| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit c52ecff7e6439ca8c9b03282e8869a005aa94831 ]
Old Mellanox silicons, like switchx-2, switch-ib do not support reading
QSFP modules temperature through MTMP register. Attempt to access this
register on systems equipped with the this kind of silicon will cause
initialization flow failure.
Test for hardware resource capability is added in order to distinct
between old and new silicon - old silicons do not have such capability.
Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Fixes: 5c42eaa07bd0 ("mlxsw: core: Extend hwmon interface with QSFP module temperature attributes")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cb07d915bf278a7a3938b983bbcb4921366b5eff ]
Add rcu locks when accessing netdev when processing route request
and tunnel keep alive messages received from hardware.
Fixes: 8e6a9046b66a ("nfp: flower vxlan neighbour offload")
Fixes: 856f5b135758 ("nfp: flower vxlan neighbour keep-alive")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 00f9fec48157f3734e52130a119846e67a12314b ]
The error print within mlx4_flow_steer_promisc_add() should
be a info print.
Fixes: 592e49dda812 ('net/mlx4: Implement promiscuous mode with device managed flow-steering')
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is the 5.1.3 stable release
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
[ Upstream commit ee0df19305d9fabd9479b785918966f6e25b733b ]
When changing the number of buffers in the RX ring while the interface
is running, the following Oops is encountered due to the new number
of buffers being taken into account immediately while their allocation
is done when opening the device only.
[ 69.882706] Unable to handle kernel paging request for data at address 0xf0000100
[ 69.890172] Faulting instruction address: 0xc033e164
[ 69.895122] Oops: Kernel access of bad area, sig: 11 [#1]
[ 69.900494] BE PREEMPT CMPCPRO
[ 69.907120] CPU: 0 PID: 0 Comm: swapper Not tainted 4.14.115-00006-g179ade8ce3-dirty #269
[ 69.915956] task: c0684310 task.stack: c06da000
[ 69.920470] NIP: c033e164 LR: c02e44d0 CTR: c02e41fc
[ 69.925504] REGS: dfff1e20 TRAP: 0300 Not tainted (4.14.115-00006-g179ade8ce3-dirty)
[ 69.934161] MSR: 00009032 <EE,ME,IR,DR,RI> CR: 22004428 XER: 20000000
[ 69.940869] DAR: f0000100 DSISR: 20000000
[ 69.940869] GPR00: c0352d70 dfff1ed0 c0684310 f00000a4 00000040 dfff1f68 00000000 0000001f
[ 69.940869] GPR08: df53f410 1cc00040 00000021 c0781640 42004424 100c82b6 f00000a4 df53f5b0
[ 69.940869] GPR16: df53f6c0 c05daf84 00000040 00000000 00000040 c0782be4 00000000 00000001
[ 69.940869] GPR24: 00000000 df53f400 000001b0 df53f410 df53f000 0000003f df708220 1cc00044
[ 69.978348] NIP [c033e164] skb_put+0x0/0x5c
[ 69.982528] LR [c02e44d0] ucc_geth_poll+0x2d4/0x3f8
[ 69.987384] Call Trace:
[ 69.989830] [dfff1ed0] [c02e4554] ucc_geth_poll+0x358/0x3f8 (unreliable)
[ 69.996522] [dfff1f20] [c0352d70] net_rx_action+0x248/0x30c
[ 70.002099] [dfff1f80] [c04e93e4] __do_softirq+0xfc/0x310
[ 70.007492] [dfff1fe0] [c0021124] irq_exit+0xd0/0xd4
[ 70.012458] [dfff1ff0] [c000e7e0] call_do_irq+0x24/0x3c
[ 70.017683] [c06dbe80] [c0006bac] do_IRQ+0x64/0xc4
[ 70.022474] [c06dbea0] [c001097c] ret_from_except+0x0/0x14
[ 70.027964] --- interrupt: 501 at rcu_idle_exit+0x84/0x90
[ 70.027964] LR = rcu_idle_exit+0x74/0x90
[ 70.037585] [c06dbf60] [20000000] 0x20000000 (unreliable)
[ 70.042984] [c06dbf80] [c004bb0c] do_idle+0xb4/0x11c
[ 70.047945] [c06dbfa0] [c004bd14] cpu_startup_entry+0x18/0x1c
[ 70.053682] [c06dbfb0] [c05fb034] start_kernel+0x370/0x384
[ 70.059153] [c06dbff0] [00003438] 0x3438
[ 70.063062] Instruction dump:
[ 70.066023] 38a00000 38800000 90010014 4bfff015 80010014 7c0803a6 3123ffff 7c691910
[ 70.073767] 38210010 4e800020 38600000 4e800020 <80e3005c> 80c30098 3107ffff 7d083910
[ 70.081690] ---[ end trace be7ccd9c1e1a9f12 ]---
This patch forbids the modification of the number of buffers in the
ring while the interface is running.
Fixes: ac421852b3a0 ("ucc_geth: add ethtool support")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5afcd14cfc7fed1bcc8abcee2cef82732772bfc2 ]
The old MIPS implementation of dma_cache_sync() didn't use the dev argument,
but commit c9eb6172c328 ("dma-mapping: turn dma_cache_sync into a
dma_map_ops method") changed that, so we now need to set dev.parent.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0504453139ef5a593c9587e1e851febee859c7d8 ]
Current order in open:
-> Enable interrupts (macb_init_hw)
-> Enable NAPI
-> Start PHY
Sequence of RX handling:
-> RX interrupt occurs
-> Interrupt is cleared and interrupt bits disabled in handler
-> NAPI is scheduled
-> In NAPI, RX budget is processed and RX interrupts are re-enabled
With the above, on QEMU or fixed link setups (where PHY state doesn't
matter), there's a chance macb RX interrupt occurs before NAPI is
enabled. This will result in NAPI being scheduled before it is enabled.
Fix this macb open by changing the order.
Fixes: ae1f2a56d273 ("net: macb: Added support for many RX queues")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d4c26eb6e721683a0f93e346ce55bc8dc3cbb175 ]
When adding more MAC addresses to a dwmac-sun8i interface, the device goes
directly in promiscuous mode.
This is due to IFF_UNICAST_FLT missing flag.
So since the hardware support unicast filtering, let's add IFF_UNICAST_FLT.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17170e6570c082717c142733d9a638bcd20551f8 ]
Fix issue with the entry indexing in the sg frame cleanup code being
off-by-1. This problem showed up when doing some basic iperf tests and
manifested in traffic coming to a halt.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes a compilation error caused by the phy_device "supported" and
"advertising" parameters switching from u32 to bitmap.
Fixes: 35998b5c4073 ("net: npcm: add NPCM7xx Ethernet MAC controller")
OpenBMC-Staging-Count: 2
Signed-off-by: Benjamin Fair <benjaminfair@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add Nuvoton BMC NPCM7xx Ethernet MAC controller (EMC) driver.
OpenBMC-Staging-Count: 3
Signed-off-by: Avi Fishman <avifishman70@gmail.com>
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_rx_pkt(), if the driver encounters BD errors, it will recycle
the buffers and jump to the end where the uninitailized variable "len"
is referenced. Fix it by adding a new jump label that will skip
the length update. This is the most correct fix since the length
may not be valid when we get this type of error.
Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In an earlier commit that fixes the number of stats contexts to
reserve for the RDMA driver, we added a function parameter to pass in
the number of stats contexts to all the relevant functions. The passed
in parameter should have been used to set the enables field of the
firmware message.
Fixes: 780baad44f0f ("bnxt_en: Reserve 1 stat_ctx for RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If driver determines that extended TX port statistics are not supported
or allocation of the data structure fails, make sure to pass 0 TX stats
size to firmware to disable it. The firmware returned TX stats size should
also be set to 0 for consistency. This will prevent
bnxt_get_ethtool_stats() from accessing the NULL TX stats pointer in
case there is mismatch between firmware and driver.
Fixes: 36e53349b60b ("bnxt_en: Add additional extended port statistics.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we encounter errors during open and proceed to clean up,
bnxt_hwrm_ring_free() may crash if the rings we try to free have never
been allocated. bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx()
may reference pointers that have not been allocated.
Fix it by checking for valid fw_ring_id first before calling
bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx().
Fixes: 2c61d2117ecb ("bnxt_en: Add helper functions to get firmware CP ring ID.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the bnxt_init_one() error path, short FW command request memory
is not freed. This patch fixes it.
Fixes: e605db801bde ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver builds a list of multicast addresses and sends it to the
firmware when the driver's ndo_set_rx_mode() is called. In rare
cases, the firmware can fail this call if internal resources to
add multicast addresses are exhausted. In that case, we should
try the call again by setting the ALL_MCAST flag which is more
guaranteed to succeed.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manage the -EPROBE_DEFER error case for "stm32_pwr_wakeup" IRQ.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Fixes: 4acb20b46214 ("net: socionext: different approach on DMA")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are spelling mistakes in structure elements, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac_check_ether_addr() checks the MAC address and assigns one in
driver open(). In many cases when we create slave netdevice, the dev
addr is inherited from master but the master dev addr maybe NULL at
that time, so move this call to driver probe so that address is
always valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Tested-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Sneh Shah <snehshah@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Querying EEPROM high pages data for SFP module is currently
not supported by our driver and yet queried, resulting in
invalid FW queries.
Set the EEPROM ethtool data length to 256 for SFP module will
limit the reading for page 0 only and prevent invalid FW queries.
Fixes: bb64143eee8c ("net/mlx5e: Add ethtool support for dump module EEPROM")
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MLX5E_XDP_MAX_MTU was calculated incorrectly. It didn't account for
NET_IP_ALIGN and MLX5E_HW2SW_MTU, and it also misused MLX5_SKB_FRAG_SZ.
This commit fixes the calculations and adds a brief explanation for the
formula used.
Fixes: a26a5bdf3ee2d ("net/mlx5e: Restrict the combination of large MTU and XDP")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
xdp_return_frame releases the frame. It leads to releasing the page, so
it's not allowed to access xdpi.xdpf->len after that, because xdpi.xdpf
is at xdp->data_hard_start after convert_to_xdp_frame. This patch moves
the memory access to precede the return of the frame.
Fixes: 58b99ee3e3ebe ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Since there are more IOT2040 variants with identical hardware but
different asset tags, the asset tag matching should be adjusted to
support them.
For the board name "SIMATIC IOT2000", currently there are 2 types of
hardware, IOT2020 and IOT2040. The IOT2020 is identified by its unique
asset tag. Match on it first. If we then match on the board name only,
we will catch all IOT2040 variants. In the future there will be no other
devices with the "SIMATIC IOT2000" DMI board name but different
hardware.
Signed-off-by: Su Bao Cheng <baocheng.su@siemens.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba0914 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b8195306694 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a couple of spelling mistakes in NL_SET_ERR_MSG_MOD error
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc warn this:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c: In function ndesc_init_rx_desc:
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:138:6: warning: variable 'bfsize1' set but not used [-Wunused-but-set-variable]
Like enh_desc_init_rx_desc, we should use bfsize1
in ndesc_init_rx_desc to calculate 'p->des1'
Fixes: 583e63614149 ("net: stmmac: use correct DMA buffer size in the RX descriptor")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Preemption disabled at:
[<ffff000008cabd54>] dev_set_rx_mode+0x1c/0x38
Call trace:
[<ffff00000808a5c0>] dump_backtrace+0x0/0x3d0
[<ffff00000808a9a4>] show_stack+0x14/0x20
[<ffff000008e6c0c0>] dump_stack+0xac/0xe4
[<ffff0000080fe76c>] ___might_sleep+0x164/0x238
[<ffff0000080fe890>] __might_sleep+0x50/0x88
[<ffff0000082261e4>] kmem_cache_alloc+0x17c/0x1d0
[<ffff000000ea0ae8>] ocelot_set_rx_mode+0x108/0x188 [mscc_ocelot_common]
[<ffff000008cabcf0>] __dev_set_rx_mode+0x58/0xa0
[<ffff000008cabd5c>] dev_set_rx_mode+0x24/0x38
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a BNX2X_ERR message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-04-09
This series provides some fixes to mlx5 driver.
I've cc'ed some of the checksum fixes to Eric Dumazet and i would like to get
his feedback before you pull.
For -stable v4.19
('net/mlx5: FPGA, tls, idr remove on flow delete')
('net/mlx5: FPGA, tls, hold rcu read lock a bit longer')
For -stable v4.20
('net/mlx5e: Rx, Check ip headers sanity')
('Revert "net/mlx5e: Enable reporting checksum unnecessary also for L3 packets"')
('net/mlx5e: Rx, Fixup skb checksum for packets with tail padding')
For -stable v5.0
('net/mlx5e: Switch to Toeplitz RSS hash by default')
('net/mlx5e: Protect against non-uplink representor for encap')
('net/mlx5e: XDP, Avoid checksum complete when XDP prog is loaded')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Separate the overflow handling from the hardware interrupt status analysis.
The interrupt status is a single register and is common for all PFs. The
first PF reading the register is not necessarily the one who overflowed.
All PFs must check their overflow status on every attention.
In this change we clear the sticky indication in the attention handler to
allow doorbells to be processed again as soon as possible, but running
the doorbell recovery is scheduled for the periodic handler to reduce the
time spent in the attention handler.
Checking the need for DORQ flush was changed to "db_bar_no_edpm" because
qed_edpm_enabled()'s result could change dynamically and might have
prevented a needed flush.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the DORQ (doorbell block) is overflowed, all PFs get attentions at the
same time. If one PF finished handling the attention before another PF even
started, the second PF might miss the DORQ's attention bit and not handle
the attention at all.
If the DORQ attention is missed and the issue is not resolved, another
attention will not be sent, therefore each attention is treated as a
potential DORQ attention.
As a result, the attention callback is called more frequently so the debug
print was moved to reduce its quantity.
The number of periodic doorbell recovery handler schedules was reduced
because it was the previous way to mitigating the missed attention issue.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the condition which verifies that doorbell address is inside the
doorbell bar by checking that the end of the address is within range
as well.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DB_REC_DRY_RUN (running doorbell recovery without sending doorbells) is
never used. DB_REC_ONCE (send a single doorbell from the doorbell recovery)
is not needed anymore because by running the periodic handler we make sure
we check the overflow status later instead.
This patch is needed because in the next patches, the only doorbell
recovery type being used is DB_REC_REAL_DEAL, and the fixes are much
cleaner without this enum.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The err2 error return path calls qede_ptp_disable that cleans up
on an error and frees ptp. After this, the free'd ptp is dereferenced
when ptp->clock is set to NULL and the code falls-through to error
path err1 that frees ptp again.
Fix this by calling qede_ptp_disable and exiting via an error
return path that does not set ptp->clock or kfree ptp.
Addresses-Coverity: ("Write to pointer after free")
Fixes: 035744975aec ("qede: Add support for PTP resource locking.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if a pci dma mapping failure is detected a free'd
memblock address is returned rather than a NULL (that indicates
an error). Fix this by ensuring NULL is returned on this error case.
Addresses-Coverity: ("Use after free")
Fixes: 528f727279ae ("vxge: code cleanup and reorganization")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some SOC like i.MX6SX clock have some limits:
- ahb clock should be disabled before ipg.
- ahb and ipg clocks are required for MAC MII bus.
So, move the ahb clock to runtime management together with
ipg clock.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thunderx driver forbids to load an eBPF program if the MTU is too high,
but this can be circumvented by loading the eBPF, then raising the MTU.
Fix this by limiting the MTU if an eBPF program is already loaded.
Fixes: 05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thunderx driver splits frames bigger than 1530 bytes to multiple
pages, making impossible to run an eBPF program on it.
This leads to a maximum MTU of 1508 if QinQ is in use.
The thunderx driver forbids to load an eBPF program if the MTU is higher
than 1500 bytes. Raise the limit to 1508 so it is possible to use L2
protocols which need some more headroom.
Fixes: 05c773f52b96e ("net: thunderx: Add basic XDP support")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53d7 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682ab ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e92087 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
