| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- three new touchscreen drivers: EETI EXC3000, HiDeep, and Samsung
S6SY761
- the timer API conversion (setup_timer() -> timer_setup())
- a few drivers swiytched to using managed API for creating custom
device attributes
- other assorted fixed and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (50 commits)
Input: gamecon - mark expected switch fall-throughs
Input: sidewinder - mark expected switch fall-throughs
Input: spaceball - mark expected switch fall-throughs
Input: uinput - unlock on allocation failure in ioctl
Input: add support for the Samsung S6SY761 touchscreen
Input: add support for HiDeep touchscreen
Input: st1232 - remove obsolete platform device support
Input: convert autorepeat timer to use timer_setup()
media: ttpci: remove autorepeat handling and use timer_setup
Input: cyttsp4 - avoid overflows when calculating memory sizes
Input: mxs-lradc - remove redundant assignment to pointer input
Input: add I2C attached EETI EXC3000 multi touch driver
Input: goodix - support gt1151 touchpanel
Input: ps2-gpio - actually abort probe when connected to sleeping GPIOs
Input: hil_mlc - convert to using timer_setup()
Input: hp_sdc - convert to using timer_setup()
Input: touchsceen - convert timers to use timer_setup()
Input: keyboard - convert timers to use timer_setup()
Input: uinput - fold header into the driver proper
Input: uinput - remove uinput_allocate_device()
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are no big surprising changes in this cycle, yet not too boring,
either. The biggest change from diffstat POV is the removal of the
legacy OSS driver codes that have been already disabled for a long
time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the
malicious device accesses with a new helper code for endpoint
sanity check
- Lots of cleanups for ASoC Intel platform code, including support
for their open source audio firmware
- Continued ASoC core componentization works
- Support for scaling MCLK with sample rate in ASoC simple-card
- Stabler PCM hot-unplug capability, especially for ASoC usages"
* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
Documentation: sound: hd-audio: notes.rst
ASoC: bcm2835: Support left/right justified and DSP modes
ASoC: bcm2835: Enforce full symmetry
ASoC: bcm2835: Support additional samplerates up to 384kHz
ASoC: bcm2835: Add support for TDM modes
ASoC: add mclk-fs support to audio graph card
ASoC: add mclk-fs to audio graph card binding
ASoC: rt5514: work around link error
ASoC: rt5514: mark PM functions as __maybe_unused
ASoC: rt5663: Check the JD status in the button pushing
ASoC: amd: Modified DMA transfer Mechanism for Playback
ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
ASoC: da7213: add support for DSP modes
ASoC: sun8i-codec: Add a comment on the LRCK inversion
ASoC: sun8i-codec: Set the BCLK divider
ASoC: rt5663: Delay and retry reading rt5663 ID register
ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
ASoC: cs42l56: Fix reset GPIO name in example DT binding
ASoC: rt5514-spi: check irq status to schedule data copy in resume function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
|
|
Prepare input updates for 4.15 merge window.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer updates from Dmitry Torokhov:
- a new ACPI ID for Elan touchpad found in yet another Ideapad model
- Synaptics RMI4 will allow binding to controllers reporting SMB
version 3 (note that we are not adding any new ACPI IDs to the
Synaptics PS/2 drover so unless user explicitly enables intertouch
support there is no user-visible change)
- a fixup to TSC 2004/5 touchscreen driver to mark input devices as
"direct" to help userspace identify the type of device they are
dealing with
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - RMI4 can also use SMBUS version 3
Input: tsc200x-core - set INPUT_PROP_DIRECT
Input: elan_i2c - add ELAN060C to the ACPI table
|
|
'asoc/topic/amd' and 'asoc/topic/arizona-mfd' into asoc-next
|
|
The S6SY761 touchscreen is a capicitive multi-touch controller
for mobile use. It's connected with i2c at the address 0x48.
This commit provides a basic version of the driver which can
handle only initialization, touch events and power states.
The controller is controlled by a firmware which, in the version
I currently have, doesn't provide all the possible
functionalities mentioned in the datasheet.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The HiDeep touchscreen device is a capacitive multi-touch controller
mainly for multi-touch supported devices use. It use I2C interface for
communication to IC and provide axis X, Y, Z locations for ten finger
touch through input event interface to userspace.
It support the Crimson and the Lime two type IC. They are different
the number of channel supported and FW size. But the working protocol
is same.
Signed-off-by: Anthony Kim <anthony.kim@hideep.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 1fa59bda21c7fa36 ("ARM: shmobile: Remove legacy board code for
Armadillo-800 EVA"), removed the last user of st1232_pdata and the
"st1232-ts" platform device. All remaining users use DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with mainline to bring in SPDX markings to avoid annoying merge
problems when some header files get deleted.
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices.
In order to identify a touchscreen device, Android for example, seems to
already depend on INPUT_PROP_DIRECT to be present in drivers. udev still
checks for either BTN_TOUCH or INPUT_PROP_DIRECT. Checking for BTN_TOUCH
however can quite easily lead to false positives; it's a code that not only
touchscreen device drivers use.
According to the documentation, touchscreen drivers should have this
property set and in order to make life easy for userspace, let's set it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just a couple of fixups to the sparse-keymap module and the Microchip
AR1021 touchscreen driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sparse-keymap - send sync event for KE_SW/KE_VSW
Input: ar1021_i2c - set INPUT_PROP_DIRECT
|
|
If INPUT_PROP_DIRECT is set, userspace doesn't have to fall back to old
ways of identifying touchscreen devices. Let's add it.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There are several places to perform subtraction to calculate buffer
size such as:
si->si_ofs.cydata_size = si->si_ofs.test_ofs - si->si_ofs.cydata_ofs;
...
p = krealloc(si->si_ptrs.cydata, si->si_ofs.cydata_size, GFP_KERNEL);
Actually, data types of above variables during subtraction are size_t, so
it is unsigned. That means if second operand(si->si_ofs.cydata_ofs) is
greater than the first operand(si->si_ofs.test_ofs), then resulting
si->si_ofs.cydata_size could result in an unsigned integer wrap which is
not desirable.
The proper way to correct this problem is to perform a test of both
operands to avoid having unsigned wrap.
Signed-off-by: Vince Kim <vince.k.kim@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pointer 'input' is being initialized with ts->ts_input and this
value is not being read as it is updated a few lines later with the
return value from the call to devm_input_allocate_device. Remove the
redundant initialization assignment. Cleans up clang warning:
drivers/input/touchscreen/mxs-lradc-ts.c:587:20: warning: Value Xi
stored to 'input' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The 3000 series have a new protocol which allows to report up to 5 points
in a single 66 byte frame. One must always read in 66 byte frames.
To support up to 10 points, two consecutive frames need to be read:
The first frame says how many points until sync.
The second frame must say zero points or both frames must be discarded.
To be able to work with the higher 400KHz I2C bus rate, one must
successfully send a special package prior _each_ read or the controller
will refuse to cooperate.
This is a minimal implementation based on egalax_i2c.c (which can be found
on the internet) and egalax_ts.c but without the vendor interface and no
power management support.
Signed-off-by: Ahmet Inan <inan@distec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Support was added based on Goodix GitHub repo [1]. There are two major
differences between gt1151 and currently supported devices (gt9x):
* CONFIG_DATA register has 0x8050 address instead of 0x8047,
* config data checksum has 16-bit width instead of 8-bit.
Also update goodix_i2c_test() function, so it reads ID register (which
has the same address for all devices) instead of CONFIG_DATA (because
its address is known only after reading ID of the device).
[1] https://github.com/goodix/gt1x_driver_generic
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Stephen Lu <lumotuwe@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge with mainline to bring in the timer API changes.
|
|
We want the IIO and staging driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- joydev now implements a blacklist to avoid creating joystick nodes
for accelerometers found in composite devices such as PlaStation
controllers
- assorted driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ims-psu - check if CDC union descriptor is sane
Input: joydev - blacklist ds3/ds4/udraw motion sensors
Input: allow matching device IDs on property bits
Input: factor out and export input_device_id matching code
Input: goodix - poll the 'buffer status' bit before reading data
Input: axp20x-pek - fix module not auto-loading for axp221 pek
Input: tca8418 - enable interrupt after it has been requested
Input: stmfts - fix setting ABS_MT_POSITION_* maximum size
Input: ti_am335x_tsc - fix incorrect step config for 5 wire touchscreen
Input: synaptics - disable kernel tracking on SMBus devices
|
|
This adds support for the EDT M12 series of touchscreens.
Signed-off-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Since the driver also is useful for some non-EDT touchscreens based on
the focaltec chips introduce the concept of a "generic" focaltec based
touch.
Use a better heuristics for model detection and be more specific in the
source.
Signed-off-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Goodix panel triggers an interrupt on touch events. However, its
registers will contain the valid values a short time after the
interrupt, and not when it's raised. At that moment, the 'buffer status'
bit is set.
Previously, if the 'buffer status' bit was not set when the registers
were read, the data was discarded and no input event was emitted,
causing "finger down" or "finger up" events to be missed sometimes.
This went unnoticed until v4.9, as the DesignWare I2C driver commonly
used with this driver had enough latency for that bug to never trigger
until commit 2702ea7dbec5 ("i2c: designware: wait for disable/enable only
if necessary").
Now, in the IRQ handler we will poll (with a timeout) the 'buffer status'
bit and process the data of the panel as soon as this bit gets set.
Note that the Goodix panel will send a few spurious interrupts after the
'finger up' event, in which the 'buffer status' bit will never be set.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: russianneuromancer@ya.ru
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[hdegoede@redhat.com: Change poll loop to use jiffies,
add comment about typical poll time]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dtor: rearranged control flow a bit to avoid explicit goto and double
check]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The commit 78bcac7b2ae1e ("Input: add support for the STMicroelectronics
FingerTip touchscreen) used the 'touchscreen_parse_properties()' helper
function in order to get the value of common properties.
But, commit 78bcac7b2ae1e didn't set the capability of ABS_MT_POSITION_*
before calling touchscreen_parse_properties(). In result, the max_x and
max_y of 'struct touchscreen_properties' were not set.
Fixes: 78bcac7b2ae1e ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Cc: stable@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Step config setting for 5 wire touchscreen is incorrect for Y coordinates.
It was broken while we moved to DT. If you look close at the offending
commit bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made
configurable"), the change was:
- STEPCONFIG_XNP | STEPCONFIG_YPN;
+ ts_dev->bit_xn | ts_dev->bit_yp;
while bit_xn = STEPCONFIG_XNN and bit_yp = STEPCONFIG_YNN. Not quite the
same.
Fixes: bb76dc09ddfc ("input: ti_am33x_tsc: Order of TSC wires, made configurable")
Signed-off-by: Jeff Lance <j-lance1@ti.com>
[vigneshr@ti.com: Rebase to v4.14-rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Drop the arguments from the macro and adjust all callers with the
following script:
perl -pi -e 's/DEFINE_TIMER\((.*), 0, 0\);/DEFINE_TIMER($1);/g;' \
$(git grep DEFINE_TIMER | cut -d: -f1 | sort -u | grep -v timer.h)
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # for m68k parts
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog parts
Acked-by: David S. Miller <davem@davemloft.net> # for networking parts
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # for wireless parts
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-11-git-send-email-keescook@chromium.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
relative sysfs_remove_group and goto label.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
relative sysfs_remove_group.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Commit 57b8ff070f98 ("driver core: add devm_device_add_group() and
friends") has added the managed version for creating sysfs group files.
Use devm_device_add_group instead of sysfs_create_group and remove the
action that cleans the sysfs file when exiting the driver.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Change control of TOUCHSCREEN_USB_EASYTOUCH prompt string from
EMBEDDED to EXPERT to match the rest of this Kconfig file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
|
|
instead of sysfs_create_group.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for the new AC97 bus code, which discovers the devices
rather than uses platform data.
As part of this discovery, it enables a multi-function device wm97xx,
which supports touchscreen, battery, ADC and an audio codec. This patch
adds the code to bind the touchscreen "cell" as the touchscreen driver.
This was tested on the pxa architecture with a pxa270 + wm9713 + the
mioa701 touchscreen.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
wm97xx-core does several things in it initialization :
- touchscreen input device setup
- battery device creation
As the wm97xx is actually a multi-function device handling an audio
codec, a touchscreen, a gpio block and an ADC, reshape the probing to
isolate what is truly input/touchscreen specific from the remaining
part.
This is only code shuffling, there is no functional change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
Instead of stopping the touchscreen we were starting it in suspend, and
disabling it in resume.
Fixes: c899afedf168 ("Input: ucb1400_ts - convert to threaded IRQ")
Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
reg_addr->reg_report_rate is supposed to exist in M06, not M09.
The driver is written to skip avoids access to non-existing registers
when the register address is NO_REGISTER (0xff). But
reg_addr->reg_report_rate is initialized to 0x00 by devm_kzalloc() (in
edt_ft5x06_ts_probe()) and not changed thereafter. So the checks do
not work and an access to register 0x00 is done.
Fix by setting reg_addr->reg_report_rate to NO_REGISTER.
Also fix the only place where reg_report_rate is checked against zero
instead of NO_REGISTER.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Don't populate the const array header on the stack, instead make it
static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
6003 1536 0 7539 1d73 surface3_spi.o
After:
text data bss dec hex filename
5726 1632 0 7358 1cbe surface3_spi.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some x86 tablets with a Goodix touchscreen, the Windows logo on the
front is a capacitive home button. Touching this button results in a touch
with bit 4 of the first byte set, while only the lower 4 bits (0-3) are
used to indicate the number of touches.
Report a KEY_LEFTMETA press when this happens.
Note that the hardware might support more than one button, in which
case the "id" byte of coor_data would identify the button in question.
This is not implemented as we don't have access to hardware with
multiple buttons.
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is now handled via some macro magic during the register. The
field in iio_info will be removed shortly.
Cc: Linux Input <linux-input@vger.kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
