| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data. These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly. Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool support to show and set the device channel configuration.
Changing the channel configuration will result in a device restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool support to show and set the number of the Rx and Tx ring
descriptors. Changing the ring configuration will result in a device
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Read and save the port property registers once during the device probe
and then use the saved values as they are needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add some additional statistics for tracking VXLAN packets and checksum
errors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware has the capability to perform checksum offload support
(both Tx and Rx) and TSO support for VXLAN packets. Add the support
required to enable this.
The hardware can only support a single VXLAN port for offload. If more
than one VXLAN port is added then the offload capabilities have to be
disabled and can no longer be advertised.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert from using the old u32 supported, advertising, etc. link settings
to the new link mode settings that support bit positions / settings
greater than 32 bits.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add per queue Tx and Rx packet and byte counts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently whenever the driver needs to enable or disable interrupts for
a DMA channel it reads the interrupt enable register (IER), updates the
value and then writes the new value back to the IER. Since the hardware
does not change the IER, software can track this value and elimiate the
need to read it each time.
Add the IER value to the channel related data structure and use that as
the base for enabling and disabling interrupts, thus removing the need
for the MMIO read.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many of the names used by the driver are based upon the name of the device
found during device probe. Move the formatting of the names into the
device open function so that any renaming that occurs before the device is
brought up will be accounted for. This also means moving the creation of
some named workqueues into the device open path.
Add support to register for net events so that if a device is renamed
the corresponding debugfs directory can be renamed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
these drivers use tasklets or irq apis, but don't include interrupt.h.
Once flow cache is removed the implicit interrupt.h inclusion goes away
which will break the build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to change some general performance settings and to provide
some performance settings based on the device that is probed.
This includes:
- Setting the maximum read/write outstanding request limit
- Reducing the AXI interface burst length size
- Selectively setting the Tx and Rx descriptor pre-fetch threshold
- Selectively setting additional cache coherency controls
Tested and verified on all versions of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver hardcodes the PBLx8 setting. Remove the need for
specifying the PBLx8 setting and automatically calculate based on the
specified PBL value. Since the PBLx8 setting applies to both Tx and Rx
use the same PBL value for both of them.
Also, the driver currently uses a bit field to set the AXI master burst
len setting. Change to the full bit field range and set the burst length
based on the specified value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In prep for setting fine grained read and write DMA cache coherency
controls, allow specific values to be used to set the cache coherency
registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For IRQ affinity, set the affinity hints for the IRQs to be (initially) on
the processors corresponding to the NUMA node of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to perform memory allocations on the node of the device. The
original allocation or the ring structure and Tx/Rx queues allocated all
of the memory at once and then carved it up for each channel and queue.
To best ensure that we get as much memory from the NUMA node as we can,
break the channel and ring allocations into individual allocations.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the device interrupts should function as level interrupts. For
some hardware configurations this requires setting some control bits
so that if the interrupt status has not been cleared the interrupt
should be reissued.
Additionally, when using MSI or MSI-X interrupts, run the interrupt
service routine as a tasklet so that the re-issuance of the interrupt
is handled properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
|
|
A newer version of the hardware is using the same PCI ids for the network
device but has altered register definitions for determining the window
settings for the indirect PCS access. Add support to check for this
hardware and if found use the new register values.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the PCI MSI/MSI-X functions have been deprecated and it is
recommended to use the new pci_alloc_irq_vectors() function. Convert the
code over to use the new function. Also, modify the way in which the IRQs
are requested - try for multiple MSI-X/MSI first, then a single MSI/legacy
interrupt.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This patch provides support for the presence of a KR redriver chip in
between the device PCS and an external PHY. When a redriver chip is
present the device must perform clause 73 auto-negotiation in order to
set the redriver chip for the downstream connection.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the phylib support in the kernel to communicate with and control an
MDIO attached PHY. Use the hardware's MDIO communication mechanism to
communicate with the PHY.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for recognizing and using SFP+ modules directly. This includes
using the I2C support to read and interpret the information returned from
an SFP+ module and configuring things properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to initialize and use the I2C controller within the hardware
in order to perform sideband communication, e.g. determine the SFP media
type that is installed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some versions of the amd-xgbe device are capable of reporting ECC error
information back to the driver. Add support to process, track and report
on this information.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current per channel DMA interrupt support is based on an edge
triggered interrupt that is not maskable. This results in having to call
the disable_irq/enable_irq functions in order to prevent interrupts
during napi processing. The hardware now has a way to configure the per
channel DMA interrupt that will allow for masking the interrupt which
prevents calling disable_irq/enable_irq now. This patch makes use of
this support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for new PCI devices to the driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the reading of the Tx timestamp to account for a hardware issue
on how the fields and interrupt are cleared. The "seconds" portion of
the timestamp should be read first, followed by the "nanoseconds" portion.
Reading the "nanoseconds" portion should clear the timestamp data and the
interrupt. Because of an issue with the hardware this order is reversed
and reading the "seconds" portion actually clears the timestamp. The code
currently follows this workaround, but to guard against future versions
where this is fixed add a field to the version data to indicate if the
workaround is required or not.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the driver framework to separate out platform/ACPI specific code
from general code during device initialization. This will allow for the
introduction of PCI device support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx and Rx DMA channel status determiniation is different depending on the
version of the hardware. Update the channel status processing code to
account for the change. Also, reduce the timeout value used when stopping
the channels.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for reading all management counter registers as 64-bit
values. The indication of whether to read the high 32-bits to form
a 64-bit value is indicated in the version data.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare the code to be able to support accessing of the PCS registers
in a new way, while maintaining the current access method. Provide a
version specific field that indicates the method to use.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to be able to use clause 37 auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare for the future introduction of clause 37 auto-negotiation by
updating the current auto-negotiation related functions to identify
them as clause 73 functions. Move interrupt enablement to the
enable/disable auto-negotiation functions. Update what will be common
routines to check for the current type of AN and process accordingly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prepare the code to be able to work with more than one type of phy by
adding additional callable functions into the phy interface and removing
phy specific settings/functions from non-phy related files.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allocate the FIFO across the hardware Rx queues based on the priority
of the queues. Giving more FIFO resources to queues with a higher
priority. If PFC is active but not enabled for a queue, then less
resources can allocated to the queue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the Rx and Tx fifos are evenly allocated between the hardware
queues of the device. As more queues are instantiated, the fifo memory
needs to be able to be allocated based on queue priority. This allows for
higher priority queues to have more fifo memory than lower priority
queues. Prepare for this by modifying the current fifo calculation to
assign the fifo queue allocation in an array that is then used to program
the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Casting away const is bad practice. Since this is ARM specific driver
don't have hardware actually test this.
Having getter functions for ops is really unnecessary code bloat, but
not going to touch that.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the auto-negotiation interrupt handling disables the irq
instead of masking off the interrupts. This was done because the phy
library was originally used to read and write the PCS registers, which
could not be performed in interrupt context. Now that the phy library is
no longer used to read and write the PCS registers the interrupts can be
masked off in the interrupt service routine eliminating the need to call
disable_irq/enable_irq. This also requires changing the protection mutex
to a spinlock.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the netdev traffic class setup is only performed when invoked
through the ndo_setup_tc interface. However, the same setup should be
performed when the dcbnl interface (ieee_setets) is invoked. Rework the
netdev traffic class setup to be invokable through either interface and
also provide the priority to traffic class mapping if available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The XGBE_LINK bit is used just to determine whether to call the
netif_carrier_on/off functions. Rather than define and use this bit,
just call the functions. The netif_carrier_ok function can be used in
place of checking the XGBE_LINK bit in the future.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a statistic that tracks how many times an interrupt is generated for
a receive buffer not being available to the hardware which prevents the
hardware from being able to DMA the received data.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The calculation of the Tx and Rx fifo sizes can be calculated rather
than hardcoded in a switch statement. Additionally, the per-queue fifo
sizes can be calculated rather than hardcoded using if/else if statements
that can possibly underutilize the available fifo area.
Change the code to calculate the fifo sizes and the per-queue fifo sizes
to simplify the code and make best use of the available fifo.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
|
When running a kernel configured with CONFIG_DMA_API_DEBUG=y a warning
is issued:
DMA-API: device driver tries to sync DMA memory it has not allocated
This warning is the result of mapping the full range of the Rx buffer
pages allocated and then performing a dma_sync_single_for_cpu against
a calculated DMA address. The proper thing to do is to use the
dma_sync_single_range_for_cpu with a base DMA address and an offset.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow control negotiation logic is flawed and does not properly
advertise and process auto-negotiation of the flow control settings.
Update the flow control support to properly set the flow control
auto-negotiation settings and process the results approrpriately.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the device tree support of the amd-xgbe driver by defining
the PHY-related resources within the ethernet device node. The support
provides backwards compatibility with the original way.
Update the driver version to 1.0.2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
