summaryrefslogtreecommitdiff
path: root/drivers/md/md-cluster.c
AgeCommit message (Collapse)AuthorFilesLines
2016-05-09md-cluster: check the return value of process_recvd_msgGuoqing Jiang1-3/+10
We don't need to run the full path of recv_daemon if process_recvd_msg doesn't return 0. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-09md-cluster: gather resync infos and enable recv_thread after bitmap is readyGuoqing Jiang1-6/+24
The in-memory bitmap is not ready when node joins cluster, so it doesn't make sense to make gather_all_resync_info() called so earlier, we need to call it after the node's bitmap is setup. Also, recv_thread could be wake up after node joins cluster, but it could cause problem if node receives RESYNCING message without persionality since mddev->pers->quiesce is called in process_suspend_info. This commit introduces a new cluster interface load_bitmaps to fix above problems, load_bitmaps is called in bitmap_load where bitmap and persionality are ready, and load_bitmaps does the following tasks: 1. call gather_all_resync_info to load all the node's bitmap info. 2. set MD_CLUSTER_ALREADY_IN_CLUSTER bit to recv_thread could be wake up, and wake up recv_thread if there is pending recv event. Then ack_bast only wakes up recv_thread after IN_CLUSTER bit is ready otherwise MD_CLUSTER_PENDING_RESYNC_EVENT is set. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-04md-cluster: sync bitmap when node received RESYNCING msgGuoqing Jiang1-0/+27
If the node received RESYNCING message which means another node will perform resync with the area, then we don't want to do it again in another node. Let's set RESYNC_MASK and clear NEEDED_MASK for the region from old-low to new-low which has finished syncing, and the region from old-hi to new-hi is about to syncing, bitmap_sync_with_cluste is introduced for the purpose. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-04md-cluster: fix locking when node joins cluster during message broadcastGuoqing Jiang1-3/+10
If a node joins the cluster while a message broadcast is under way, a lock issue could happen as follows. For a cluster which included two nodes, if node A is calling __sendmsg before up-convert CR to EX on ack, and node B released CR on ack. But if a new node C joins the cluster and it doesn't receive the message which A sent before, so it could hold CR on ack before A up-convert CR to EX on ack. So a node joining the cluster should get an EX lock on the "token" first to ensure no broadcast is ongoing, then release it after held CR on ack. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-04md-cluster: unregister thread if err happenedGuoqing Jiang1-0/+2
The two threads need to be unregistered if a node can't join cluster successfully. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-04md-cluster: wake up thread to continue recoveryGuoqing Jiang1-3/+6
In recovery case, we need to set MD_RECOVERY_NEEDED and wake up thread only if recover is not finished. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-05-04md-cluster: change resync lock from asynchronous to synchronousGuoqing Jiang1-2/+0
If multiple nodes choose to attempt do resync at the same time they need to be serialized so they don't duplicate effort. This serialization is done by locking the 'resync' DLM lock. Currently if a node cannot get the lock immediately it doesn't request notification when the lock becomes available (i.e. DLM_LKF_NOQUEUE is set), so it may not reliably find out when it is safe to try again. Rather than trying to arrange an async wake-up when the lock becomes available, switch to using synchronous locking - this is a lot easier to think about. As it is not permitted to block in the 'raid1d' thread, move the locking to the resync thread. So the rsync thread is forked immediately, but it blocks until the resync lock is available. Once the lock is locked it checks again if any resync action is needed. A particular symptom of the current problem is that a node can get stuck with "resync=pending" indefinitely. Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-01-25md-cluster: fix missing memory freeShaohua Li1-1/+5
There are several places we allocate dlm_lock_resource, but not free it. leave() need free a lock resource too (from Guoqing) Cc: Goldwyn Rodrigues <rgoldwyn@suse.com> Cc: Guoqing Jiang <gqjiang@suse.com> Cc: NeilBrown <neilb@suse.com> Signed-off-by: Shaohua Li <shli@fb.com>
2016-01-06md-cluster: update comments for MD_CLUSTER_SEND_LOCKED_ALREADYGuoqing Jiang1-5/+18
1. fix unbalanced parentheses. 2. add more description about that MD_CLUSTER_SEND_LOCKED_ALREADY will be cleared after set it in add_new_disk. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: Protect communication with mutexesGuoqing Jiang1-10/+63
Communication can happen through multiple threads. It is possible that one thread steps over another threads sequence. So, we use mutexes to protect both the send and receive sequences. Send communication is locked through state bit, MD_CLUSTER_SEND_LOCK. Communication is locked with bit manipulation in order to allow "lock and hold" for the add operation. In case of an add operation, if the lock is held, MD_CLUSTER_SEND_LOCKED_ALREADY is set. When md_update_sb() calls metadata_update_start(), it checks (in a single statement to avoid races), if the communication is already locked. If yes, it merely returns zero, else it locks the token lockresource. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: Defer MD reloading to mddev->threadGuoqing Jiang1-1/+3
Reloading of superblock must be performed under reconfig_mutex. However, this cannot be done with md_reload_sb because it would deadlock with the message DLM lock. So, we defer it in md_check_recovery() which is executed by mddev->thread. This introduces a new flag, MD_RELOAD_SB, which if set, will reload the superblock. And good_device_nr is also added to 'struct mddev' which is used to get the num of the good device within cluster raid. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: append some actions when change bitmap from clustered to noneGuoqing Jiang1-0/+57
For clustered raid, we need to do extra actions when change bitmap to none. 1. check if all the bitmap lock could be get or not, if yes then we can continue the change since cluster raid is only active in current node. Otherwise return fail and unlock the related bitmap locks 2. set nodes to 0 and then leave cluster environment. 3. release other nodes's bitmap lock. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: Fix the remove sequence with the new MD reload codeGoldwyn Rodrigues1-1/+1
The remove disk message does not need metadata_update_start(), but can be an independent message. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: remove a disk asynchronously from cluster environmentGuoqing Jiang1-2/+5
For cluster raid, if one disk couldn't be reach in one node, then other nodes would receive the REMOVE message for the disk. In receiving node, we can't call md_kick_rdev_from_array to remove the disk from array synchronously since the disk might still be busy in this node. So let's set a ClusterRemove flag on the disk, then let the thread to do the removal job eventually. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2016-01-06md-cluster: Avoid the resync ping-pongGoldwyn Rodrigues1-0/+8
If a RESYNCING message with (0,0) has been sent before, do not send it again. This avoids a resync ping pong between the nodes. We read the bitmap lockresource's LVB to figure out the previous value of the RESYNCING message. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-24md-cluster: remove mddev arg from add_resync_info()NeilBrown1-3/+3
The arg isn't used, so its presence is only confusing. Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-24md-cluster: don't cast void pointers when assigning them.NeilBrown1-2/+2
It is common practice in the kernel to leave out this case. It isn't needed and adds little if any value. Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-24md-cluster: discard unused sb_mutex.NeilBrown1-2/+0
Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-24md-cluster: Fix warnings when build with CF=-D__CHECK_ENDIAN__Guoqing Jiang1-10/+11
This patches fixes sparse warnings like incorrect type in assignment (different base types), cast to restricted __le64. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-16md-cluster: metadata_update_finish: consistently use cmsg.raid_slot as le32NeilBrown1-4/+5
As cmsg.raid_slot is le32, comparing for >0 is not meaningful. So introduce cpu-endian 'raid_slot' and only assign to cmsg.raid_slot when we know value is valid. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-12md-cluster: Add 'SUSE' as author for md-cluster.cGuoqing Jiang1-0/+1
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
2015-10-12md-cluster: zero cmsg before it was sentGuoqing Jiang1-3/+3
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
2015-10-12md-cluster: make sure the node do not receive it's own msgGuoqing Jiang1-0/+3
During the past test, the node occasionally received the msg which is sent from itself, this case should not happen in theory, but it is better to avoid it in case something wrong happened. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: remove unnecessary setting for slotGuoqing Jiang1-2/+0
Since slot will be set within _sendmsg, we can remove the redundant code in resync_info_update. Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
2015-10-12md-cluster: make other members of cluster_msg is handled by little endian funcsGuoqing Jiang1-10/+14
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
2015-10-12md-cluster: Do not printk() every received messageGoldwyn Rodrigues1-14/+0
The receive daemon prints kernel messages for every network message received. This would fill the kernel message log with unnecessary messages. Remove the pr_info() messages. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: Fix adding of new disk with new reload codeGoldwyn Rodrigues1-10/+25
Adding the disk worked incorrectly with the new reload code. Fix it: - No operation should be performed on rdev marked as Candidate - After a metadata update operation, kick disk if role is 0xfffe else clear Candidate bit and continue with the regular change check. - Saving the mode of the lock resource to check if token lock is already locked, because it can be called twice while adding a disk. However, unlock_comm() must be called only once. - add_new_disk() is called by the node initiating the --add operation. If it needs to be canceled, call add_new_disk_cancel(). The operation is completed by md_update_sb() which will write and unlock the communication. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: Perform resync/recovery under a DLM lockGoldwyn Rodrigues1-3/+26
Resync or recovery must be performed by only one node at a time. A DLM lock resource, resync_lockres provides the mutual exclusion so that only one node performs the recovery/resync at a time. If a node is unable to get the resync_lockres, because recovery is being performed by another node, it set MD_RECOVER_NEEDED so as to schedule recovery in the future. Remove the debug message in resync_info_update() used during development. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: Improve md_reload_sb to be less error proneGoldwyn Rodrigues1-11/+16
md_reload_sb is too simplistic and it explicitly needs to determine the changes made by the writing node. However, there are multiple areas where a simple reload could fail. Instead, read the superblock of one of the "good" rdevs and update the necessary information: - read the superblock into a newly allocated page, by temporarily swapping out rdev->sb_page and calling ->load_super. - if that fails return - if it succeeds, call check_sb_changes 1. iterates over list of active devices and checks the matching dev_roles[] value. If that is 'faulty', the device must be marked as faulty - call md_error to mark the device as faulty. Make sure not to set CHANGE_DEVS and wakeup mddev->thread or else it would initiate a resync process, which is the responsibility of the "primary" node. - clear the Blocked bit - Call remove_and_add_spares() to hot remove the device. If the device is 'spare': - call remove_and_add_spares() to get the number of spares added in this operation. - Reduce mddev->degraded to mark the array as not degraded. 2. reset recovery_cp - read the rest of the rdevs to update recovery_offset. If recovery_offset is equal to MaxSector, call spare_active() to set it In_sync This required that recovery_offset be initialized to MaxSector, as opposed to zero so as to communicate the end of sync for a rdev. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: Wake up suspended processGoldwyn Rodrigues1-2/+5
When the suspended_area is deleted, the suspended processes must be woken up in order to complete their I/O. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
2015-10-12md-cluster: send BITMAP_NEEDS_SYNC when node is leaving clusterGuoqing Jiang1-0/+20
Previously, BITMAP_NEEDS_SYNC message is sent when the resyc aborts, but it could abort for different reasons, and not all of reasons require another node to take over the resync ownship. It is better make BITMAP_NEEDS_SYNC message only be sent when the node is leaving cluster with dirty bitmap. And we also need to ensure dlm connection is ok. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-10-12md-cluster: Use a small window for resyncGoldwyn Rodrigues1-36/+5
Suspending the entire device for resync could take too long. Resync in small chunks. cluster's resync window (32M) is maintained in r1conf as cluster_sync_low and cluster_sync_high and processed in raid1's sync_request(). If the current resync is outside the cluster resync window: 1. Set the cluster_sync_low to curr_resync_completed. 2. Check if the sync will fit in the new window, if not issue a wait_barrier() and set cluster_sync_low to sector_nr. 3. Set cluster_sync_high to cluster_sync_low + resync_window. 4. Send a message to all nodes so they may add it in their suspension list. bitmap_cond_end_sync is modified to allow to force a sync inorder to get the curr_resync_completed uptodate with the sector passed. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.de>
2015-10-12md-cluster: complete all write requests before adding suspend_infoGoldwyn Rodrigues1-2/+5
process_suspend_info - which handles the RESYNCING request - must not reply until all writes which were initiated before the request arrived, have completed. As a by-product, all process_* functions now take mddev as their first arguement making it uniform. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: remove inappropriate try_module_get from join()NeilBrown1-4/+0
md_setup_cluster already calls try_module_get(), so this try_module_get isn't needed. Also, there is no matching module_put (except in error patch), so this leaves an unbalanced module count. Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: Read the disk bitmap sb and check if it needs recoveryGuoqing Jiang1-1/+15
In gather_all_resync_info, we need to read the disk bitmap sb and check if it needs recovery. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: only call complete(&cinfo->completion) when node join clusterGuoqing Jiang1-1/+10
Introduce MD_CLUSTER_BEGIN_JOIN_CLUSTER flag to make sure complete(&cinfo->completion) is only be invoked when node join cluster. Otherwise node failure could also call the complete, and it doesn't make sense to do it. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: add missed lockres_freeGuoqing Jiang1-1/+3
We also need to free the lock resource before goto out. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: remove the unused sb_lockGuoqing Jiang1-9/+0
The sb_lock is not used anywhere, so let's remove it. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: init suspend_list and suspend_lock early in joinGuoqing Jiang1-3/+2
If the node just join the cluster, and receive the msg from other nodes before init suspend_list, it will cause kernel crash due to NULL pointer dereference, so move the initializations early to fix the bug. md-cluster: Joined cluster 3578507b-e0cb-6d4f-6322-696cd7b1b10c slot 3 BUG: unable to handle kernel NULL pointer dereference at (null) ... ... ... Call Trace: [<ffffffffa0444924>] process_recvd_msg+0x2e4/0x330 [md_cluster] [<ffffffffa0444a06>] recv_daemon+0x96/0x170 [md_cluster] [<ffffffffa045189d>] md_thread+0x11d/0x170 [md_mod] [<ffffffff810768c4>] kthread+0xb4/0xc0 [<ffffffff8151927c>] ret_from_fork+0x7c/0xb0 ... ... ... RIP [<ffffffffa0443581>] __remove_suspend_info+0x11/0xa0 [md_cluster] Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: add the error check if failed to get dlm lockGuoqing Jiang1-6/+35
In complicated cluster environment, it is possible that the dlm lock couldn't be get/convert on purpose, the related err info is added for better debug potential issue. For lockres_free, if the lock is blocking by a lock request or conversion request, then dlm_unlock just put it back to grant queue, so need to ensure the lock is free finally. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: init completion within lockres_initGuoqing Jiang1-2/+1
We should init completion within lockres_init, otherwise completion could be initialized more than one time during it's life cycle. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: fix deadlock issue on message lockGuoqing Jiang1-7/+7
There is problem with previous communication mechanism, and we got below deadlock scenario with cluster which has 3 nodes. Sender Receiver Receiver token(EX) message(EX) writes message downconverts message(CR) requests ack(EX) get message(CR) gets message(CR) reads message reads message requests EX on message requests EX on message To fix this problem, we do the following changes: 1. the sender downconverts MESSAGE to CW rather than CR. 2. and the receiver request PR lock not EX lock on message. And in case we failed to down-convert EX to CW on message, it is better to unlock message otherthan still hold the lock. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Lidong Zhong <ldzhong@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: transfer the resync ownership to another nodeGuoqing Jiang1-0/+15
When node A stops an array while the array is doing a resync, we need to let another node B take over the resync task. To achieve the goal, we need the A send an explicit BITMAP_NEEDS_SYNC message to the cluster. And the node B which received that message will invoke __recover_slot to do resync. Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: split recover_slot for future code reuseGuoqing Jiang1-7/+16
Make recover_slot as a wraper to __recover_slot, since the logic of __recover_slot can be reused for the condition when other nodes need to take over the resync job. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-08-31md-cluster: use %pU to print UUIDsGuoqing Jiang1-14/+2
Reviewed-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-07-24Fix read-balancing during node failureGoldwyn Rodrigues1-1/+11
During a node failure, We need to suspend read balancing so that the reads are directed to the first device and stale data is not read. Suspending writes is not required because these would be recorded and synced eventually. A new flag MD_CLUSTER_SUSPEND_READ_BALANCING is set in recover_prep(). area_resyncing() will respond true for the entire devices if this flag is set and the request type is READ. The flag is cleared in recover_done(). Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Reported-By: David Teigland <teigland@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com>
2015-04-22md-cluster: re-add capabilitiesGoldwyn Rodrigues1-1/+47
When "re-add" is writted to /sys/block/mdXX/md/dev-YYY/state, the clustered md: 1. Sends RE_ADD message with the desc_nr. Nodes receiving the message clear the Faulty bit in their respective rdev->flags. 2. The node initiating re-add, gathers the bitmaps of all nodes and copies them into the local bitmap. It does not clear the bitmap from which it is copying. 3. Initiating node schedules a md recovery to sync the devices. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22md-cluster: remove capabilitiesGoldwyn Rodrigues1-0/+30
This adds "remove" capabilities for the clustered environment. When a user initiates removal of a device from the array, a REMOVE message with disk number in the array is sent to all the nodes which kick the respective device in their own array. This facilitates the removal of failed devices. Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.de>
2015-04-22md-cluster: correct the num for comparisonGuoqing Jiang1-3/+3
Since the node num of md-cluster is from zero, and cinfo->slot_number represents the slot num of dlm, no need to check for equality. Signed-off-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com> Signed-off-by: NeilBrown <neilb@suse.de>
2015-03-21md/cluster: Communication Framework: fix semicolon.cocci warningskbuild test robot1-1/+1
drivers/md/md-cluster.c:328:2-3: Unneeded semicolon Removes unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
generated by cgit v1.2.3 (git 2.39.0) at 2024-11-18 14:57:46 +0300