summaryrefslogtreecommitdiff
path: root/drivers/input/touchscreen/edt-ft5x06.c
AgeCommit message (Collapse)AuthorFilesLines
2014-12-31Merge branch 'for-linus' of ↵Linus Torvalds1-1/+3
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input layer fixes from Dmitry Torokhov: "Fixes for v7 protocol for ALPS devices and few other driver fixes. Also users can request input events to be stamped with boot time timestamps, in addition to real and monotonic timestamps" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: hil_kbd - fix incorrect use of init_completion Input: alps - v7: document the v7 touchpad packet protocol Input: alps - v7: fix finger counting for > 2 fingers on clickpads Input: alps - v7: sometimes a single touch is reported in mt[1] Input: alps - v7: ignore new packets Input: evdev - add CLOCK_BOOTTIME support Input: psmouse - expose drift duration for IBM trackpoints Input: stmpe - bias keypad columns properly Input: stmpe - enforce device tree only mode mfd: stmpe: add pull up/down register offsets for STMPE Input: optimize events_per_packet count calculation Input: edt-ft5x06 - fixed a macro coding style issue Input: gpio_keys - replace timer and workqueue with delayed workqueue Input: gpio_keys - allow separating gpio and irq in device tree
2014-12-17Merge branch 'for-linus' of ↵Linus Torvalds1-4/+2
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input subsystem updates from Dmitry Torokhov: "Two new drivers for Elan hardware (for I2C touchpad and touchscreen found in several Chromebooks and other devices), a driver for Goodix touch panel, and small fixes to Cypress I2C trackpad and other input drivers. Also we switched to use __maybe_unused instead of gating suspend/ resume code with #ifdef guards to get better compile coverage" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits) Input: gpio_keys - fix warning regarding uninitialized 'button' variable Input: add support for Elan eKTH I2C touchscreens Input: gpio_keys - fix warning regarding uninitialized 'irq' variable Input: cyapa - use 'error' for error codes Input: cyapa - fix resuming the device Input: gpio_keys - add device tree support for interrupt only keys Input: amikbd - allocate temporary keymap buffer on the stack Input: amikbd - fix build if !CONFIG_HW_CONSOLE Input: lm8323 - missing error check in lm8323_set_disable() Input: initialize device counter variables with -1 Input: initialize input_no to -1 to avoid subtraction Input: i8042 - do not try to load on Intel NUC D54250WYK Input: atkbd - correct MSC_SCAN events for force_release keys Input: cyapa - switch to using managed resources Input: lifebook - use "static inline" instead of "inline" in lifebook.h Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resume Input: mouse - use __maybe_unused instead of ifdef around suspend/resume Input: misc - use __maybe_unused instead of ifdef around suspend/resume Input: cap11xx - support for irq-active-high option Input: cap11xx - add support for various cap11xx devices ...
2014-12-16Input: edt-ft5x06 - fixed a macro coding style issueAsaf Vertz1-1/+3
Fixed a coding style error, macros with complex values should be enclosed in parentheses. Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-11-02Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resumeJingoo Han1-4/+2
Use __maybe_unused instead of ifdef guards around suspend/resume functions, in order to increase build coverage and fix build warnings. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-10-14input: edt-ft5x06: replace strnicmp with strncasecmpRasmus Villemoes1-1/+1
The kernel used to contain two functions for length-delimited, case-insensitive string comparison, strnicmp with correct semantics and a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper for the new strncasecmp to avoid breaking existing users. To allow the compat wrapper strnicmp to be removed at some point in the future, and to avoid the extra indirection cost, do s/strnicmp/strncasecmp/g. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-08-14Input: edt-ft5x06 - remove superfluous assignmentMaks Naumov1-1/+0
Somehow we ended up with a duplicate line in edt_ft5x06_register_write() Signed-off-by: Maks Naumov <maksqwe1@ukr.net> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-07-18Input: edt-ft5x06 - remove unnecessary null testFabian Frederick1-2/+1
Fix checkpatch warning: "WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required" Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-06-08Input: edt-ft5x06 - fix an i2c write for M09 supportRobert Woerle1-1/+1
The driver sends 3 bytes instead of 2 when accessing a register on the M09 firmware, so writing to gain seems to overflow into the offset register. Signed-off-by: Robert Woerle <robert@linuxdevelopment.de> Acked-By: Simon Budig <simon.budig@kernelconcepts.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-04-03Input: edt-ft5x06 - add a missing conditionDan Carpenter1-3/+4
The if condition was accidentally deleted here so we return every time instead of returning on error. Fixes: fd335ab04b3f ('Input: edt-ft5x06 - add support for M09 firmware version') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Jingoo Han <jg1.han@samsung.com> Acked-By: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-03-28Input: edt-ft5x06 - add support for M09 firmware versionLothar Waßmann1-82/+276
There is a new firmware version for the EDT-FT5x06 chip. Add support for detecting the firmware version and handle the differences appropriately. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-03-28Input: edt-ft5x06 - ignore touchdown eventsLothar Waßmann1-0/+4
The chip may report invalid coordinates on touchdown events, so don't report the initial touchdown event. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-03-28Input: edt-ft5x06 - adjust delays to conform datasheetLothar Waßmann1-3/+3
The FT5x06 datasheet specifies a minimum reset width of 5ms and a delay between deassertion of reset and start of reporting of 300ms. Adjust the delays to conform to the datasheet. With the original delays I sometimes experienced communication timeouts when initializing the controller. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-03-28Input: edt-ft5x06 - add DT supportLothar Waßmann1-31/+114
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-03-28Input: edt-ft5x06 - several cleanups; no functional changeLothar Waßmann1-9/+6
- remove redundant parens - remove redundant type casts - fix mixed tab/space indentation Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-01-21Input: edt_ft5x06 - use devm_* functions where appropriateLothar Waßmann1-43/+26
Simplify the error path and remove() function by using devm_* functions for requesting gpios and irq and allocating the input device. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-12-06Input: use dev_get_platdata()Jingoo Han1-1/+1
Use the wrapper function for retrieving the platform data instead of accessing dev->platform_data directly. This is a cosmetic change to make the code simpler and enhance the readability. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2013-03-31Input: edt-ft5x06 - remove redundant null check before kfreeSachin Kamat1-2/+1
kfree on a null pointer is a no-op. Hence null check is not necessary. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-24Input: remove use of __devexitBill Pemberton1-2/+2
CONFIG_HOTPLUG is going away as an option so __devexit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-24Input: remove use of __devinitBill Pemberton1-6/+6
CONFIG_HOTPLUG is going away as an option so __devinit is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-24Input: remove use of __devexit_pBill Pemberton1-1/+1
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer needed. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-10-30Merge tag 'v3.7-rc3' into next to sync up with recent USB and MFD changesDmitry Torokhov1-4/+7
2012-10-18Input: edt-ft5x06 - convert to use simple_open()Wei Yongjun1-9/+1
This removes an open coded simple_open() function and replaces file operations references to the function with simple_open() instead. dpatch engine is used to auto generate this patch. (https://github.com/weiyj/dpatch) Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-10-01Merge branches 'from-henrik', 'hidraw', 'logitech', 'picolcd', 'ps3', ↵Jiri Kosina1-4/+7
'uclogic', 'wacom' and 'wiimote' into for-linus
2012-09-20Input: edt-ft5x06 - return -EFAULT on copy_to_user() errorAxel Lin1-3/+6
copy_to_user() returns the number of bytes remaining, but we want a negative error code here. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2012-09-19Input: MT - Add flags to input_mt_init_slots()Henrik Rydberg1-1/+1
Preparing to move more repeated code into the mt core, add a flags argument to the input_mt_slots_init() function. Reviewed-and-tested-by: Benjamin Tissoires <benjamin.tissoires@enac.fr> Tested-by: Ping Cheng <pingc@wacom.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
2012-08-22Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FSGuenter Roeck1-1/+1
This fixes the following breakage: edt-ft5x06.c: In function edt_ft5x06_ts_remove: edt-ft5x06.c:846:14: error: struct edt_ft5x06_ts_data has no member named raw_buffer Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Simon Budig <simon.budig@kernelconcepts.de> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-07-25Input: add driver for FT5x06 based EDT displaysSimon Budig1-0/+898
This is a driver for the EDT "Polytouch" family of touch controllers based on the FocalTech FT5x06 line of chips. Signed-off-by: Simon Budig <simon.budig@kernelconcepts.de> Reviewed-by: Henrik Rydberg <rydberg@euromail.se> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-03-01 19:13:44 +0300