylink_mii_c22_pcs_set_advertisement() to take only the PHY interface and advertisement mask, rather than the full phylink state. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-29 11:05:36 +0300