| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There's a new version of Terratec H6 with uses USB ID
0ccd:10b2. This version is similar to the old one (with is
supported via the HTC entry), except that this one has the
eeprom on the second bus.
On this board, one side of this board is labeled with:
dvbc v2.0
The other side with:
94V-0, MO2, RK-4221 with huge digits: 1107
With those patches, the board is properly detected:
em28xx 1-1.5:1.0: New device TERRATEC TERRATCE H5 MKII @ 480 Mbps (0ccd:10b2, interface 0, class 0)
em28xx 1-1.5:1.0: Audio interface 0 found (Vendor Class)
em28xx 1-1.5:1.0: Video interface 0 found: isoc
em28xx 1-1.5:1.0: DVB interface 0 found: isoc
em28xx 1-1.5:1.0: chip ID is em2884
em28xx eeprom 00000000: 26 00 00 00 02 0b 0f e5 f5 64 01 60 09 e5 f5 64 &........d.`...d
em28xx eeprom 00000010: 09 60 03 c2 c6 22 e5 f7 b4 03 13 e5 f6 b4 87 03 .`..."..........
em28xx eeprom 00000020: 02 0a b9 e5 f6 b4 93 03 02 09 46 c2 c6 22 c2 c6 ..........F.."..
em28xx eeprom 00000030: 22 00 60 00 ef 70 08 85 3d 82 85 3c 83 93 ff ef ".`..p..=..<....
em28xx eeprom 00000040: 60 19 85 3d 82 85 3c 83 e4 93 12 07 a3 12 0a fe `..=..<.........
em28xx eeprom 00000050: 05 3d e5 3d 70 02 05 3c 1f 80 e4 22 12 0b 06 02 .=.=p..<..."....
em28xx eeprom 00000060: 07 e2 01 00 1a eb 67 95 cd 0c b2 10 f0 13 6b 03 ......g.......k.
em28xx eeprom 00000070: 98 22 6a 1c 86 12 27 57 4e 16 29 00 60 00 00 00 ."j...'WN.).`...
em28xx eeprom 00000080: 02 00 00 00 5e 00 13 00 f0 10 44 82 82 00 00 00 ....^.....D.....
em28xx eeprom 00000090: 5b 81 c0 00 00 00 20 40 20 80 02 20 10 01 00 00 [..... @ .. ....
em28xx eeprom 000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
em28xx eeprom 000000b0: c6 40 00 00 81 00 00 00 00 00 00 00 00 c4 00 00 .@..............
em28xx eeprom 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1c 03 ................
em28xx eeprom 000000d0: 31 00 32 00 33 00 34 00 35 00 36 00 37 00 38 00 1.2.3.4.5.6.7.8.
em28xx eeprom 000000e0: 39 00 41 00 42 00 43 00 44 00 12 03 54 00 45 00 9.A.B.C.D...T.E.
em28xx eeprom 000000f0: 52 00 52 00 41 00 54 00 45 00 43 00 22 03 54 00 R.R.A.T.E.C.".T.
em28xx 1-1.5:1.0: eeprom 000100: ... (skipped)
em28xx 1-1.5:1.0: EEPROM ID = 26 00 00 00, EEPROM hash = 0xbcd5a8cf
em28xx 1-1.5:1.0: EEPROM info:
em28xx 1-1.5:1.0: microcode start address = 0x0004, boot configuration = 0x00
em28xx 1-1.5:1.0: I2S audio, 5 sample rates
em28xx 1-1.5:1.0: 500mA max power
em28xx 1-1.5:1.0: Table at offset 0x27, strings=0x2298, 0x1c6a, 0x1286
em28xx 1-1.5:1.0: Identified as Terratec Cinergy H6 rev. 2 (card=101)
em28xx 1-1.5:1.0: Currently, V4L2 is not supported on this model
em28xx 1-1.5:1.0: dvb set to isoc mode.
usbcore: registered new interface driver em28xx
em28xx 1-1.5:1.0: Binding audio extension
em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2007-2016 Mauro Carvalho Chehab
em28xx 1-1.5:1.0: Endpoint 0x83 high-speed on intf 0 alt 7 interval = 8, size 196
em28xx 1-1.5:1.0: Number of URBs: 1, with 64 packets and 192 size
em28xx 1-1.5:1.0: Audio extension successfully initialized
em28xx: Registered (Em28xx Audio Extension) extension
em28xx 1-1.5:1.0: Binding DVB extension
drxk: status = 0x639260d9
drxk: detected a drx-3926k, spin A3, xtal 20.250 MHz
drxk: DRXK driver version 0.9.4300
drxk: frontend initialized.
tda18271 4-0060: creating new instance
tda18271: TDA18271HD/C2 detected @ 4-0060
dvbdev: DVB: registering new adapter (1-1.5:1.0)
em28xx 1-1.5:1.0: DVB: registering adapter 0 frontend 0 (DRXK DVB-C DVB-T)...
dvbdev: dvb_create_media_entity: media entity 'DRXK DVB-C DVB-T' registered.
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
em28xx 1-1.5:1.0: DVB extension successfully initialized
em28xx: Registered (Em28xx dvb Extension) extension
em28xx 1-1.5:1.0: Registering input extension
rc rc0: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0
Registered IR keymap rc-nec-terratec-cinergy-xs
input: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0/input0
em28xx 1-1.5:1.0: Input extension successfully initalized
em28xx: Registered (Em28xx Input Extension) extension
tda18271: performing RF tracking filter calibration
tda18271: RF tracking filter calibration complete
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The v4l2 dummy clock has been added with commit fc5d0f8a8878
("V4L2: em28xx: register a V4L2 clock source") to be able to use the ov2640
soc_camera driver.
Since commit 46796cfcd346 ("ov2640: use standard clk and enable it") it is
no longer required.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Hauppauge WinTV-dualHD model 01595 is a USB 2.0 dual ATSC/QAM tuner with
the following components:
USB bridge: Empia em28274
Demodulator: 2x LG LGDT3306a at addresses 0xb2 and 0x1c
Tuner: 2x Silicon Labs si2157 at addresses 0xc0 and 0xc4
This patch enables only the first tuner.
Signed-off-by: Kevin Cheng <kcheng@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Now that we're storing usb_interface at em28xx struct,
there's no good reason to keep storing usb_device, as we can
get it from usb_interface. So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The usb_device->dev is not the right device for dev_foo() calls.
Instead, it should use usb_interface->dev.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Instead of using pr_foo(), use dev_foo(), with provides a
better output. As this device is a multi-interface one,
we'll set the device name to show the chipset and the driver
used.
While here, get rid of printk continuation messages.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There's no reason to keep using em28xx-specific printk macros
here. Just use pr_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add the needed bits to make em28xx to create a media
controller graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The em28xx driver have lots of different input types but
only 4 of such types are actually used. The others are bogus.
Remove them, in order to cleanup the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch will add basic support for the Elgato EyeTV Hybrid INT
2008 USB Stick.
Signed-off-by: Gilles Risch <gilles.risch@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
https://lkml.org/lkml/2014/7/11/794
I used it with those arguments:
$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]
It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.
Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Terratec Cinergy T2 Stick HD [eb1a:8179] is a USB DVB-T/T2/C tuner that
contains following components:
* Empia EM28178 USB bridge
* Silicon Labs Si2168-A30 demodulator
* Silicon Labs Si2146-A10 tuner
I don't have the remote, so the RC_MAP is a best guess based on the pictures of
the remote controllers and other supported Terratec devices with a similar
remote.
[Antti: Resolved conflict caused by Leadtek VC100 patch]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Leadtek VC100 is a simple USB capture stick, similar to
Yakumo Movie Mixer.
Signed-off-by: Witold Krecicki <wpk+lkml@culm.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
* patchwork: (544 commits)
[media] ir-hix5hd2: fix build on c6x arch
[media] pt3: fix DTV FE I2C driver load error paths
Revert "[media] media: em28xx - remove reset_resume interface"
[media] exynos4-is: fix some warnings when compiling on arm64
[media] usb drivers: use %zu instead of %zd
[media] pci drivers: use %zu instead of %zd
[media] dvb-frontends: use %zu instead of %zd
[media] s5p-mfc: Fix several printk warnings
[media] s5p_mfc_opr: Fix warnings
[media] ti-vpe: Fix typecast
[media] s3c-camif: fix dma_addr_t printks
[media] s5p_mfc_opr_v6: get rid of warnings when compiled with 64 bits
[media] s5p_mfc_opr_v5: Fix lots of warnings on x86_64
[media] em28xx: Fix identation
[media] drxd: remove a dead code
[media] saa7146: remove return after BUG()
[media] cx88: remove return after BUG()
[media] cx88: fix cards table CodingStyle
[media] radio-sf16fmr2: declare some structs as static
[media] radio-sf16fmi: declare pnp_attached as static
...
Conflicts:
Documentation/DocBook/media/v4l/compat.xml
|
|
Field has_audio in struct em28xx_audio_mode is used together with value
EM28XX_NO_AC97 of field ac97 to determine the internal type of audio
(none/i2s/ac97). This makes the code difficult to understand:
!audio_mode.has_audio && audio_mode.ac97 == EM28XX_NO_AC97 => no audio
!audio_mode.has_audio && audio_mode.ac97 != EM28XX_NO_AC97 => BUG
audio_mode.has_audio && audio_mode.ac97 == EM28XX_NO_AC97 => AC97 audio
audio_mode.has_audio && audio_mode.ac97 != EM28XX_NO_AC97 => I2S audio
Simplify the whole thing by introducing an enum em28xx_int_audio_type
which describes the internal audio type (none, ac97, i2s) and is hooked
directly to the device struct. Then get rid of field has_audio in struct
em28xx_audio_mode.
A follow-up patch will then remove struct em28xx_ac97_mode and finally
the whole struct em28xx_audio_mode.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
As far as we know devices can either have audio class or vendor class
usb interfaces but not both at the same time. Even if both interface
types could be provided by devices at the same time, the current code is
totally broken for that case.
So clean up and simplify the usb audio class handling by replacing
fields "has_audio_class" (device has usb audio class compliant
interface) and "has_alsa_audio" (device has vendor audio interface) in
struct em28xx with a single enum em28xx_usb_audio_type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Fields "ac97_feat", "ac97_vendor_id" and "i2s_samplerates" of struct
em28xx_audio_mode are used nowhere, except in function
em28xx_audio_setup(). So get rid of them and use local variables
instead.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 747dba7de2a51a3db58b665ed3bc8c07921546ec.
It breaks concurrent vbi and video capturing:
While v4l2->users is the number of users of the whole device (all device nodes),
v4l2_fh_is_singular() only checks the number of users of a specific device node.
As a result. if one device node is open and a second device node is opened
(closed), the device is reinitialized (streaming is stopped).
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of counting the number of opened file handles, use function
v4l2_fh_is_singular_file() in em28xx_v4l2_open() and em28xx_v4l2_close() to
determine if the file handle is the first/last opened one.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
struct em28xx_fh isn't needed anymore because the only used field which is left is struct v4l2_fh fh.
Use struct v4l2_fh directly and remvove struct em28xx_fh.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
em28xx to struct em28xx_audio
Both wq_trigger and stream_started are used only to control the em28xx
alsa streaming. They don't belong to em28xx common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The tuner address is only used by the v4l submodule and at tuner setup and
can be obtained from the board data directly (if specified).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The tda9887 chipset is part of the analog tuner. Move it out of
em28xx-cards.
Also, it is used only one time by the v4l2 sub-module at tuner setup.
With that, we can get rid of an additional data inside the em28xx
common structure.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Move V4L2-specific frequency cache to struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Despite being at the common em28xx struct, those two fields are
actually taking into account only the usage inside em28xx v4l2
submodule. So, move them out of the common struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
struct v4l2
Move some temporary capture tracking date to the em28xx_v4l2 struct,
as those info are used only by em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Move camera sensor resolution and xtal out of em28xx common struct,
as thore are used only by the em28xx v4l2 submodule.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
struct v4l2
The video progressive data fields belong to analog TV. Move them out
of the common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The analog format struct belongs to analog TV. Move it out of the
common em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
TV norm is specific to analog TV reception. move it out of the common
em28xx struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The video input mode and control data also belong only to the
analog side. move them to struct em28xx_v4l.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
em28xx to struct v4l2
The em28xx scaler data are used only for analog video. Move them to
struct em28xx_v4l2.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The video and VBI-specific VB2 queue and mutexes are used only by
the v4l2 sub-driver. Move them to the V4L2 struct, preventing
wasting memory if this sub-driver is not used.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
There are 3 struct video_device at the em28xx common struct,
for video, VBI and radio. They all are used only by the V4L2 driver.
So, move them to the v4l2-specific struct.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The current clock definition applies only to the V4L2 side of the
driver. Move its struct pointer to the v4l2_dev, where it belongs.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
em28xx to struct v4l2
Controls are only applicable to V4L2 module. Move the corresponding
data structs to the proper place.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
That reduces a little bit the memory footprint when em28xx-video
is not loaded.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
struct
Just a cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
em28xx_compression_disable() is a single line function which is called only one
time and this call also isn't needed.
Register 0x26 is always configured as part of the scaler configuration, which
in turn is always done when the resolution changes. And the initial resolution
setting is applied at first device open.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Just driver cleanup. No functional changes.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Empia EM28178, Silicon Labs Si2168, Silicon Labs Si2157.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
We can't free struct em28xx while one of the extensions is still
using it.
So, add a kref() to control it, freeing it only after the
extensions fini calls.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Some devices have a LED to indicate when DVB capture started.
Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This device is close to Kworld UB435-Q, but it uses a different
tuner. Add support for it.
Tested with both 8VSB and 256QAM modulations.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
