| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch takes the downstream AXI halt routine and applies it when
IS_V6() is true.
bod: Converted to readl_poll_timeout()
Removed poll timeout for LPI register, testing showed the value
would always timeout and work, so the polling did nothing of value.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Vote for min clk frequency for core clks during prepare and enable clocks
at boot sequence. Without this the controller clock runs at very low value
(9.6MHz) which is not sufficient to boot venus.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
At this time there is no need to differentiate between the two, we can
reuse the 4xx pm ops callback structure for 6xx.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In various places in the venus codebase we have if (IS_V4()) which takes
the code down paths for 4xx silicon. This logic is broadly applicable to
6xx silicon also. In this patch we add IS_V6() to various IS_V4() decision
locations.
Co-developed-by: Dikshita Agarwal <dikshita@qti.qualcomm.com>
Signed-off-by: Dikshita Agarwal <dikshita@qti.qualcomm.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
On 6xx we should read wrapper cpu status from the wrapper TZ register set.
Co-developed-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Co-developed-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This commit adds 6xx specific interrupt support, some register offsets and
bitmasks differ from 4xx, which we account for in this commit.
[bod: Added commit log. Moved register definition into commit]
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This patch adds a 6xx specific boot logic. The goal is to share as much
code as possible between 3xx, 4xx and 6xx silicon.
We need to do a different write to WRAPPER_INTR_MASK with an additional
write to CPU_CS_H2XSOFTINTEN_V6 and CPU_CS_X2RPMh_V6.
The other writes are the same for 6xx and non-6xx silicon albeit at
different absolute relative locations to the base of the venus address
space.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This commit points the IO base registers 6xx offsets when probing for 6xx
hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
6xx silicon needs to access registers from a AON base address range.
This commit defines the necessary variable for later use.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
6xx silicon needs to access registers from a wrapper trust-zone base
address range.
This commit defines the necessary variable for later use.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This commit adds the macro helper IS_V6() which will be used to
differentiate iris2/v6 silicon from previous versions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
- Add X2 RPMh registers and definitions from the downstream example.
- Add 6xx core power definitions
- Add 6xx AON definitions
- Add 6xx wrapper tz definitions
- Add 6xx wrapper interrupt definitions
- Add 6xx soft interrupt definitions
- Define wrapper LPI register offsets
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This commit defines a range of new base addresses for already defined
blocks.
- CPU_BASE_V6
- CPU_CS_BASE_V6
- CPU_IC_BASE_V6
- WRAPPER_BASE_V6
The base addresses of the blocks are slightly different for 6xx but, aside
from that are layout and bit compatible.
New 6xx specific block addresses will be added in separate commits.
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
An upcoming silicon change places a number of existing blocks within the
Venus at different relative offsets to the base address of IO region.
In order to handle this difference this patch changes the address offsets
of the registers to function as offsets relative to the relevant sub-block
of registers within the IO region not the base address of the IO region.
As a result of this change venus_readl() and venus_writel() are deleted.
Co-developed-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
New silicon means that the pre-determined offsets we have been using
in this driver no longer hold. Existing blocks of registers can exist at
different offsets relative to the IO base address.
This commit adds a routine to assign the IO base hooks a subsequent commit
will convert from absolute to relative addressing.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Adds an sm8250 compatible binding to the venus core.
Co-developed-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Co-developed-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The Venus driver has to control two reset signals related to
gcc video_axi0 and videocc mvs0c for v6. Add it.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently hfi_platform_v6.c adds a bunch of capability parameters.
Reviewing downstream we can see a number of these need to be updated.
techpack/video/msm/vidc/msm_vidc_platform.c :: kona_capabilities[]
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Create CLL and Mastering display colour volume v4l2 controls for
encoder, add handling of HDR10 PQ SEI packet payloads for v4.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Adds support for decoder conceal color control.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The property is supported from v1 and upwards. So move it to
set_property_1x.
Fixes: 01e869e78756 ("media: venus: venc: fix handlig of S_SELECTION and G_SELECTION")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
It is observed that on Venus v1 the default header-mode is producing
a bitstream which is not playble. Change the default header-mode to
joined with 1st frame.
Fixes: 002c22bd360e ("media: venus: venc: set inband mode property to FW.")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The rate of the core clock is set through devm_pm_opp_set_rate and
to avoid errors from it we have to set the name of the clock via
dev_pm_opp_set_clkname.
Fixes: 9a538b83612c ("media: venus: core: Add support for opp tables/perf voting")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The inst function argument is != NULL only for Venus v1 and
we did not migrate v1 to a hfi_platform abstraction yet. So
check for instance != NULL only after hfi_platform_get returns
no error.
Fixes: e29929266be1 ("media: venus: Get codecs and capabilities from hfi platform")
Cc: stable@vger.kernel.org # v5.12
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The Venus v1 behaves differently comparing with the other Venus
version in respect to capability parsing and when they are send
to the driver. So we don't need to initialize hfi parser for
multiple invocations like what we do for > v1 Venus versions.
Fixes: 10865c98986b ("media: venus: parser: Prepare parser for multiple invocations")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for below LTR controls in encoder:
- V4L2_CID_MPEG_VIDEO_LTR_COUNT
- V4L2_CID_MPEG_VIDEO_FRAME_LTR_INDEX
- V4L2_CID_MPEG_VIDEO_USE_LTR_FRAMES
Signed-off-by: Dikshita Agarwal <dikshita@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Wrong solution of rebase conflict leads to calling twice
v4l2_device_unregister in .venus_remove. Delete the second one.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Enable support for SDM845 based Titan 170 ISPs.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
For Titan ISPs clocks fail to re-enable during vfe_get()
after any vfe has been halted and its corresponding power
domain power has been detached.
Since all of the clocks depend on all of the PDs, per
VFE PD detaching is no option for Gen2 HW.
In order to not have regressions on for Gen1 HW, refactor
the power domain management into hardware version specific
code paths.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add register definitions for version 170 of the Titan architecture
and implement support for the CSIPHY subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add register definitions for version 170 of the Titan architecture
and implement support for the CSID subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the CSID subdevice drivers needs to be refactored
to better abstract the different ISP hardware architectures.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The CSI-2 spec defines format identifier for Data Type (DT),
and how the Decode Format (DF) & Encode Format (EF) are implemented.
The spec does however not define the DF, EF or Plain Format (PF)
identifiers, as those are vendor specific.
Plain formats describe the size of the pixels written by the RDI
units to memory. PLAIN8 for example has the size 8 bits, and
PLAIN32 32 bits. The appropriate Plain Format is determined by
the Decode Format used. The smallest Plain Format that is able
to contain a pixel of the used Decode Format is the appropriate
one to use.
As the vendor specific identifiers differ between hardware
generations, split them out into separate headers.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add register definitions for version 170 of the Titan architecture
and implement support for the RDI output mode.
The RDI mode as opposed to the PIX output mode for the VFE unit does
not support any ISP functionality. This means essentially only
supporting dumping the output of the whatever the CSI decoder receives
from the sensor.
For example will a sensor outputting YUV pixel format frames, only
allow the VFE to dump those frames as they are received by the ISP
to memory through the RDI interface.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the VFE subdevice driver needs to be refactored
to better abstract the different ISP architectures.
Gen1 represents the CAMSS ISP architecture. The ISP architecture developed
after CAMSS, Titan, will be referred to as Gen2.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This driver supports multiple architecture versions of the Qualcomm ISP.
The CAMSS architecure which this driver is name after, and with the
introduction of this series, the Titan architecture.
The ISPIF is an IP-block that is only present in the CAMSS generation of
the architecture. In order to support the Titan generation, make the
ISPIF an optional subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add enum representing the SDM845 SOC, which incorporates version
170 of the Titan architecture ISP.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
trace_printk() should not be used in production code,
since extra memory is used for special buffers whenever
trace_puts() is used.
Replace it with dev_dbg() which provides all of the desired
debugging functionality.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Comment refers to ISPIF, but this is incorrect. Only
the VFE interrupts are handled by this function.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Function name in comment is wrong, and was changed to be
the same as the actual function name.
The comment was changed to kerneldoc format.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
On production devices the firmware could be located on different
places, this path could be provided by special firmware-name DT
property.
Here we check for existence of such DT property and if it exist
take the firmware path from there. Otherwise, if the property
is missing we fallback to the predefined path from driver resource
structure.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This file uses memremap() now, so we should include io.h instead of
relying on any sort of implicit include elsewhere.
Cc: Dikshita Agarwal <dikshita@codeaurora.org>
Fixes: 0ca0ca980505 ("media: venus: core: add support to dump FW region")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Fritz Koenig <frkoenig@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Commit aaaa93eda64b ("media] media: venus: venc: add video encoder files")
is the last in a series of three commits to add core.c vdec.c and venc.c
adding core, encoder and decoder.
The encoder and decoder check for core drvdata as set and return -EPROBE_DEFER
if it has not been set, however both the encoder and decoder rely on
core.v4l2_dev as valid.
core.v4l2_dev will not be valid until v4l2_device_register() has completed
in core.c's probe().
Normally this is never seen however, Dmitry reported the following
backtrace when compiling drivers and firmware directly into a kernel image.
[ 5.259968] Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
[ 5.269850] sd 0:0:0:3: [sdd] Optimal transfer size 524288 bytes
[ 5.275505] Workqueue: events deferred_probe_work_func
[ 5.275513] pstate: 60400005 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[ 5.441211] usb 2-1: new SuperSpeedPlus Gen 2 USB device number 2 using xhci-hcd
[ 5.442486] pc : refcount_warn_saturate+0x140/0x148
[ 5.493756] hub 2-1:1.0: USB hub found
[ 5.496266] lr : refcount_warn_saturate+0x140/0x148
[ 5.500982] hub 2-1:1.0: 4 ports detected
[ 5.503440] sp : ffff80001067b730
[ 5.503442] x29: ffff80001067b730
[ 5.592660] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 5.598478] x28: ffff6c6bc1c379b8
[ 5.598480] x27: ffffa5c673852960 x26: ffffa5c673852000
[ 5.598484] x25: ffff6c6bc1c37800 x24: 0000000000000001
[ 5.810652] x23: 0000000000000000 x22: ffffa5c673bc7118
[ 5.813777] hub 1-1:1.0: USB hub found
[ 5.816108] x21: ffffa5c674440000 x20: 0000000000000001
[ 5.820846] hub 1-1:1.0: 4 ports detected
[ 5.825415] x19: ffffa5c6744f4000 x18: ffffffffffffffff
[ 5.825418] x17: 0000000000000000 x16: 0000000000000000
[ 5.825421] x15: 00000a4810c193ba x14: 0000000000000000
[ 5.825424] x13: 00000000000002b8 x12: 000000000000f20a
[ 5.825427] x11: 000000000000f20a x10: 0000000000000038
[ 5.845447] usb 2-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
[ 5.845904]
[ 5.845905] x9 : 0000000000000000 x8 : ffff6c6d36fae780
[ 5.871208] x7 : ffff6c6d36faf240 x6 : 0000000000000000
[ 5.876664] x5 : 0000000000000004 x4 : 0000000000000085
[ 5.882121] x3 : 0000000000000119 x2 : ffffa5c6741ef478
[ 5.887578] x1 : 3acbb3926faf5f00 x0 : 0000000000000000
[ 5.893036] Call trace:
[ 5.895551] refcount_warn_saturate+0x140/0x148
[ 5.900202] __video_register_device+0x64c/0xd10
[ 5.904944] venc_probe+0xc4/0x148
[ 5.908444] platform_probe+0x68/0xe0
[ 5.912210] really_probe+0x118/0x3e0
[ 5.915977] driver_probe_device+0x5c/0xc0
[ 5.920187] __device_attach_driver+0x98/0xb8
[ 5.924661] bus_for_each_drv+0x68/0xd0
[ 5.928604] __device_attach+0xec/0x148
[ 5.932547] device_initial_probe+0x14/0x20
[ 5.936845] bus_probe_device+0x9c/0xa8
[ 5.940788] device_add+0x3e8/0x7c8
[ 5.944376] of_device_add+0x4c/0x60
[ 5.948056] of_platform_device_create_pdata+0xbc/0x140
[ 5.953425] of_platform_bus_create+0x17c/0x3c0
[ 5.958078] of_platform_populate+0x80/0x110
[ 5.962463] venus_probe+0x2ec/0x4d8
[ 5.966143] platform_probe+0x68/0xe0
[ 5.969907] really_probe+0x118/0x3e0
[ 5.973674] driver_probe_device+0x5c/0xc0
[ 5.977882] __device_attach_driver+0x98/0xb8
[ 5.982356] bus_for_each_drv+0x68/0xd0
[ 5.986298] __device_attach+0xec/0x148
[ 5.990242] device_initial_probe+0x14/0x20
[ 5.994539] bus_probe_device+0x9c/0xa8
[ 5.998481] deferred_probe_work_func+0x74/0xb0
[ 6.003132] process_one_work+0x1e8/0x360
[ 6.007254] worker_thread+0x208/0x478
[ 6.011106] kthread+0x150/0x158
[ 6.014431] ret_from_fork+0x10/0x30
[ 6.018111] ---[ end trace f074246b1ecdb466 ]---
This patch fixes by
- Only setting drvdata after v4l2_device_register() completes
- Moving v4l2_device_register() so that suspend/reume in core::probe()
stays as-is
- Changes pm_ops->core_function() to take struct venus_core not struct
device
- Minimal rework of v4l2_device_*register in probe/remove
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
If an error occurs after a successful 'of_icc_get()' call, it must be
undone.
Use 'devm_of_icc_get()' instead of 'of_icc_get()' to avoid the leak.
Update the remove function accordingly and axe the now unneeded
'icc_put()' calls.
Fixes: 32f0a6ddc8c9 ("media: venus: Use on-chip interconnect API")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for Access Unit Delimiter control into encoder.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add support for display delay and display delay enable std controls.
With this we implement decoder decode output order (decode vs display).
Once firmware implement few new features the controls will be used
for other use-cases.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Because of u32 type being used to store pixel clock rate, expression used
to calculate pipeline clocks (pixel_clock * bpp) produces wrong value due
to integer overflow. This patch changes data type used to store, pass and
retrieve pixel_clock from u32 to u64 to make this mistake less likely to
be repeated in the future.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are places in the camss driver where camss_get_pixel_clock() is
called to get the pixel rate (using V4L2_CID_PIXEL_RATE control) and to
calculate the link frequency from it. There is a case when this would
not work: when V4L2_CID_PIXEL_RATE gets the rate at which the pixels are
read (sampled) from the sensor's pixel array, and this rate is different
from the pixel transmission rate over the CSI link, the link frequency
value can't be calculated from the pixel rate. One needs to use
V4L2_CID_LINK_FREQ to get the link frequency in this case.
Replace such calls to camss_get_pixel_clock() with calls to a wrapper
around v4l2_get_link_freq(). v4l2_get_link_freq() tries V4L2_CID_LINK_FREQ
first, and if it is not implemented by the camera sensor driver, falls
back to V4L2_CID_PIXEL_RATE to calculate the link frequency value from.
Calls to camss_get_pixel_clock() from vfe_[check,set]_clock_rates()
are left intact as it looks like this VFE clock does depend on the
rate the pixel samples comes out of the camera sensor, not on the
frequency at which the link between the sensor and the CSI receiver
operates.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Linux 5.11-rc6
* tag 'v5.11-rc6': (1466 commits)
Linux 5.11-rc6
leds: rt8515: Add Richtek RT8515 LED driver
dt-bindings: leds: Add DT binding for Richtek RT8515
leds: trigger: fix potential deadlock with libata
leds: leds-ariel: convert comma to semicolon
leds: leds-lm3533: convert comma to semicolon
dt-bindings: Cleanup standard unit properties
soc: litex: Properly depend on HAS_IOMEM
tty: avoid using vfs_iocb_iter_write() for redirected console writes
null_blk: cleanup zoned mode initialization
cifs: fix dfs domain referrals
drm/nouveau/kms/gk104-gp1xx: Fix > 64x64 cursors
drm/nouveau/kms/nv50-: Report max cursor size to userspace
drivers/nouveau/kms/nv50-: Reject format modifiers for cursor planes
drm/nouveau/svm: fail NOUVEAU_SVM_INIT ioctl on unsupported devices
drm/nouveau/dispnv50: Restore pushing of all data.
io_uring: reinforce cancel on flush during exit
cifs: returning mount parm processing errors correctly
rxrpc: Fix memory leak in rxrpc_lookup_local
mlxsw: spectrum_span: Do not overwrite policer configuration
...
|
