| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
circuit
KSZ8794CNX datasheet section 8.0 RESET CIRCUIT describes recommended
circuit for interfacing with CPU/FPGA reset consisting of 10k pullup
resistor and 10uF capacitor to ground. This circuit takes ~100 ms to
rise enough to release the reset.
For maximum supply voltage VDDIO=3.3V VIH=2.0V R=10kR C=10uF that is
VDDIO - VIH
t = R * C * -ln( ------------- ) = 10000*0.00001*-(-0.93)=0.093 s
VDDIO
so we need ~95 ms for the reset to really de-assert, and then the
original 100us for the switch itself to come out of reset. Simply
msleep() for 100 ms which fits the constraint with a bit of extra
space.
Fixes: 5b797980908a ("net: dsa: microchip: Implement recommended reset timing")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210120030502.617185-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ8795 switch has 4 external ports {0,1,2,3} and 1 CPU port {4}, so
does the KSZ8765. The KSZ8794 seems to be repackaged KSZ8795 with different
ID and port 3 not routed out, however the port 3 registers are present in
the silicon, so the KSZ8794 switch has 3 external ports {0,1,2} and 1 CPU
port {4}. Currently the driver always uses the last port as CPU port, on
KSZ8795/KSZ8765 that is port 4 and that is OK, but on KSZ8794 that is port
3 and that is not OK, as it must also be port 4.
This patch adjusts the driver such that it always registers a switch with
5 ports total (4 external ports, 1 CPU port), always sets the CPU port to
switch port 4, and then configures the external port mask according to
the switch model -- 3 ports for KSZ8794 and 4 for KSZ8795/KSZ8765.
Fixes: 68a1b676db52 ("net: dsa: microchip: ksz8795: remove superfluous port_cnt assignment")
Fixes: 4ce2a984abd8 ("net: dsa: microchip: ksz8795: use phy_port_cnt where possible")
Fixes: 241ed719bc98 ("net: dsa: microchip: ksz8795: use port_cnt instead of TOTOAL_PORT_NUM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120001045.488506-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The value of the define VLAN_TABLE_ENTRIES can be derived from
num_vlans. This patch is using the variable num_vlans instead and
removes the extra define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To get the driver working with other chips using different port counts
the dyn_mac_table should be flushed depending on the amount of available
ports. This patch remove the extra define TOTOAL_PORT_NUM and is
making use of the dynamic port_cnt variable instead.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable mib_port_cnt has the same meaning as port_cnt.
This driver removes the extra variable and is using port_cnt
everywhere instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ksz8795 driver is using port_cnt differently to the other microchip
DSA drivers. It sets it to the external physical port count, than the
whole port count (including the cpu port). This patch is aligning the
variables purpose with the other microchip drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable num_ports is already assigned in the init function. The
drivers individual init function already handles the different purpose
of port_cnt vs port_cnt + 1. This patch removes the extra assignment of
the variable.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver is currently hard coded to SWITCH_PORT_NUM being
(TOTAL_PORT_NUM - 1) which is limited to 4 user ports for the ksz8795.
The phy_port_cnt is referring to its user ports. The patch removes the
extra define and use the assigned variable phy_port_cnt instead so the
driver can be used on different switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable mib_cnt is assigned with TOTAL_SWITCH_COUNTER_NUM. This
value can also be derived from the array size of mib_names. This patch
uses this calculated value instead, removes the extra define and uses
mib_cnt everywhere possible instead of the static define
TOTAL_SWITCH_COUNTER_NUM. Keeping it in a separate variable instead of
using ARRAY_SIZE everywhere instead makes the driver more flexible for
future use of devices with different amount of counters.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The extra define SWITCH_COUNTER_NUM is a copy of the KSZ8795_COUNTER_NUM
define. This patch initializes reg_mib_cnt with KSZ8795_COUNTER_NUM,
makes use of reg_mib_cnt everywhere instead and removes the extra
define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch moves all variable assignments to the init function. It
leaves the detect function for its single purpose to detect which chip
version is found.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The port_cnt assignment will be done again in the init function.
This patch removes the previous assignment in the detect function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The variable last_port is not used anywhere, this patch removes it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This should be done in the device driver instead of the device tree.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dsa.yaml device tree binding allows "ethernet-ports" (preferred) and
"ports".
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa86 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
(the DSA framework just checks for the presence of the .port_vlan_add
and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime
Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.
So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.
Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous implementation failed to account for the "ports" node. The
actual port nodes are not child nodes of the switch node, but a "ports"
node sits in between.
Fixes: edecfa98f602 ("net: dsa: microchip: look for phy-mode in port nodes")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.
It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).
Fixes: af199a1a9cb0 ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/devicetree/bindings/net/dsa/dsa.txt says that the phy-mode
property should be specified on port nodes. However, the microchip
drivers read it from the switch node.
Let the driver use the per-port property and fall back to the old
location with a warning.
Fix in-tree users.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Link: https://lore.kernel.org/netdev/20200617082235.GA1523@laureti-dev/
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The datasheet for the ksz9893 and ksz9477 switches recommend waiting at
least 100us after the de-assertion of reset before trying to program the
device through any interface.
Also switch the existing msleep() call to usleep_range() as recommended
in Documentation/timers/timers-howto.rst. The 2ms range used here is
somewhat arbitrary, as long as the reset is asserted for at least 10ms
we should be ok.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't assume that the link partner supports the in-band status
reporting which is enabled by default on the KSZ9893 when using RGMII
for the upstream port.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Always print the selected phy mode for the CPU port when using the
ksz9477 driver. If the phy mode was changed, also print the previous
mode to aid in debugging.
To make the message more clear, prefix it with the port number which it
applies to and improve the language a little.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make switch detection more informative print the result of the
ksz9477/ksz9893 compatibility check. With debug output enabled also
print the contents of the Chip ID registers as a 40-bit hex string.
As this detection is the first communication with the switch performed
by the driver, making it easy to see any errors here will help identify
issues with SPI data corruption or reset sequencing.
Signed-off-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Private structure members live_ports, on_ports, rx_ports, tx_ports are
initialized but not used anywhere. Let's remove them.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA subsystem moved to phylink and adjust_link() became deprecated in
the process. This patch removes adjust_link from the KSZ DSA switches and
adds phylink_mac_link_up() and phylink_mac_link_down().
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9893 3-Port Gigabit Ethernet Switch can be controlled via SPI,
I²C or MDIO (very limited and not supported by this driver). While there
is already a compatible entry for the SPI bus, it was missing for I²C.
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ protocol tag is needed by the KSZ DSA drivers.
Fixes: 0b9f9dfbfab4 ("dsa: Allow tag drivers to be built as modules")
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify ksz_common.c by using delayed_work instead of a combination of
timer and work.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This matches /sys/devices/.../spi1.0/modalias content.
Fixes: 9b2d9f05cddf ("net: dsa: microchip: add ksz9567 to ksz9477 driver")
Fixes: d9033ae95cf4 ("net: dsa: microchip: add KSZ8563 compatibility string")
Fixes: 8c29bebb1f8a ("net: dsa: microchip: add KSZ9893 switch support")
Fixes: 45316818371d ("net: dsa: add support for ksz9897 ethernet switch")
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Several cases of overlapping changes which were for the most
part trivially resolvable.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style
in header files related to Distributed Switch Architecture
drivers for Microchip KSZ series switch support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The regmap stride is set to 1 for regmap describing 8bit registers already.
However, for 16/32/64bit registers, the stride is 2/4/8 respectively. This
is not correct, as the switch protocol supports unaligned register reads
and writes and the KSZ87xx even uses such unaligned register accesses to
read e.g. MIB counter.
This patch fixes MIB counter access on KSZ87xx.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Fixes: 46558d601cb6 ("net: dsa: microchip: Initial SPI regmap support")
Fixes: 255b59ad0db2 ("net: dsa: microchip: Factor out regmap config generation into common header")
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the KSZ9567 7-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9567 supports both SPI and I2C. Oddly the
ksz9567 is already in the device tree binding documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
